Reamer Size Chart: Choosing the Right Reamer
A reamer size chart lists the sizes to pick from, from taper sets that align bolt holes to chucking reamers that finish holes on a drill press.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Reamer Drill Bit for Metal,5 PCS Bridge9.7/10View on Amazon - 2
5-Piece 3/8", 1/2", 5/8", 3/4"9.6/10View on Amazon - 3
Drill America 5 Piece Bridge/Construction Reamer9.6/10View on Amazon - 4
Drill America 5 Piece Chucking Reamer Set9.6/10View on Amazon
A reamer size chart answers a simple question: which reamer fits the hole you need. The chart lists reamer sizes, so a maker can pick the reamer that matches the bolt or rivet that must fit. Read the chart by the size needed, and match the reamer type to the job: a taper reamer aligns holes, a chucking reamer finishes them.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Every size in this guide comes from the reamer listings themselves, and the picks carry the sizes their makers state.

Reamer Drill Bit for Metal,5 PCS Bridge
A 5-piece M2 HSS bridge reamer set, 3/8 to 1 inch, with 5-spiral flutes and a 1/2 inch shank with 3-flat for pre-drilled holes in steel and alloy.
Pros
- 5 sizes, 3/8 to 1 inch, with a 1/2 inch shank for a 1/2 inch chuck
- M2 HSS, 5-spiral flutes, for steel, alloy, aluminum, plastic, iron, nickel, wood, cast iron
- 1/2 inch shank with 3-flat for a firm grip in portable electric or pneumatic tools
- Suits bridge, construction, steel erection and automotive work
Cons
- No storage case is stated
- No warranty term is stated
- Sizes stop at 1 inch
- Needs a pilot hole, cutting oil and low speed

5-Piece 3/8", 1/2", 5/8", 3/4"
A 5-piece M2 HSS taper reamer set, 3/8 to 1 inch, with 5-spiral flutes and a 1/2 inch non-slip shank for holes in steel, alloy, wood and plastic.
Pros
- 5 sizes from 3/8 to 1 inch in a set
- M2 HSS with 5-spiral flutes for steel, alloy, wood and plastic
- Tapered point for precise alignment and smooth entry into pre-drilled holes
- 1/2 inch non-slip shank for a firm grip
Cons
- No storage case is stated
- No warranty term is stated
- Sizes stop at 1 inch
- Aligns and enlarges existing holes only

Drill America 5 Piece Bridge/Construction Reamer
A 5-piece high speed steel bridge reamer set, 3/8 to 1 inch, in a plastic pouch case, with a tapered point and a 1/2 inch shank for aligning holes before bolting.
Pros
- 5 sizes from 3/8 to 1 inch in a plastic pouch case
- Tapered point permits entry into overlapping holes
- Short length for areas with limited access
- Three flats on the shank give a positive grip in portable electric and pneumatic tools
Cons
- Sizes stop at 1 inch
- Cutting oil is not stated as included
- Short length suits tight spots but gives less reach in deep holes
- Aligns existing holes only

Drill America 5 Piece Chucking Reamer Set
A 5-piece high speed steel chucking reamer set from 3/16 to 1/2 inch, with a straight-flute design and a 45º chamfer for general-purpose reaming.
Pros
- 5 sizes from 3/16 to 1/2 inch for small finished holes
- High speed steel, straight-flute, for most general-purpose reaming
- 45º chamfer for a regular point
- Fits screw machines, turret lathes, drill presses and machining centers
Cons
- No pouch or case is stated
- Largest size is 1/2 inch
- Chamfered point, not a long taper, so it cannot align misaligned holes
- Stated fit is screw machines, turret lathes, drill presses and machining centers
How to read a reamer size chart
Start with the size needed: for a finished hole, find the chucking reamer with the same size. The taper sets below list sizes from 3/8 inch to 1 inch, with a chucking set that runs from 3/16 inch to 1/2 inch. A taper reamer suits holes that need aligning before a bolt goes in, while a chucking reamer suits a smooth finish on a drill press or lathe.
Taper reamers vs chucking reamers
A taper reamer has a tapered point that enters a pre-drilled hole and enlarges misaligned holes so a bolt can pass, which suits bridge and construction bolting work. A chucking reamer has straight flutes with a chamfered point and finishes a drilled hole to size, which is why the Drill America DWRR set lists screw machines, turret lathes, drill presses and machining centers as its fit. The NOVINO set states the rule plainly: a taper reamer only aligns or enlarges an existing hole.
Match the reamer to the hole
Pick the reamer by the size needed, then, for the NOVINO set, follow its steps: pilot hole, cutting oil, low speed at entry, gradually increase speed once the reamer is engaged, clamp the workpiece, and reduce speed as the hole nears size. For a full comparison of end mills, see our 1/4 vs 3/8 inch end mill guide.
Reamer sets that cover the chart
When the chart points to a size, the sets below hold the reamer for it.
Common mistakes to avoid
- Reading the drill size as the finished size.
- Using a taper reamer to drill a fresh hole in solid material.
- Reaming at high speed without cutting oil.
- Ordering a chucking reamer to align holes that sit out of line.
Reamer size chart: the short version
- Name the size needed.
- Pick a taper reamer to align holes, a chucking reamer to finish them.
- Start with a pilot hole and cutting oil.
- Start at low speed, increase speed once the reamer is engaged, then reduce speed near the finished size.
- Check the fit with the bolt or rivet.
FAQ: lasers and CNC
What does a reamer size chart show?
It lists reamer sizes. A chucking reamer finishes a hole to its listed size, while a taper reamer aligns or enlarges an existing hole.
What is the difference between a taper reamer and a chucking reamer?
A taper reamer aligns existing holes with a tapered point, while a chucking reamer finishes a drilled hole to size.
Can a reamer drill a fresh hole?
No. A reamer only works in an existing hole: a taper reamer only aligns or enlarges one, and a chucking reamer only finishes a drilled hole.
Which sizes do the sets here cover?
The taper sets here cover 3/8 inch to 1 inch, while the chucking set covers 3/16 inch to 1/2 inch for smaller finished holes.
Do I need cutting oil when reaming?
For the taper sets here, yes. The NOVINO and DECKRKAT listings state cutting oil reduces friction and helps the reamer cut smoothly, so apply it before reaming with those sets.
Related: the best downcut CNC bit, best CNC bit set for engraving and best dado bit for CNC. Also see our how to set up a spoilboard on a CNC.




