How to Use a Forstner Drill Bit: A Shop Guide
A Forstner bit drills clean, flat-bottomed holes in wood and plastic when you mark the center, clamp the workpiece, and let the center spur guide the cut.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
CORTOOL Forstner Bit Set 16Pcs Hex Shank9.6/10View on Amazon - 2
COMOWARE Forstner Bit Set 16 PCS for Woodworking9.6/10View on Amazon - 3
BAIDETS Forstner Bit Set 8Pcs9.5/10View on Amazon - 4
Devvicoo Forstner Bit Set9.5/10View on Amazon
A Forstner bit is the tool for a clean, flat-bottomed hole in wood, and learning how to use a forstner drill bit starts with the center mark. The center spur sits on the mark and holds the bit in place while the rim cutters shear the wood, so the hole lands where you marked it and the bottom stays flat. This guide walks through marking, clamping, picking a size and drilling, plus the bit sets that cover the work.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

CORTOOL Forstner Bit Set 16Pcs Hex Shank
A 16-piece set from 1/4 to 2-1/8 inch with a 3/8 inch hex shank and extra-sharp cutting spurs for flat-bottomed holes in wood and plastic.
Pros
- 16 pieces from 1/4 to 2-1/8 inch cover hinge holes and wide bores
- 3/8 inch hex shank resists slipping in the chuck
- Extra-sharp cutting spurs cut hard and soft wood smoothly
- Makes flat-bottomed pocket holes with no chipping
Cons
- 16 pieces take more storage than an 8-piece set
- Wide bits up to 2-1/8 inch need a steady drill press setup
- No smaller set option for buyers who need only a few sizes
- Hex shank only, with no round-shank version in this set

COMOWARE Forstner Bit Set 16 PCS for Woodworking
A 16-piece heat-treated carbon steel set from 1/4 to 2-1/8 inch with an X-wing design and a sharp center spur for clean, flat-bottomed holes.
Pros
- 16 pieces from 1/4 to 2-1/8 inch cover the full size range
- Heat-treated carbon steel with precision-ground cutting edges
- X-wing design clears chips fast with chisel-like curls
- Sharp center spur locates the hole without walking
Cons
- Round shank can slip in a worn chuck where a hex shank holds
- 16 pieces take more storage than an 8-piece set
- Wide bits up to 2-1/8 inch need a steady drill press setup
- Carbon steel needs drying after use to help prevent rust

BAIDETS Forstner Bit Set 8Pcs
An 8-piece carbon steel set in the most commonly used sizes from 1/4 to 1-3/8 inch, with a center tooth for precise positioning.
Pros
- 8 most commonly used sizes from 1/4 to 1-3/8 inch
- Center tooth holds position and stops the bit from walking
- Tooth-shaped bevel edge cuts with less friction and heat
- Rounded edge design keeps each hole round and clean
Cons
- Only 8 sizes, with nothing above 1-3/8 inch
- No larger sizes for wide hinge holes or wide bores
- No warranty term is stated
- Center tooth leaves a small mark at the center of the hole bottom

Devvicoo Forstner Bit Set
An 8-piece carbon steel set in commonly used sizes from 1/4 to 1-3/8 inch, with a central tooth for stable, accurate drilling.
Pros
- 8 commonly used sizes from 1/4 to 1-3/8 inch
- Central tooth holds position without shaking or walking
- Tooth-shaped bevel edge cuts with less friction and heat
- Suits hinge holes, drawer slides, plywood and plastics
Cons
- Only 8 sizes, with nothing above 1-3/8 inch
- No warranty term is stated
- No 16-piece option for buyers who want the full size range
- Carbon steel needs drying after use to help prevent rust
How to Use a Forstner Drill Bit Step by Step
Mark the center of the hole with a pencil or an awl, then clamp the workpiece to the bench or the drill press table so it cannot spin or lift. Pick the bit that matches the hole you need, check the size on the shank, and seat the bit firmly in the chuck. Set the workpiece flat, line the center spur up on the mark, and start the drill before the cutters touch the wood.
Feed the bit with steady, even pressure and let the cutters do the work. Lift the bit clear of the hole often to let the chips out, since packed chips heat the bit and roughen the cut. Keep the bit square to the surface through the cut, and ease off the pressure as the bit breaks through the far side to reduce tear-out on the exit.
Stop when the hole reaches the depth you marked, back the bit out while it still spins, and brush the chips clear before you check the fit. A hinge cup or a dowel should sit flush in a flat-bottomed hole, and another pass with the same bit cleans up any ridges the first pass left behind.
Pick the Right Size for the Hole
Match the bit to the hole the hardware needs: a hinge cup, a dowel or a plug sets the diameter, and the bit should match it, not the nearest size in the box. The sets in this guide run from 1/4 inch to 2-1/8 inch, with the 16-piece sets covering the full range and the 8-piece sets covering the common sizes from 1/4 inch to 1-3/8 inch. A bit that is wider than the hardware leaves a loose fit, and a bit that is narrower leaves a hole the hardware will not fit. For other CNC work, the best CNC bit set for woodworking rounds out the bit box.
Measure the hardware before you drill, and check the size stamped on the bit against the size you need. Keep the bits in size order in the box so the right one is easy to find, and wipe each bit dry after use to help keep it from rusting.
Drill Press or Hand Drill
A drill press holds the bit square and feeds it straight, which is the easy way to get a flat bottom and a clean rim on a wide hole. A hand drill works for smaller holes in a clamped workpiece, with a firm grip and a steady feed. The BAIDETS and Devvicoo listings state their sets suit power drills, bench drills, vertical drills, hand drills and floor drills, and the COMOWARE set suits drill presses and handheld drills, so pick the machine that holds the workpiece still and the bit square. A countersink bit cuts the angled seat for a screw head if the hole needs one; see the best countersink drill bit set for wood.
Forstner bits cut with a shearing rim, so they need the workpiece held still more than they need force. Clamp the work, keep the bit square, and let the center spur hold the position. If the bit wanders, stop and re-mark the center rather than forcing the cut.
The Gear for Drilling Flat-Bottomed Holes
Each set below covers a part of the job, from the full size range for hinge holes and wide bores to the common sizes for everyday drilling.
Common Mistakes to Avoid
- Drilling without clamping the workpiece, so the bit catches and spins the wood.
- Picking a bit by eye instead of checking the size on the shank.
- Forcing the bit when the chips pack the hole, which heats the edge and roughens the cut.
- Letting the bit wander off the mark instead of stopping to re-mark the center.
- Storing damp bits in the box, which lets them rust.
FAQ: lasers and CNC
Can you use a Forstner bit in a hand drill?
Yes. The BAIDETS and Devvicoo listings state their sets suit hand drills, bench drills and drill presses, and the COMOWARE set suits handheld drills and drill presses. Clamp the workpiece, keep the bit square, and use a hand drill for the smaller sizes; wide holes are easier on a drill press.
What size Forstner bit do I need for a hinge hole?
Measure the hinge cup and match the bit to it. The 8-piece sets here cover sizes from 1/4 inch to 1-3/8 inch, and the 16-piece sets run from 1/4 inch to 2-1/8 inch, so the size you need is likely in the box.
Do Forstner bits work in plastic?
Yes. The listings state these bits cut wood, plywood and plastic, and the COMOWARE set also lists resin and PVC. Use a steady feed and clear the chips so the plastic does not heat and melt onto the cutters.
How do you keep a Forstner bit from walking?
Mark the center clearly and let the center spur sit on the mark before the cutters touch the wood. The center spur holds position and stops the bit from walking, so start the cut with light pressure and let the spur seat first.
Can a Forstner bit drill a flat-bottomed hole?
Yes, that is what it is made for. The rim cutters shear the wood to a flat bottom, and the center tooth leaves only a small mark at the center. Drill to the depth you marked, clear the chips, and check the fit before you move on.
Related: best router bit for beginners, end mill vs drill bit for CNC, best CNC bit set for beginners and how to set up a spoilboard on a CNC.




