Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

DTF Printer Troubleshooting: Common Fixes

A step-by-step guide to DTF printer troubleshooting: read the print, check the nozzles, clean the printhead and clear white ink clogs before the next print run.

DTF Printer Troubleshooting: Common Fixes
On this page

DTF printer troubleshooting starts with the print in front of you, not with a new part. A faded print, horizontal stripes, missing colors or an incomplete pattern point to a clogged printhead, and white ink crystallization sits behind many of those blocks. This guide works through the fault in order: read the print, check the nozzles, clean the printhead, then look at ink and film. Each step uses the cleaning kits and machines the makers list for DTF printers.

As an Amazon Associate I earn from qualifying purchases. LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

This guide gives no fix rates or success percentages. Kit sizes, contents and machine figures below come from the makers’ own listings, and any figure that is not published is left out rather than guessed.

Step 1: Read the fault in the print

Start by naming what the print shows. Incomplete patterns, horizontal stripes and faded prints point to nozzles that are blocked or partly blocked. Missing colors and color shifts point to an ink channel that is not flowing, and blurred output points to a printhead that needs cleaning. White ink deserves a close look first: dried white ink and white ink crystallization block nozzles and sit behind a large share of print quality faults. For background on how a DTF print comes together, see how DTF transfer works.

Step 2: Run a nozzle check and the printer cleaning cycle

Use the printer’s own nozzle check to see which nozzles are blocked, then run the printer’s built-in cleaning cycle and check the pattern again. The check shows the fault as a gap or a stripe in the printed pattern, and the cleaning cycle pushes ink through the nozzles to clear dried ink. If stripes or missing colors stay after the built-in cleaning, move on to a manual clean with a cleaning kit rather than repeating the cycle again and again.

Step 3: Clean the printhead with a cleaning kit

A cleaning kit gives the tools for a manual clean: solution and tubing, with most kits adding a syringe and nozzles that fit the ink ports. The NGOODIEZ kits hold 100mL or 250mL of solution in a 7-piece kit with a precision syringe, silicone tubing, 2 white nozzles, 1 yellow nozzle, an L-shaped tube and a foam swab. The CenDale kit (on Amazon) holds 150mL with a 10mL precision syringe, a 10cm cleaning tube, a yellow nozzle, a white nozzle, 2 L-shaped tubes, 4 cotton swabs and 1 pair of gloves. The Fynqil kit (on Amazon) holds 100mL with 2 orange nozzle tips, 5 syringes, 10 cleaning swabs, 6 cleaning tubes and a lint-free cleaning cloth. The OMTech kit (on Amazon) holds 16.9 fl oz of solution with a graduated bottle, cleaning cartridges and tubing. Follow the instructions that come with the kit, and keep solution off the motherboard and internal cables. For routine care, see DTF printer maintenance.

Step 4: Clear a stubborn white ink clog

When a kit clean does not clear the fault, a printhead cleaning machine adds heat and a pump. Its heater warms cleaning solution to 86 to 104 degrees Fahrenheit, which helps dissolve blockages, and it flushes forward and in reverse so debris is pulled out from the upper side instead of being pushed deeper into the nozzles. A built-in timer sets running and stop times from 1 second to 99 hours, and cleaning pressure adjusts up to a maximum flow of 100 mL/min. Adjustable holders fit printheads from small desktop models to industrial wide-format heads. The YUNMOKH washer (on Amazon) is sold for light clogs only, and a heavy clog cannot be repaired completely, so do not use too much pressure and do not expect a washer to save a printhead that is badly blocked. For an XP600 printhead on the washer, the damper manifold must change to the normal type.

Step 5: Check ink, film and the rest of the path

If the printhead is clean and the fault stays, look past the printhead. Check that each ink line carries ink to the head and that the dampers sit as the printer maker directs. Look at the film for creases or marks, and check that the powder covers the printed area evenly before pressing. The set-up guide at DTF printer set up covers film, ink and powder. When the fault follows a single color only, work through that color’s line from the bottle to the nozzle before touching the other colors.

Common mistakes to avoid

  • Going straight to a manual clean without a nozzle check to name the fault.
  • Pushing cleaning solution through with too much pressure.
  • Letting solution reach the motherboard or internal cables.
  • Expecting a washer to repair a heavy clog that the maker states cannot be repaired completely.
  • Leaving the printer idle for long stretches with no maintenance, then expecting a first print to come out clean.

DTF printer troubleshooting: the short version

  1. Read the print and name the fault: stripes, faded colors, missing colors or an incomplete pattern.
  2. Run a nozzle check and the printer cleaning cycle, then check the pattern again.
  3. Clean the printhead with a cleaning kit, keeping solution off the motherboard and cables.
  4. For a stubborn white ink clog, use a heated cleaning machine with a forward and reverse flush.
  5. Check ink lines, dampers, film and powder when the printhead is clean and the fault stays.
  6. Print a small design and look at the colors before going back to full work.

Everything after that is repetition: clean on a schedule, watch the first print after a pause and fix the fault at the printhead before changing anything else.

FAQ: lasers and CNC

Why does my DTF printer print faded colors?

Faded colors point to nozzles that are partly blocked, and white ink crystallization is a common cause. Run a nozzle check, then a cleaning cycle, and move to a manual clean with a cleaning kit if the colors stay faded. The kit solution dissolves dried ink and restores nozzle flow.

What causes horizontal stripes in DTF prints?

Horizontal stripes come from nozzles that are blocked or partly blocked, so some rows of the pattern do not print. A nozzle check shows the gap, and a cleaning cycle or a manual clean with a cleaning kit clears the dried ink. If stripes stay after cleaning, work through the steps for a stubborn white ink clog.

How do I clean a clogged DTF printhead?

Use a cleaning kit with solution, a syringe, tubing and nozzles that fit the ink ports. Kit sizes run from 100mL to 500mL, and a kit holds 16.9 fl oz with a graduated bottle. Follow the instructions that come with the kit, and keep solution off the motherboard and internal cables.

Can a cleaning machine clear a heavy clog?

No. The YUNMOKH washer is sold for light clogs only, and a heavy clog cannot be repaired completely, so there is no promise of success. Use the washer for light blockages and for regular maintenance, and do not push solution through with too much pressure.

Which printers do DTF cleaning kits fit?

The kits fit Epson L1800, R1390 and XP-600. Most also list the ET-8550 and XP-15000, and several list the L805 and modified systems built on i3200, DX5, XP600 and 4720 printheads. Match the kit to the printhead in the printer, and check the nozzle fit before starting a clean.

What is in a DTF printhead cleaning kit?

A 7-piece kit holds a bottle of cleaning solution, a precision syringe, silicone tubing, 2 white nozzles, 1 yellow nozzle, an L-shaped tube and a foam swab. Other kits add cotton swabs, gloves, extra syringes and cleaning tubes, and a kit adds a lint-free cleaning cloth.

Related: the craft machines hub, how to use DTF transfer film and heat press temperature for DTF. Also see the best DTF powder for heat press, the best DTF transfer film and how to make a DTF transfer.

More buying guides

Craft Machines ·

How to Use DTF Printer: Step by Step

Print the design on DTF film with DTF ink, coat it with powder, heat-set the print and press it onto fabric: a step-by-step guide…

Craft Machines ·

Low Cost DTF Printer: What to Buy (2026)

A low cost DTF printer guide comparing print width, printhead, white ink circulation, bundle contents, ink supply and warranty terms for apparel work.

Craft Machines ·

DTF Printer Sizes: Bed Dimensions Guide

This guide covers A3 and A3+ DTF printer sizes, and the size to pick is the one whose stated print width covers your largest…