Q Drill Bit Size: Letter Drill Bit Size Chart
A Q bit is a letter-size drill bit in the A to Z series, sitting between P and R, and this guide explains how to find it and use it.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Square Hole Drill Bit9.7/10View on Amazon - 2
Wood Carving Drill Bits Set Compatible with Dremel Rotary9.7/10View on Amazon - 3
toolant Center Drill Bit Set9.7/10View on Amazon
When a plan calls for a q drill bit size, it means a letter Q bit from the A to Z letter drill series. Reach for the letter row of the set, not the fractional row and not the numbered row. This guide explains where Q sits in the letter series, how letter bits differ from fractional and numbered bits, and how to find the Q bit in a set without guessing.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
The listings in this guide name the letter range A to Z but do not print a diameter for the Q bit, so this guide gives no diameter figure for Q. Check the size index on the case or the marking on the shank before drilling.
What a Q drill bit is
A Q drill bit is a letter-size bit, one of the letter sizes that run A to Z. Letter sizes form their own sizing system, separate from fractional sizes such as 1/16 to 1/2 inch and from numbered sizes such as #1 to #60. A letter set holds 26 bits, A to Z, and the Q bit is the letter bit marked Q on its shank. The HIDOTOL letter set keeps its bits in a metal case with a size index holder.
The M35 cobalt letter bits in the listings here are high speed steel with 5% cobalt, built for hard materials. Not every letter set in the listings is M35 cobalt: the Drill America KFD series is high speed steel, and the Drill Hog set is HI-Molybdenum M7 steel. The SEDIANAS and HIDOTOL listings name hardened metal, stainless steel, cast iron, high temperature alloy, titanium alloy, hard plastics and woods. The SEDIANAS, HIDOTOL, and GuardPro cobalt bits (on Amazon) each have a 135° split point with a round straight shank, a self-centering tip that keeps the bit from walking as the hole starts, and a fully ground twist that clears particles and cuts friction and heat.
Where Q sits in the letter series
Letter sizes run A to Z from the smallest letter to the largest, and Q sits between P and R in that run. Each letter is its own size, so P, Q and R are different bits, not names for one size. The letter series fills the gaps between fractional sizes: where a fractional step jumps from one size to the next, the letters give finer steps in between.
That finer step is why plans call for a letter size at all. A fractional bit near Q drills a hole that is looser or tighter than the plan calls for, so the letter bit is the one that matches the plan. The listings here do not print the diameter of Q, so this guide gives no inch figure for it. Read the Q marking on the shank or the size index on the case, and drill with the bit marked Q.
How to find the Q bit in a set
A full set holds all three sizing systems side by side. The 115-piece sets in the listings hold 29 fractional bits from 1/16 to 1/2 inch in 1/64 increments, 26 letter bits from A to Z, and 60 numbered bits from #1 to #60. Look for the letter row in the case: the bits are marked A to Z, and Q follows P.
To find Q, open the letter row and read the markings, then check the shank as well as the case index. The case carries size markings, and the bit shank carries the letter, so check both before drilling. A 26-piece letter set holds the same A to Z run on its own. The HIDOTOL letter set keeps its bits in a metal case with a size index holder, and the Drill America KFD series and the HIDOTOL letter set both list 26 pieces, A to Z.
What to check before you drill
Match the bit to the material. The SEDIANAS and HIDOTOL M35 cobalt listings name hardened metal, stainless steel, cast iron, high temperature alloy, titanium alloy, hard plastics and woods, and the fully ground twist clears particles while it cuts. Check the shank before mounting the bit: a round straight shank fits a wide variety of toolholding systems, and the 135° split point is self-centering, so the bit starts where you place it instead of walking across the surface.
Check the marking twice. The letter Q looks like the letter O on a worn shank, and the numbered bits sit near the letter bits in a full set, so read the shank and the case index together. If the marking is worn past reading, set the bit aside and use a bit whose marking you can read. For stainless steel, our best drill bit for stainless steel guide compares bits for that metal.
Support terms vary by listing. Drill Hog lists a lifetime replacement warranty, GuardPro lists 30-day money back, and SEDIANAS lists a response within 24 hours for questions.
Common mistakes to avoid
- Reaching for a fractional bit when the plan calls for the letter Q.
- Reading the numbered row instead of the letter row in a full set.
- Assuming the nearest fractional size is the same as Q.
- Drilling with a bit whose shank marking you cannot read.
- Matching the bit to the wrong material for the job.
Q Drill Bit Size: The Short Version
- Q is a letter bit in the A to Z series, between P and R.
- Find it in the letter row of the set.
- Check the Q marking on the shank and the case index.
- Match the bit to the material.
- The listings here print no diameter for Q, so check the case index before drilling.
FAQ: lasers and CNC
What size is a Q drill bit?
A Q drill bit is a letter-size bit in the A to Z series, between P and R. The listings in this guide name the letter range but do not print the diameter of Q, so check the size index on the case or the marking on the shank. This guide gives no diameter figure for Q.
Is a Q drill bit bigger than a P drill bit?
Yes. Letter sizes run A to Z from the smallest letter to the largest, so Q is larger than P and smaller than R. Each letter is its own size, so a P bit and a Q bit drill different holes.
What is a letter drill bit set?
A letter drill bit set holds the letter sizes A to Z, 26 bits. The HIDOTOL letter set keeps its bits in a metal case with a size index holder. The HIDOTOL letter set and the Drill America KFD series both list 26 pieces, A to Z, and full 115-piece sets hold the same 26 letter bits alongside fractional and numbered bits.
How do I find the Q bit in a 115-piece set?
The 115-piece sets hold 29 fractional bits from 1/16 to 1/2 inch, 26 letter bits from A to Z, and 60 numbered bits from #1 to #60. Look for the letter row in the case, read the markings A to Z, and pick the bit marked Q. Check the shank marking as well as the case index.
What materials can a Q drill bit cut?
That depends on the bit. The SEDIANAS and HIDOTOL M35 cobalt listings name hardened metal, stainless steel, cast iron, high temperature alloy, titanium alloy, hard plastics and woods. The 135° split point is self-centering, and the fully ground twist clears particles while it cuts.
Can I use a fractional bit instead of a Q bit?
A fractional bit near Q is a different size, so it drills a hole that is looser or tighter than the plan calls for. Letter sizes fill the gaps between fractional steps, so the letter bit is the one that matches the plan. Check the plan before swapping sizes.
Related: the CNC tooling hub, our best drill bit sharpener for home use guide and the best countersink drill bit set for wood. Also see our best CNC router bits.




