How to Use Reamer: Step-by-Step Basics
A reamer enlarges and finishes a hole that already exists: pick the size, turn it by hand, oil the cut and clear the chips.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Performance Tool W2967 2-Piece T-Handle Tapered9.6/10View on Amazon - 2
uxcell 10pcs Hand Reamers Set 3mm 4mm 5mm 6mm 7mm9.6/10View on Amazon - 3
uxcell Hand Reamers Set H8 Accuracy Alloy Tool9.5/10View on Amazon - 4
findmall 11Pcs Adjustable Reamers H4-H14 High9.5/10View on Amazon
The question of how to use reamer sets comes down to a short sequence: pick the reamer that matches the hole, turn it by hand, take a light cut, keep it oiled, and clear the chips as you go. A reamer enlarges and finishes a hole that already exists, so the work starts with the hole, not the tool.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
A reamer follows a hole that already exists: it enlarges, smooths and finishes, and it does not drill a fresh hole.

Performance Tool W2967 2-Piece T-Handle Tapered
A 2-piece T-handle tapered reamer set that aligns holes, removes burrs and enlarges and countersinks holes.
Pros
- Capacity ranges: 1/8 to 1/2 inch and 5/32 to 7/8 inch
- T-handle design for easy turning and sure handling
- Heat treated #45 high carbon steel for longer service life
- Lifetime warranty
Cons
- Tapered shape suits aligning and enlarging, not finishing a straight hole
- 2 pieces only, so it covers fewer sizes than the 10-piece sets here
- Top capacity of 7/8 inch, so a larger hole needs a bigger reamer
- T-handle design suits hand turning, not machine use

uxcell 10pcs Hand Reamers Set 3mm 4mm 5mm 6mm 7mm
A 10-piece set of fixed hand reamers, 3mm to 12mm, in 9SiCr alloy steel.
Pros
- 10 fixed sizes from 3mm to 12mm, H7 tolerance
- 9SiCr alloy steel with hardness, toughness and wear resistance
- Suits stainless steel, aluminum, copper, alloy, plastic and wood
- Cutting fluid or lubricant improves finish and tool life
Cons
- 10 pieces cover 3mm to 12mm only, so a larger hole needs a bigger set
- Straight flutes need chips cleared, or cutting performance will be affected
- No warranty term is stated
- Needs a wrench, T-handle wrench, extension rod or drill chuck

uxcell Hand Reamers Set H8 Accuracy Alloy Tool
A 10-piece set of fixed hand reamers, 3mm to 12mm, in alloy tool steel with 6 flutes.
Pros
- 10 fixed sizes from 3mm to 12mm, H8 accuracy class
- 6 flutes, straight shank, for finish cuts
- Alloy tool steel with high hardness and durability
- Suits aluminum, cast iron, copper, plastic and wood
Cons
- 10 pieces cover 3mm to 12mm only, so a larger hole needs a bigger set
- Chips collect in the flutes, so the reamer needs cleaning in use
- No warranty term is stated
- Hand operated by wrench

findmall 11Pcs Adjustable Reamers H4-H14 High
An 11-piece set of adjustable hand reamers, 11.75mm to 38mm, in high speed steel.
Pros
- 11 adjustable reamers covering 11.75mm to 38mm
- High speed steel with good hardness and toughness
- Straight flute and handle, for drilling machines
- Covers the largest holes here, above the 12mm fixed sets
Cons
- Starts at 11.75mm, so a smaller hole needs a fixed set
- 11 pieces is a large set for a maker who only reams one size
- Wide range, so no size gets a dedicated fixed reamer
- 11 pieces to keep track of, against 2 in the tapered set
Step 1: Pick the reamer that matches the hole
A fixed reamer cuts one size: the sets here cover 3mm to 12mm. An adjustable reamer covers a range. A tapered reamer aligns holes and enlarges them.
Step 2: Start with a hole that already exists
A reamer enlarges, smooths and finishes a hole; it does not drill a fresh one. The hole comes first, and the reamer follows it to size.
Step 3: Turn the reamer by hand
The tapered set has a T-handle for turning. The H7 set turns with a wrench, a T-handle wrench, an extension rod or a drill chuck, and the H8 set turns with a wrench. Take a light cut.
Step 4: Oil the cut
The makers advise machine oil for the H8 set and cutting fluid or lubricant for the H7 set.
Step 5: Clear the chips as you go
Straight flutes let chips collect in the flutes, and if chips clog the flutes, cutting performance will be affected.
The reamer sets in this guide
The sets below cover the tapered, fixed and adjustable shapes: the tapered set aligns and deburrs, the fixed sets finish holes to a set size, and the adjustable set covers a range.
Common mistakes to avoid
- Skipping machine oil or cutting fluid.
- Letting chips clog the flutes.
- Using a fixed reamer outside its size range.
- Using a reamer to drill a fresh hole.
- Leaving a reamer dirty between jobs.
How to use reamer: the short version
- Pick the reamer that matches the hole.
- Start with a hole that already exists.
- Turn it by hand with a wrench or T-handle.
- Oil the cut.
- Clear the chips and check the fit.
FAQ: lasers and CNC
What is a reamer used for?
A reamer enlarges, smooths and finishes a hole that already exists, and the tapered set also aligns holes and removes burrs.
What is the difference between a fixed and an adjustable reamer?
A fixed reamer cuts one size: the sets here cover 3mm to 12mm. An adjustable reamer covers a range.
Can a reamer drill a new hole?
No. A reamer enlarges and finishes a hole that already exists, so start with a drilled hole.
Do I need oil when using a reamer?
Yes. The makers advise machine oil for the H8 set and cutting fluid or lubricant for the H7 set, to reduce friction and improve the finish.
What size reamer do I need?
Match the reamer to the hole: the fixed sets cover 3mm to 12mm and the adjustable set covers 11.75mm to 38mm.
Related: best HSS reamer set, drill bit types for metal, how to use a Forstner drill bit and CNC tooling.




