V Bit vs End Mill for CNC: Which One Should You Buy?
A V bit carves lines and letters with its pointed tip, while an end mill clears slots and pockets: this guide compares the two shapes with four cutters from the listings.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SPEED TIGER ISE Carbide End Mill 1/8”9.8/10View on Amazon - 2
SPEED TIGER EISE 1/8" Carbide Square End Mill9.8/10View on Amazon - 3
Genmitsu 40pcs End Mills CNC Router Bits9.7/10View on Amazon - 4
1Pc 1/8"View on Amazon - 5
EANOSIC 90 Degree V Bit 1/4" ShankView on Amazon - 6
SpeTool 5pcs 30 Degree V Groove Router Bit with TiainView on Amazon - 7
SpeTool 3Pcs Carbide Ball Nose Router Bit CNC End Mill 1/16View on Amazon - 8
Haoruili 10Pcs 1.5mm Carbide End MillView on Amazon - 9
HQMaster Carbide Square End Mill with Nano Blue CoatingView on Amazon
A V bit carves letters, lines and chamfers with its pointed tip, while an end mill cuts slots, pockets and profiles with its end and sides. That is the short answer to v bit vs end mill for cnc: pick the V bit when the groove should taper to a point, and pick the end mill when the cut needs a flat bottom. The four cutters below show each shape at work.
Other machines to compare
1Pc 1/8"Check price on Amazon
EANOSIC 90 Degree V Bit 1/4" ShankCheck price on Amazon
SpeTool 5pcs 30 Degree V Groove Router Bit with TiainCheck price on Amazon
SpeTool 3Pcs Carbide Ball Nose Router Bit CNC End Mill 1/16Check price on Amazon
Haoruili 10Pcs 1.5mm Carbide End MillCheck price on Amazon
HQMaster Carbide Square End Mill with Nano Blue CoatingCheck price on Amazon
This guide explains what each shape cuts and which of the four cutters below fits each job. Listings were collected 10 November 2026.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
V bit vs end mill for CNC: the short answer
A V bit ends in a point, so it draws lines: letters, sign carving, chamfers and decorative grooves. An end mill cuts with its end and sides, so it clears flat-bottomed cuts: slots, pockets and profiles. The four cutters below show the range: one V groove bit and three end mills, an upcut spiral, a 1 mm engraving mill and a tapered ball nose.
What a V bit does
A V bit cuts a V-shaped groove, narrow at the bottom and wide at the top, so the depth of the cut sets the width of the line. The ASNOMY bit here is a 60 degree V groove cutter, and the listing states it for CNC carving and chamfering in wood, plywood, MDF and metals under HRC55. See the best V bits for CNC sign making guide and how to V carve signs on a CNC.
What an end mill does
An end mill cuts with its end and its sides, so it cuts flat-bottomed shapes: slots, pockets, dados and profiles. The SpeTool upcut bit here is a 1/4 in spiral cutter with a 1 in cutting length, and the listing states it for grooves, slots, plunge mortises and dados in wood and plywood. The uxcell set is the fine end of the same idea: a 1 mm cutting edge for engraving PCB, metal, plastics and wood. See the end mill vs V bit for acrylic comparison.
The tapered ball nose: a third shape
A tapered ball nose ends in a rounded tip on a tapered body, so it carves curves and 3D reliefs. The SpeTool set here has a 1.0 mm ball radius, a 2.24 degree single side angle and a 15 mm cutting length, with a TiAlN coating, and the listing states it for 2D and 3D carving in wood, aluminum, alloy copper and acrylic. See the tapered ball nose vs V bit comparison.
Four cutters for the job
The four cutters below are listed in ranked order, from the strongest listing to the weakest.
ASNOMY 60 Degree V Bit
Ranked first. A single 60 degree carbide V groove cutter with a 1/8 in shank, 3 flutes and a 2 in overall length, made of Nano carbide with a TiAlN coating. The listing states it for CNC carving and chamfering in soft and hard wood, plywood, MDF, stainless steel, titanium alloy and other metals under HRC55. No weight, warranty term or safety certification is stated.
SpeTool Tapered Ball Nose
Ranked second. A 5 piece set with 2 flutes, a 1.0 mm ball radius, a 2.24 degree single side angle, a 15 mm cutting length, a 1-1/2 in overall length and a 1/8 in shank, with a TiAlN coating and 55HRC stated. The listing states it for 2D and 3D carving in hard wood, plywood, soft wood, oak, MDF, aluminum, alloy copper and acrylic. No weight, warranty term or safety certification is stated.
SpeTool Upcut Router Bit
Ranked third. A single solid carbide spiral cutter with a 1/4 in shank, a 1/4 in cutting diameter, a 1 in cutting length and a 2-1/2 in total length, stated for grooves, slots, plunge mortises and dados in wood and plywood, on CNC routers and handheld routers with a 1/4 in collet. One point to note: the spec table lists product dimensions of 3.39 inches x 0.51 inches x 6.18 inches, which do not match the stated 2-1/2 in total length, so this article follows the bullets.
uxcell 1mm End Mill
Ranked fourth. A 10 piece set of 1 mm carbide end mills with a 1/8 in shank and a 7 mm cutting edge length, in ultra-fine grain carbide with a titanium coat. The listing states the cutters engrave PCB, circuit boards, metal, plastics, wood, SMT, fiber glass and carbon board, and advises choosing a feed rate and cutting speed to suit the material, without giving figures.
Router bits are sharp cutters. Handle them by the shank, keep fingers clear of the cutting edges, and wear eye protection while the spindle runs.
Common mistakes to avoid
- Using a V bit to clear a pocket. The point cuts a line, not a flat bottom.
- Using an end mill for fine lettering. A flat end leaves rounded inside corners where a V bit leaves a sharp point.
- Skipping the collet check. The cutters here use 1/4 in and 1/8 in shanks.
- Trusting the spec table without reading the bullets. One listing here gives dimensions that do not match its stated total length.
FAQ: lasers and CNC
Can a V bit cut a pocket?
Not well. A V bit cuts a V-shaped groove, so the bottom of the cut is a line, not a flat floor. Use an end mill for pockets.
Can an end mill carve letters?
It can cut letter shapes, but the flat end leaves rounded inside corners and a flat floor, while a V bit leaves a pointed groove.
What is a tapered ball nose end mill for?
3D carving and curves. The SpeTool set here states a 1.0 mm ball radius and a 2.24 degree taper for 2D and 3D carving.
Which shank size do these cutters use?
The upcut bit uses a 1/4 in shank, and the other three use a 1/8 in shank. Check the collet before ordering.
Do these cutters state a warranty?
No. None of the four listings states a warranty term, and none states a safety certification.
Related: CNC tooling, V bit vs engraving bit, chamfer mill vs V bit and CNC router bit types.




