M5 Heat Set Insert Hole Size Chart
The hole for an M5 heat set insert matches the insert, so this guide shows the temperatures, press times and kits that seat M5 inserts flush.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
607Pcs Threaded Inserts for Plastic9.5/10View on Amazon - 2
Preciva Threaded Inserts Set9.5/10View on Amazon - 3
3DZWMAN Vertical Heat Set Insert Tool9.5/10View on Amazon - 4
Preciva Threaded Inserts Set9.5/10View on Amazon
A printed part with an M5 thread needs a hole that matches the insert, and the m5 heat set insert hole size comes from the insert maker rather than from a shop rule. The makers behind the kits below publish no hole diameter for M5 inserts, so the size to drill or print comes from the M5 insert maker’s own spec. The sections below show the temperatures and times the makers give, and the mistakes that waste a print.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
| # | Product | HQ Score | Buy |
|---|---|---|---|
| 1 | 607Pcs Threaded Inserts for Plastic | 9.5/10 | Buy on Amazon |
| 2 | Preciva Threaded Inserts Set | 9.5/10 | Buy on Amazon |
| 3 | 3DZWMAN Vertical Heat Set Insert Tool | 9.5/10 | Buy on Amazon |
| 4 | Preciva Threaded Inserts Set | 9.5/10 | Buy on Amazon |

607Pcs Threaded Inserts for Plastic
A 607-piece brass insert kit with 6 sizes from M2 to M6, 6 soldering tips, and stated temperatures and times for PLA and ABS.
Pros
- 607 pieces in 6 sizes from M2 to M6, including M5
- Brass inserts with a 45° spiral knurl for torque and pull-out strength
- 180-230°C for PLA and 230-280°C for ABS
- Press 3-8 seconds until flush, then cool 30-60 seconds
Cons
- Soldering iron not included
- Sizes run M2 to M6 only
- The inserts are brass, with no other insert material in the kit
- No temperature control comes with the kit

Preciva Threaded Inserts Set
A 750-piece kit with a 60W digital soldering iron, 5 insert tips from M2 to M6, a holder and tweezers for 3D printer parts or plastic parts.
Pros
- 750 pieces: 192 inserts, 194 bolts, 182 nuts and 182 washers
- 60W digital soldering iron, 200-500°C
- 5 insert tips from M2 to M6 with a split design for tip changes
- Holder and tweezers included for safer operation
Cons
- No warranty term is stated
- Sizes run M2 to M6 only
- No M2.5 tip, so that size needs another kit
- Made for plastic parts

3DZWMAN Vertical Heat Set Insert Tool
A vertical heat set insert press with a 2040 aluminum profile frame, a digital soldering iron at 180-500°C, and tips from M2 to M8.
Pros
- Tips cover M2, M2.5, M3, M4, M5, M6 (1/4) and M8
- Digital soldering iron, 180-500°C, 110V/220V
- Widened 2040 aluminum profile frame, three V-shaped pulleys
- Silicone protective cover and anti-slip foot pads included
Cons
- No warranty term is stated
- A press tool, with no threaded inserts in the set
- The frame measures 10.16 x 1.97 x 11.69 inches, so it needs bench space
- Tips fit ceramic tube D4xL24 soldering irons

Preciva Threaded Inserts Set
A 716-piece kit with a 60W digital soldering iron, 5 insert tips from M2 to M6, a holder and tweezers for 3D printer parts or plastic parts.
Pros
- 716 pieces: 179 inserts, 179 bolts, 179 nuts and 179 washers
- 60W digital soldering iron with 5 insert tips from M2 to M6
- Split design for tip changes without unscrewing the iron sleeve
- Holder and tweezers included
Cons
- Sizes run M2 to M6 only
- No M2.5 tip, so that size needs another kit
- Made for plastic parts
- 179 threaded inserts, fewer than the 192 in the 750-piece kit
M5 heat set insert hole size: the short answer
An M5 insert seats in a hole sized to the insert, and the hole size comes from the insert maker’s spec for that M5 insert. The insert kits below carry M5 inserts with matching M5 tips, and the press below carries an M5 tip. For PLA, the Nefuree kit gives 180-230°C, and for ABS it gives 230-280°C, with a press of 3-8 seconds until flush and a cool of 30-60 seconds.
How to seat an M5 insert
Start with the M5 tip on the iron or press, and set the temperature for the plastic. For PLA, the Nefuree kit gives 180-230°C, and for ABS it gives 230-280°C. The Preciva 750-piece kit runs its 60W iron at 200-500°C, and the 3DZWMAN press runs its iron at 180-500°C.
Press the tip against the insert for 3-8 seconds until it sits flush, then let it cool for 30-60 seconds. Those times come from the Nefuree kit. Tip changes on the Preciva kits use a split design, so a tip swaps without unscrewing the sleeve of the iron, and the 3DZWMAN press adjusts insertion height by hand.
Gear for M5 heat set inserts
The M5 tip and the M5 inserts in these kits handle the heating and pressing step, so the gear below is picked for that step.
Common mistakes to avoid
- Drilling or printing the hole to a guessed size instead of the insert maker’s spec for the M5 insert.
- Heating past the Nefuree kit’s temperature for the plastic: 180-230°C for PLA and 230-280°C for ABS.
- Pressing past 8 seconds, or moving the insert before 30-60 seconds of cooling, against the Nefuree kit’s stated times.
- Fitting an M5 insert with a tip of another size.
- Setting a hot iron down with no holder.
M5 heat set insert hole size: the short version
- Match the hole to the M5 insert maker’s spec.
- Fit the M5 tip for the M5 insert.
- Heat to the maker’s temperature for the plastic.
- Press for 3-8 seconds until flush, as the Nefuree kit states.
- Cool for 30-60 seconds before handling the part, as the Nefuree kit states.
FAQ: lasers and CNC
What hole size does an M5 heat set insert need?
The kits below publish no hole diameter for M5 inserts, so the size comes from the M5 insert maker’s own spec. The hole matches the insert, and the M5 inserts and M5 tips below cover the M5 size.
What temperature does an M5 insert need in PLA?
The Nefuree kit gives 180-230°C for PLA, with a press of 3-8 seconds and a cool of 30-60 seconds.
What temperature does an M5 insert need in ABS?
The Nefuree kit gives 230-280°C for ABS, with a press of 3-8 seconds and a cool of 30-60 seconds.
How long should an M5 insert be pressed and cooled?
Press for 3-8 seconds until the insert sits flush, then cool for 30-60 seconds. Those times come from the Nefuree kit, which states the install method in full.
Do these kits include an M5 tip?
Yes. The Preciva kits include 5 insert tips from M2 to M6, the Nefuree kit includes 6 soldering tips from M2 to M6, and the 3DZWMAN press includes tips from M2 to M8. An M5 tip is in every kit here.
Related: the CNC tooling hub, M4 heat set insert hole size, M3 heat set insert hole size and best heat press inserts.




