3D Printer Replacement Parts Guide
Worn nozzles cause stringing and uneven lines, and clogs cut flow; this guide shows when to swap them, what a kit should hold, and which kits fit common Creality, Elegoo and Prusa machines.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Ender 3 Nozzles 0.4MM,20Pcs Brass Hotend Nozzles9.6/10View on Amazon - 2
ELEGOO 26pcs 0.4mm MK8 Nozzles for Neptune 3/39.6/10View on Amazon - 3
16Pcs V6 Nozzles kit Compatible for E3D V5 V69.6/10View on Amazon
A print that starts clean and then turns rough mid-print usually points at the nozzle, not the file. When the opening narrows or clogs, layers go thin, gaps open between lines and corners lose their edge. 3d printer replacement parts are the wear items that fix that drift: fresh nozzles, cleaning pins and the small tools that fit them. This guide shows how to spot a worn nozzle, match a kit to a machine and swap the part without a clog.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
This guide compares what each listing states about fit, size and contents.

Ender 3 Nozzles 0.4MM,20Pcs Brass Hotend Nozzles
A 20-piece set of 0.4 mm brass MK8 nozzles with a 16-piece cleaning kit, wrench, brushes, tweezers and a storage box.
Pros
- 20 brass 0.4 mm nozzles cover repeat swaps on the machines it lists
- Cleaning kit holds 10 steel pins, 2 brushes, 2 tweezers, a 6 mm wrench and a storage box
- Fits the Ender 3 range, Ender 5 Pro and CR 10 Series printers
- Brass nozzles are stated as heat resistant and corrosion resistant, with good abrasion resistance
Cons
- Only 0.4 mm nozzles; no 0.2 mm, 0.3 mm or 0.6 mm size in the box
- No warranty term is stated
- Cleaning pins need the print head heated to more than 200 degrees first
- Small parts in the kit are not suitable for children under 12 years old

ELEGOO 26pcs 0.4mm MK8 Nozzles for Neptune 3/3
26 brass 0.4 mm MK8 nozzles with 4 cleaning needles and a wrench for Neptune 3 and Ender 3 series machines.
Pros
- 26 brass 0.4 mm nozzles in the box for repeat swaps
- Nozzle size is marked on the surface, so the size reads at a glance
- CNC-made brass is stated as heat resistant and corrosion resistant, and the maker states less risk of print head leaks and nozzle clogging
- Fits Neptune 3 series and Ender 3 series machines
Cons
- Not for Neptune 4 series machines
- Only 0.4 mm nozzles; no other nozzle size in the box
- Only 4 cleaning needles for 26 nozzles
- No warranty term is stated

16Pcs V6 Nozzles kit Compatible for E3D V5 V6
A 16-piece V6 nozzle set in 0.2, 0.3, 0.4 and 0.6 mm with 10 cleaning needles in 10 sizes for M6 hotends.
Pros
- Nozzle sizes in the kit: 0.2, 0.3, 0.4 and 0.6 mm
- 10 cleaning needles in sizes up to 1.0 mm
- Brass M6 nozzles fit E3D V5 and V6 hotends
- Cleaning needles also fit MK8, MK10 and Volcano nozzles
Cons
- Only 2 nozzles each in 0.2, 0.3 and 0.6 mm; 10 of the 16 are 0.4 mm
- No wrench, brush or storage box is listed
- M6 thread only; machines without an M6 heat block need a different kit
- No tweezers are listed for handling hot nozzles
How to tell a nozzle is worn
A nozzle wears at the bore and at the tip. Filament drags through the same narrow opening on every print, and the bore slowly widens while the tip wears and picks up residue. The signs: lines that vary in width, small gaps between lines, strings across open spaces and a rough surface where the last print came out smooth.
A clog looks much like wear at first. Run a pin through a hot nozzle and print again; if the same flaws return, the bore has likely widened past useful life and a swap is the fix. Keep a spare nozzle in the same size so the swap is quick.
What to check before you order 3d printer replacement parts
Fit decides everything. Read the nozzle style first: MK8 and V6 nozzles both use an M6 thread, but they differ in length and shoulder shape, so a nozzle in the wrong style will not seat flush in the heat block. Then read the nozzle size: 0.4 mm is the size in the KITANIS and ELEGOO kits and the most common size in the TIEXYE kit (on Amazon), while 0.2 mm suits fine detail and 0.6 mm suits thick layers. Then read the filament diameter the kit states: 1.75 mm here, which matches the machines these kits list.
Last, read the machine list on the kit and match it to the printer on the desk. The KITANIS kit (on Amazon) lists the Ender 3 range, the Ender 5 Pro and the CR 10 Series. The ELEGOO kit lists Neptune 3, Neptune 3 Pro, Neptune 3 Plus, Neptune 3 Max and Ender 3 series machines, and it states plainly that it is not for Neptune 4 series machines. The TIEXYE kit lists E3D V5 and V6 hotends and machines with an M6 thread heat block. When the machine list and the nozzle style match, the kit fits. For Ender 3 upkeep beyond nozzles, the timing belt guide for Ender 3 covers the next wear item in line.
What a nozzle kit should hold
A useful kit holds the nozzle, the cleaning tools and the wrench in the same box, so a clog or a swap never waits on a missing tool. Nozzles come in the size the printer uses: 0.4 mm in the KITANIS and ELEGOO kits, and the most common size in the TIEXYE kit. Cleaning pins or needles come in sizes 0.15/0.2/0.25/0.3/0.35/0.4/0.5/0.6/0.8/1.0mm in the TIEXYE kit, so pick the needle that matches the nozzle bore; a needle wider than the bore will not pass through it. A wrench fits the nozzle flats: 6 mm in the KITANIS kit. A storage box keeps spare nozzles sorted by size.
Count the pieces before ordering: a printer that runs daily burns through spares faster than a printer that runs on weekends, so a kit with 20 or 26 nozzles lasts longer between orders than a kit with 16. A pin that matches the bore clears a clog and saves a spare nozzle for the next swap.
3d printer replacement parts for Ender, Neptune and Prusa machines
The kits below cover the nozzle swap and the cleaning that goes with it, so check the nozzle style and the machine list before ordering.
How to swap a nozzle and clear a clog
Heat comes first. The KITANIS guidance says to heat the print head to more than 200 degrees before cleaning, and the same heat makes a nozzle swap easier, since cold filament locks the nozzle in place. With the head hot, loosen the old nozzle with the wrench and fit the new nozzle in the same size.
For a clog, insert and remove the cleaning steel pin from the discharge port while the head stays hot, and repeat until the printer discharges normally. Let the head cool before touching the nozzle with bare hands, since the hot end can scald.
Common mistakes to avoid
- Ordering a V6 nozzle for an MK8 machine, or the reverse: both use an M6 thread, but the lengths differ, so the nozzle will not seat flush in the heat block.
- Ordering by nozzle count alone and skipping the machine list. The ELEGOO kit states it is not for Neptune 4 series machines.
- Cleaning a cold nozzle. Heat the print head to more than 200 degrees first, as the KITANIS guidance says, or the pin meets solid filament.
- Picking 0.6 mm for fine detail or 0.2 mm for thick layers: match the size to the print, not to the kit with the most pieces.
- Storing spare nozzles loose in a drawer, where the size marking rubs off and the next swap starts with a guess.
FAQ: lasers and CNC
How often should a 3D printer nozzle be replaced?
There is no fixed schedule in the listings here. Swap the nozzle when cleaning no longer clears the flaws, or when the bore has widened enough that lines vary in width. A printer that runs daily needs spares on hand.
What nozzle size should you buy first?
Start with 0.4 mm. Each kit below centers on 0.4 mm nozzles, and that size suits most prints on the machines these kits list. Add 0.2 mm for fine detail or 0.6 mm for thick layers only when a print calls for it.
Do MK8 and V6 nozzles fit the same printer?
No. Both use an M6 thread, but MK8 and V6 nozzles differ in length and shoulder shape, so a V6 nozzle does not seat the same way in an MK8 heat block. The KITANIS and ELEGOO kits are MK8, while the TIEXYE kit fits E3D V5 and V6 hotends. Match the nozzle style to the heat block before ordering.
Can a nozzle be cleaned instead of replaced?
Yes, when the bore is clogged rather than worn. Heat the print head to more than 200 degrees, then insert and remove the cleaning steel pin from the discharge port until the printer discharges normally. If the same flaws return on the next print, the nozzle is worn and a swap is the fix.
What filament do these nozzle kits fit?
All the kits here state 1.75 mm filament. The KITANIS kit names PLA and ABS; the other kits name no filament type, so check the filament the printer runs before ordering.
Related: the 3D printers hub, best PTFE tube for Bambu Lab and best 3D printer lubricant and grease kit. Also see the sanding sponge for 3D printing for print finishing.




