Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

What Is the Best Drill Bit for Hardened Steel?

M35 cobalt twist bits with a 135 degree split point handle hardened steel, and the right set depends on the size range and spares you need.

What Is the Best Drill Bit for Hardened Steel?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Sinyeenglon Cobalt Drill Bits Set for HardenedSinyeenglon Cobalt Drill Bits Set for Hardened9.7/10View on Amazon
  2. 2COMOWARE M35 Cobalt Drill Bit Set for HardenedCOMOWARE M35 Cobalt Drill Bit Set for Hardened9.7/10View on Amazon
  3. 3Cobalt Drill Bit Set - 15Pcs M35 HSS Twist DrillCobalt Drill Bit Set - 15Pcs M35 HSS Twist Drill9.6/10View on Amazon
  4. 4DEWALT Cobalt Alloy Steel Drill Bit Set with PilotDEWALT Cobalt Alloy Steel Drill Bit Set with Pilot9.4/10View on Amazon

Hardened steel dulls an ordinary bit fast, and a bit that skates across the surface leaves a scar instead of a hole. What is the best drill bit for hardened steel? A cobalt steel twist bit with a split point, run slow with cutting fluid, is the answer this guide gives. This guide walks through the cobalt sets, what each figure means, and how to pick a size.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

Only one listing here states a hardness figure or a speed range.

Sinyeenglon Cobalt Drill Bits Set for Hardened

Sinyeenglon Cobalt Drill Bits Set for Hardened

Sinyeenglon9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 99-piece M35 high speed steel twist bit set from 1/16 inch to 3/8 inch, with a hardness figure of up to 67 and a plastic index case.

Pros

  • 99 pieces, with 16 each of 1/16 inch and 5/64 inch
  • M35 steel with hardness up to 67 stated
  • Full per-size count listed, 1/16 inch to 3/8 inch
  • Sizes printed on the lid for quick access

Cons

  • No warranty term is stated on the listing
  • No point angle is stated on the listing
  • Box measures 7.9 by 7.7 by 1.4 inches
  • Shank style is not stated on the listing
COMOWARE M35 Cobalt Drill Bit Set for Hardened

COMOWARE M35 Cobalt Drill Bit Set for Hardened

COMOWARE9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 99-piece M35 cobalt steel twist bit set from 1/16 inch to 3/8 inch, with a 135 degree split point and a partitioned index case.

Pros

  • 99 pieces from 1/16 inch to 3/8 inch
  • 135 degree split point prevents walking on hard surfaces
  • Tri-flat shanks and round shanks in the same set
  • Gold oxide finish reduces friction

Cons

  • No warranty term is stated on the listing
  • No per-size counts are stated
  • No hardness figure is stated
  • No speed range is stated on the listing
Cobalt Drill Bit Set - 15Pcs M35 HSS Twist Drill

Cobalt Drill Bit Set - 15Pcs M35 HSS Twist Drill

SEDIANAS9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 15-piece M35 cobalt steel twist bit set from 1/16 inch to 3/8 inch, with 5% cobalt and a 135 degree split point.

Pros

  • M35 steel with 5% cobalt stated
  • 135 degree split point, self-centering
  • 15 pieces from 1/16 inch to 3/8 inch, with spares at 1/16, 5/64 and 3/32 inch
  • Index storage case with size index

Cons

  • No warranty term is stated on the listing
  • 15 pieces, fewer than the 99-piece sets
  • No hardness figure is stated
DEWALT Cobalt Alloy Steel Drill Bit Set with Pilot

DEWALT Cobalt Alloy Steel Drill Bit Set with Pilot

DEWALT9.4/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 14-piece cobalt alloy steel drill bit set with a Pilot Point, in a connectable storage system with a clear lid.

Pros

  • Cobalt alloy steel with Pilot Point
  • Connectable storage system with bit-bar design
  • Clear lid shows contents at a glance
  • Clip latch for closing

Cons

  • No size range is stated on the listing
  • No point angle is stated, only Pilot Point
  • Hardened steel use is not stated on the listing
  • No warranty term is stated on the listing

What is the best drill bit for hardened steel: cobalt M35

Cobalt steel is the answer the listings point to. The SEDIANAS, Sinyeenglon and COMOWARE sets all use M35 cobalt steel, and the SEDIANAS listing states its M35 steel holds 5% cobalt and gives greater hardness and heat resistance than ordinary bits. The DEWALT set uses cobalt alloy steel without naming M35.

Step 2: Read the point angle

The point helps decide whether the bit bites or walks. The SEDIANAS and COMOWARE listings state a 135 degree split point, which centers the bit and stops it walking on hard surfaces. The Sinyeenglon listing states no point angle, and the DEWALT listing names only a Pilot Point, with no angle in degrees.

Step 3: Match the size range to the job

The SEDIANAS, Sinyeenglon and COMOWARE sets run 1/16 inch to 3/8 inch, in 15, 99 and 99 pieces, and the DEWALT listing states no size range. The Sinyeenglon set holds 16 pieces each at 1/16 inch and 5/64 inch, while the SEDIANAS set holds 2 pieces each at 1/16, 5/64 and 3/32 inch.

Set Pieces Size range Shank
Sinyeenglon 99-Piece 99 1/16 inch to 3/8 inch Not stated
COMOWARE 99-Piece Set 99 1/16 inch to 3/8 inch Round and tri-flat
SEDIANAS 15-Piece Set 15 1/16 inch to 3/8 inch Round straight
DEWALT 14-Piece Set 14 Not stated Not stated

Step 4: Run slow and keep the bit cool

Speed and cooling affect how long a bit lasts. The Sinyeenglon listing advises holding the bit vertical to the work, running at low speed from 200 to 1000 rpm, and using cutting fluid to keep the bit cool and make it last longer. The SEDIANAS and COMOWARE listings state a fully ground twist that clears particles fast. For cutting fluid, see the best aluminum cutting fluid and best metal tapping fluid guides.

Drill bit sets for hardened steel

The sets below handle the drilling step above, so pick the set whose range and spares fit your holes.

Common mistakes to avoid

  • Buying a standard HSS set without cobalt for hardened steel.
  • Skipping the point angle check on the listing.
  • Running the bit fast with no cutting fluid.
  • Ordering a set with no stated size range for a job that needs one.
  • Trusting the spec table size range when the title and bullets say otherwise.

What is the best drill bit for hardened steel: the short version

  1. Pick M35 cobalt steel over standard HSS.
  2. Check for a 135 degree split point on the listing.
  3. Match the 1/16 inch to 3/8 inch range to your holes.
  4. Run at low speed with cutting fluid, as the Sinyeenglon listing advises.
  5. Check the case and the spares.

FAQ: lasers and CNC

What drill bit is best for hardened steel?

A cobalt M35 twist bit with a 135 degree split point.

Is M35 cobalt better than standard HSS for hardened steel?

The SEDIANAS listing states greater hardness and heat resistance than ordinary bits, and COMOWARE states superior heat and wear resistance over standard HSS.

What point angle should a drill bit for hardened steel have?

The SEDIANAS and COMOWARE listings state a 135 degree split point. The Sinyeenglon listing states no point angle, and the DEWALT listing names only a Pilot Point.

What speed should I drill hardened steel at?

The Sinyeenglon listing advises low speed from 200 to 1000 rpm, with the bit vertical to the work and cutting fluid to keep it cool.

How many pieces do the drill bit sets here hold?

The sets here hold 15, 99, 99 and 14 pieces.

Related: the CNC tooling hub, drill bit types chart, drill bit types for metal and our best drill bit for stainless steel guide.

More buying guides

CNC Tooling ·

Best Drill Bit for Stainless Steel (2026)

Five cobalt and step drill bit sets for stainless steel, compared on material, size range, point angle, case and what each listing states.