What Size Forstner Bit for Cabinet Hinges: 1-3/8 Inch
A 1-3/8 inch (34.9 mm) Forstner bit bores the cup for a cabinet hinge, and four bit sets are compared on the sizes they include.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
BAIDETS Forstner Bit Set 16Pcs9.6/10View on Amazon - 2
CORTOOL Forstner Bit Set 8Pcs Hex Shank9.5/10View on Amazon - 3
Irwin Tools IRWIN Marples Forstner Bit Set9.4/10View on Amazon - 4
Freud PB-107B: 1/4" to 1" (Dia.)9.3/10View on Amazon
A cabinet door on concealed hinges needs one clean, flat-bottomed hole per hinge cup, and the cup sets the hole size. What size forstner bit for cabinet hinges? Use a 1-3/8 inch bit (34.9 mm), the size that matches a cabinet hinge cup.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

BAIDETS Forstner Bit Set 16Pcs
A 16-piece carbon steel set, 1/4 inch to 2-1/8 inches, with the 1-3/8 inch hinge-cup bit.
Pros
- Includes the 1-3/8 in (34.9 mm) bit for a hinge cup
- 16 pieces to 2-1/8 in, the widest range
- Center tooth keeps positioning precise and stable
- Bevel edge cuts easier, less frictional heat
Cons
- No warranty term is stated
- Shank size is not stated
- 16 pieces run past the hinge job
- No stated bit length

CORTOOL Forstner Bit Set 8Pcs Hex Shank
An 8-piece set, 1/4 inch to 1-3/8 inches, with a 3/8 inch hex shank and the hinge-cup bit.
Pros
- Includes the 1-3/8 in (34.9 mm) bit for a hinge cup
- 3/8 in hex shank resists slipping
- Extra sharp spurs for hard and soft wood
- Flat-bottomed and pocket holes with no chipping
Cons
- No warranty term is stated
- 8 pieces, the smallest set with a stated hinge-cup bit
- Tops out at 1-3/8 in
- No stated weight

Irwin Tools IRWIN Marples Forstner Bit Set
A 14-piece carbon steel set with a reduced shank for 3/8 inch and larger drills; no stated 1-3/8 inch bit.
Pros
- 14 pieces, with 1-1/2, 1-5/8 and 2 in bits named
- Optimized ultra-sharp teeth for hard and soft woods
- Reduced shank fits 3/8 in and larger drills
- Carbon steel for fine woodworking and cabinet-making
Cons
- Whether it includes a 1-3/8 in bit is unstated
- No stated full size list
- Reduced shank fits 3/8 in and larger drills only
- Largest named bit, 2 in, is wider than a hinge cup

Freud PB-107B: 1/4" to 1" (Dia.)
A forged 7-piece set, 1/4 inch to 1 inch, with serrated edges and a limited lifetime warranty; no hinge-cup bit.
Pros
- Forged construction, razor-sharp serrated edges
- Ultra sharp spur for an accurate start
- Steep angled edges for smooth, flat holes, fast chip removal
- Limited lifetime warranty stated
Cons
- Tops out at 1 in, no hinge-cup bit
- 7 pieces, the smallest set here
- Lifetime warranty is a limited tooling warranty
- A hinge-cup buyer needs a separate 1-3/8 in bit
What size forstner bit for cabinet hinges
The short answer is a 1-3/8 inch Forstner bit (34.9 mm): the hinge cup sets the hole size, and that size is the one in the Cortool and BAIDETS sets. The Freud set tops out at 1 inch, and the IRWIN listing does not state a 1-3/8 inch bit, so check the size list. Measure the cup across its widest point, then pick the matching bit.
Check the set before you buy
Measure the cup, then confirm the size list includes the 1-3/8 inch bit. The BAIDETS set lists 16 sizes from 1/4 inch to 2-1/8 inches and the Cortool set 8 sizes from 1/4 inch to 1-3/8 inches, so both state the size plainly. The IRWIN set names only 1-1/2, 1-5/8 and 2 inch bits, so its full range is unclear, and the Freud set states 1/4 inch to 1 inch. Check the shank too: the Cortool set uses a 3/8 inch hex shank, the IRWIN set a reduced shank for 3/8 inch and larger drills, and the Freud set a 1/4 inch to 3/8 inch shank; the BAIDETS set states no shank size.
Forstner bit sets for cabinet hinges
The BAIDETS and Cortool sets state the 1-3/8 inch hinge-cup bit, so match the set to that size first.
FAQ: lasers and CNC
What size Forstner bit do I need for cabinet hinges?
A 1-3/8 inch (34.9 mm) bit. The Cortool and BAIDETS sets include that size; the Freud set tops out at 1 inch.
Does the Freud set include a bit for cabinet hinges?
No. Its 7 bits run from 1/4 inch to 1 inch, so it has no 1-3/8 inch bit.
What shank size do these Forstner bit sets use?
The Cortool set uses a 3/8 inch hex shank, the IRWIN set a reduced shank for 3/8 inch and larger drills, and the Freud set a 1/4 inch to 3/8 inch shank; the BAIDETS set states no shank size.
Can I use these bits in a hand drill?
The BAIDETS set states hand drills, bench drills and floor drills, and the Cortool set states electric power machines and drill presses. The IRWIN set fits 3/8 inch and larger drills. The Freud listing states no drill type.
Which set has the widest range of sizes?
The BAIDETS set, with 16 pieces from 1/4 inch to 2-1/8 inches. The Cortool set has 8 pieces to 1-3/8 inches, the IRWIN set 14, and the Freud set 7 to 1 inch.
Related: the CNC tooling hub, how to use a Forstner drill bit, types of drill bits, drill bit shank types, best router bit for hinge mortise and best router bit for particle board.




