Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Resin 3D Printer Parts: Common Replacement Parts

Resin 3D printer parts wear out with use, and this guide explains the common replacement parts, how to spot a worn release film, and how to pick the right film size and material.

Resin 3D Printer Parts: Common Replacement Parts
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1KOYOFEI 6 PCS FEP Film for Resin 3D PrinterKOYOFEI 6 PCS FEP Film for Resin 3D Printer9.7/10View on Amazon
  2. 2Siraya Tech 2 Pcs NFEP Film 2.0 (Enhanced PFA)Siraya Tech 2 Pcs NFEP Film 2.0 (Enhanced PFA)9.6/10View on Amazon
  3. 3Original Photon Mono 2/Photon Mono 4 FEP Film 197Original Photon Mono 2/Photon Mono 4 FEP Film 1979.6/10View on Amazon
  4. 4ELEGOO 5PCS PFA Film for Saturn 3/4/4 Ultra/4ELEGOO 5PCS PFA Film for Saturn 3/4/4 Ultra/49.6/10View on Amazon

Resin 3D printer parts are the consumable pieces that keep a resin printer working, and the release film at the bottom of the vat is one part that needs replacing as it wears. The film separates each hardened layer from the vat floor, and as it wears, peel force rises, layer lines show, and prints start to fail. This guide explains the common replacement parts, how to spot a worn film, and how to pick the right size and material. The gear section below covers four release films.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

KOYOFEI 6 PCS FEP Film for Resin 3D Printer

KOYOFEI 6 PCS FEP Film for Resin 3D Printer

KOYOFEI9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

6 FEP films at 260 x 200 x 0.15 mm with 95% light transmission and heat resistance from -240°C to 205°C.

Pros

  • 6 films in the pack for repeated replacements
  • 95% light transmission keeps UV exposure stable
  • Heat-resistant from -240°C to 205°C
  • Fits Mars 4, Saturn, Photon Mono 2, Mono X and more models

Cons

  • 260 x 200 mm size fits only printers that take that size
  • No warranty term is stated
  • Sized for 7.1 to 9.25 inch mono printers; larger vats need a different film
  • No frame included; the film fits the vat frame
Siraya Tech 2 Pcs NFEP Film 2.0 (Enhanced PFA)

Siraya Tech 2 Pcs NFEP Film 2.0 (Enhanced PFA)

Siraya Tech9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An enhanced PFA release film in a 2-piece A4 set at 210 x 297mm, with ultra-low peel force for large and delicate prints.

Pros

  • Enhanced PFA with ultra-low release force, per the maker
  • A4 size fits LCD and DLP panels from 5.5 in to 10.1 in
  • Improved chemical resistance and mechanical strength for a longer life
  • Ultra-high UV transmittance for fast print speeds

Cons

  • No warranty term is stated
  • A4 sheet must be cut to size for smaller vats
  • Stated fit covers LCD and DLP printers only
  • Suits frequent printing; light users gain less from the upgrade
Original Photon Mono 2/Photon Mono 4 FEP Film 197

Original Photon Mono 2/Photon Mono 4 FEP Film 197

UniTak3D9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2-piece FEP film with a steel ring for the Photon Mono 2 and Mono 4, sized 197 x 131mm, with over 95% light transmittance.

Pros

  • Steel-ring design needs no cutting to install
  • Over 95% light transmittance
  • Heat resistant to 204 °C with chemical resistance
  • Maker states over thirty thousand releases

Cons

  • No warranty term is stated
  • Sized for the Photon Mono 2 and Mono 4 only
  • Fixed 0.15 thickness
  • A direct replacement; it adds no new capability to the printer
ELEGOO 5PCS PFA Film for Saturn 3/4/4 Ultra/4

ELEGOO 5PCS PFA Film for Saturn 3/4/4 Ultra/4

ELEGOO9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

5 PFA films at 273 x 176 mm and 0.127 mm thick with 92% light transmittance for Saturn resin printers.

Pros

  • 5 films in the pack for repeated replacements
  • 92% UV transmittance for faster and more even resin curing
  • 0.127 mm PFA film with a smooth, wrinkle-free surface
  • Fits Saturn 2, Saturn 3, Saturn 4 and Saturn 4 Ultra

Cons

  • 92% transmittance is lower than the 95% and over 95% figures here
  • 273 x 176 mm size fits Saturn and other 10-inch LCD printers only
  • No warranty term is stated
  • 5 films in the pack, against 6 in the KOYOFEI pack

How resin 3D printer parts wear out

A resin printer hardens liquid resin layer by layer, and the release film takes the strain. Each lift pulls the hardened layer away from the film, and over many prints the film loses its smooth release. The signs show in the print: layer lines grow more visible, delicate supports break free, and print success drops. Siraya Tech describes its NFEP 2.0 film as reducing layer lines and distortions by cutting the pulling force on hardened layers, compared with standard FEP. A fresh film peels cleanly, and a worn film drags. When clean prints start to struggle, check the film first. Resin handling calls for care; see the resin 3D printer safety guide and does 3D printer resin expire.

Resin 3D Printer Parts for the Vat

The four films below handle the release step: each film sits at the bottom of the vat and lets hardened layers peel away cleanly, so match the size and thickness to the printer before ordering.

How to pick the right film size

Match the film to the vat. The films in this guide span several sizes: an A4 sheet at 210 x 297mm for LCD and DLP printers with 5.5 in to 10.1 in panels, a 197 x 131mm sheet for the Photon Mono 2 and Mono 4, a 273 x 176mm sheet for the Saturn range, and a 260 x 200mm sheet for Mars, Saturn and Photon models. Thickness matters too: the UniTak and KOYOFEI films are 0.15mm thick, the ELEGOO film is 0.127mm, and Siraya Tech states no thickness for its NFEP 2.0 film. Light transmittance is the other figure: the UniTak film states over 95%, and the ELEGOO film states 92%. For a wider comparison, see the best FEP film guide.

FEP or NFEP: which film material

Standard FEP film is the common release film, and NFEP is the upgraded form. Siraya Tech builds its NFEP 2.0 film from an enhanced PFA material, which the maker says gives an ultra-low release force, improved chemical resistance, and a longer working life than standard FEP. The payoff is smoother finishes with fewer layer lines and better print success. Standard FEP still does the same job: the UniTak film pairs its FEP sheet with a steel ring for changes that need no cutting and states heat resistance to 204 °C, while the ELEGOO PFA film and the KOYOFEI FEP film cover the Saturn and Mars ranges at fixed sizes. Choose NFEP for large surface areas or delicate supports, and standard FEP for a straight replacement.

FAQ: lasers and CNC

How often should a resin printer release film be replaced?

No maker in this guide gives a fixed schedule. The UniTak listing states its film releases more than thirty thousand times, and Siraya Tech says its NFEP 2.0 film prints more models before a replacement is needed. Replace the film when layer lines grow worse or prints that used to succeed start to miss.

What is the difference between FEP and NFEP film?

NFEP is an enhanced PFA material, while standard FEP is the common release film. Siraya Tech says its NFEP 2.0 film gives an ultra-low release force, improved chemical resistance and mechanical strength, and a longer life than standard FEP, with smoother finishes and fewer layer lines. Standard FEP still releases hardened layers cleanly; NFEP is the upgrade for large surface areas and delicate supports.

How do I pick the right film size for my printer?

Match the film to the vat frame and to the printer model. The films here cover an A4 sheet at 210 x 297mm for LCD and DLP printers with 5.5 in to 10.1 in panels, a 197 x 131mm sheet for the Photon Mono 2 and Mono 4, a 273 x 176mm sheet for the Saturn range, and a 260 x 200mm sheet for Mars, Saturn and Photon models. The Siraya Tech sheet can be cut to size, while the UniTak film uses a steel ring and needs no cutting.

What light transmittance should a release film have?

The UniTak film states over 95% light transmittance, and the ELEGOO film states 92% light transmittance. Siraya Tech states ultra-high UV light transmittance for its NFEP 2.0 film, which the maker links to fast print speeds.

How thick should a release film be?

Check the thickness before ordering. The UniTak and KOYOFEI films are 0.15mm thick, and the ELEGOO film is 0.127mm. Siraya Tech states no thickness for its NFEP 2.0 film. Thickness is fixed per film, so check the figure before ordering.

Related: the SLA 3D printer parts guide, 3D printer replacement parts guide and 3D printers hub. Also see our best FEP film for Saturn 4 Ultra. Also see our 3D printer maintenance guide.

More buying guides

3D Printers ·

3D Printer Parts Kit: What Is Included

A 3D printer parts kit bundles the spares that keep a printer running, and this guide explains what each kind holds and how to…