How to Use Heat Set Inserts
How to use heat set inserts: pick the right size, heat the tip, press the insert straight into the printed hole, and let the plastic cool around the threads for a strong, reusable connection.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Vertical Heat Set Insert Tool with 90W Soldering9.5/10View on Amazon - 2
Paltren 21-in-1 3D Printer Smoothing Tool Kit9.5/10View on Amazon - 3
580+7PCS Heat Set Threaded Inserts Kit9.5/10View on Amazon - 4
FFVRVSS Heat Set Insert Tool 7X Soldering Tips9.5/10View on Amazon
Heat set inserts turn brittle printed threads into durable metal connections that survive repeated assembly. A printed part with a brass insert accepts the same screw again and again, which suits enclosures, drone frames and parts that come apart for service. Learning how to use heat set inserts takes a matching tip, a steady press and a little patience, and the steps below cover each part.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Vertical Heat Set Insert Tool with 90W Soldering
A 90W vertical press tool with a linear rail slider, a 210mm working height and a real-time digital temperature display.
Pros
- 90W iron with a real-time digital temperature display
- Linear rail slider with a 210mm working height
- Adjustable fixture holds parts at different heights
- Built-in drawer and cord management
Cons
- Insert sizes are not stated in the listing
- No insert count is stated
- Insert work only, with no smoothing tips listed
- No warranty term is stated

Paltren 21-in-1 3D Printer Smoothing Tool Kit
An 80W iron kit with 7 brass insert tips from M2 to M8, 9 smoothing tips, a safety stand and a digital display reading 180°C to 500°C.
Pros
- 80W iron with an LED digital display, 180°C to 500°C
- 7 brass insert tips covering M2 to M8
- 9 smoothing tips, a sponge and 2 sanding sticks
- Safety stand and anti-slip silicone sleeve
Cons
- No warranty term is stated
- 21 pieces need the stand and storage
- No temperature setting per filament is stated
- Hand-held seating depends on a steady hand

580+7PCS Heat Set Threaded Inserts Kit
A 580+ piece brass insert kit in 6 sizes from M2 to M6, with a heat set insert tool and labelled compartments.
Pros
- 580+ brass inserts across 6 sizes, M2 to M6
- 45-degree spiral knurling for grip
- Heat set insert tool with an extended tip
- Separate labelled compartments for each size
Cons
- No M8 inserts in the set
- No soldering iron is included
- Brass only, no steel option listed
- No temperature guidance is stated

FFVRVSS Heat Set Insert Tool 7X Soldering Tips
A set of 7 CNC-machined brass tips from M2 to M8 with a 900M/T18 adapter and a clear storage case.
Pros
- 7 CNC-machined brass tips covering M2 to M8
- Slim-neck design reaches deep recesses
- Split threaded design swaps sizes in seconds
- Fits 900M/T18 heads, including Hakko and Weller
Cons
- Tips only, no soldering iron included
- No insert pieces are included
- Adapter fits 900M/T18 heads only
- No smoothing tips in the set
How to Use Heat Set Inserts Step by Step
Start with the screw the part needs, then match the insert to that thread. Insert sizes here run from M2 to M8: the Paltren and FFVRVSS tips (on Amazon) cover M2 to M8, and the Susksdr set covers M2 to M6, so the thread size decides both the insert and the tip. The FFVRVSS tips are CNC-machined from brass for a dimensional fit, and the slim neck reaches deep recesses without touching nearby walls.
Fit the tip to the iron next. The FFVRVSS tips use a 900M/T18 adapter and fit heads such as the Hakko FX-888D, FX-600, Weller WLC100, SP40NUS and Yihua, and the split threaded design swaps sizes in seconds with no tools. The Paltren and Mintion kits include the iron, so the 900M/T18 adapter is not needed there.
Heat the iron and let the display hold steady before seating an insert. The Paltren iron (on Amazon) reads from 180°C to 500°C, or 356°F to 932°F, on its LED digital display. For general guidance on iron settings, see the soldering temperature guide.
Set the insert on the hot tip, line it up over the printed hole and press it straight down until it seats. The Mintion tool runs the iron down a linear rail slider, which keeps the press straight, and its adjustable fixture holds parts at different heights.
Hold the insert in place while the plastic cools and grips the knurling, then lift the iron straight off. The Susksdr inserts (on Amazon) use 45-degree spiral knurling, and the knurled exterior creates tight friction with the plastic. Once the part is cool, fit the screw and check that the thread turns freely.
The Gear for Heat Set Inserts
Four kits cover this job, from a vertical press tool to a 580+ piece insert set.
Heat Set Insert Tips
Good results come from matching the tip to the insert and keeping the setup tidy. Keep a cleaning sponge nearby for melted plastic on the tip; the Paltren kit includes a high-temp cleaning sponge for that job. Store tips and inserts where each size is easy to find: the FFVRVSS set ships in a clear storage case, the Susksdr inserts sit in labelled compartments, and the Mintion tool has a drawer.
Match the kit to the filament as well as the size. The FFVRVSS tips suit PLA, PETG, ABS and ASA, the Mintion tool suits PLA, ABS, PETG and other filament types, and the Susksdr inserts work with PLA, PETG, ABS, PPS and PP.
FAQ: lasers and CNC
What size heat set insert do I need?
Match the insert to the screw thread the part needs. The Paltren and FFVRVSS tips cover M2 to M8, and the Susksdr set covers M2 to M6. For the hole size behind a common thread, see the M4 heat set insert hole size chart.
Which plastics work with heat set inserts?
The listings name PLA, PETG, ABS and ASA for the FFVRVSS tips, PLA, ABS and PETG for the Mintion tool, and PLA, PETG, ABS, PPS and PP for the Susksdr inserts.
Do I need a special soldering iron for heat set inserts?
Not always. The FFVRVSS tips fit 900M/T18 heads, including the Hakko FX-888D, FX-600, Weller WLC100, SP40NUS and Yihua, so a compatible iron works with the adapter. The Paltren kit includes an 80W iron and the Mintion tool includes a 90W iron, so those kits need no separate iron.
What comes in a heat set insert kit?
It varies by kit. The Paltren set includes the iron, 7 insert tips, 9 smoothing tips, an adapter, a stand, a sponge and 2 sanding sticks. The Mintion kit holds inserts, adapter tips, tweezers, a hex wrench and a drawer. The Susksdr kit holds 580+ inserts and a tool, and the FFVRVSS set holds 7 tips, an adapter and a case.
How do I keep a heat set insert straight?
Press the insert straight down and keep the iron level while it seats. The Mintion tool runs the iron down a linear rail slider with a 210mm working height, which keeps the press straight on larger parts. With a hand iron, the FFVRVSS slim-neck tip reaches the hole without touching nearby walls.
Related: the CNC tooling hub, M4 heat set insert hole size chart and how to use a soldering tool. Also see the best soldering iron kit. Also see the best soldering iron for beginners.




