How to Use DTF Printer: Step by Step
Print the design on DTF film with DTF ink, coat it with powder, heat-set the print and press it onto fabric: a step-by-step guide with film, ink and kit picks.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Printium DTF Ink White 16.9 fl oz (500ml)9.6/10View on Amazon - 2
Jecqbor DTF Transfer Film Roll 24" x 328 FT9.5/10View on Amazon - 3
Procolored Direct to Transfer Film Ink9.5/10View on Amazon - 4
A-SUB DTF Transfer Film and Powder Kit9.4/10View on Amazon
How to use DTF printer comes down to a short chain of steps: print the design onto special film with DTF ink, coat the wet print with adhesive powder, heat the powder until it bonds to the ink, then press the film onto fabric and peel it away. The picks below cover film, white ink, a full ink set and a starter kit.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
This guide gives no press temperatures or times, because the listings state none. Follow the settings the makers of your film, powder and press list.

Printium DTF Ink White 16.9 fl oz (500ml)
A 16.9 fl oz (500ml) bottle of white DTF ink with a high-opacity formula for dark and light garments, for DTF and converted DTG printers.
Pros
- High-opacity white covers in a single pass, as the maker states
- Works with I3200, XP600, TX800, 4720, DX5, DX7, I1600 and I390 printheads
- ICC profiles included for color output
- Water-based, odorless and non-toxic formula
Cons
- White ink only: colors are bought separately
- The maker says to shake once before use so pigments stay suspended
- No warranty term is stated
- Suits printers on the compatibility list; others are not listed

Jecqbor DTF Transfer Film Roll 24" x 328 FT
A 24 in x 328 ft double-sided matte PET film roll with a 12-layer coating, anti-static treatment and anti-curl design for DTF inkjet printers.
Pros
- 12-layer coating helps ink absorb evenly for vivid color and sharp detail
- Anti-static treatment and anti-curl design help the roll feed smoothly with fewer jams
- Hot peel suits batch orders, while cold peel suits fine lines and detailed artwork
- Works on light and dark cotton, polyester, blends, canvas and denim
Cons
- Film only: ink, powder and a heat press are bought separately
- Results depend on matching ink, powder and heat press settings
- A 328 ft roll is a large supply for occasional single-shirt jobs
- The 24 in roll width needs a printer that takes wide film

Procolored Direct to Transfer Film Ink
A 6-bottle DTF ink set with 500ml white ink, plus yellow, cyan, black and magenta, for DTF and 6/8-color Procolored printers.
Pros
- Six bottles cover white plus yellow, cyan, black and magenta in a single order
- ICC profile available for color output
- Lists compatibility with L1800, L805, R1390, ET8500, ET8550 and other Epson-based printers
- A 30-day warranty is stated in the listing
Cons
- Made for DTF and Procolored printers; other types are not listed
- Film, powder and a heat press are bought separately
- The 30-day warranty covers a short window
- No powder or film included, so a first setup needs more supplies

A-SUB DTF Transfer Film and Powder Kit
A DTF starter kit with 30 A4 film sheets, 17.6 oz of white medium powder and a roll of heat-resistant tape for DTF and sublimation printers.
Pros
- A single kit covers film, powder and tape for a first DTF setup
- 30 A4 sheets suit small designs and short runs
- Matte finish and anti-static coating help ink absorb for vivid, true-to-color prints
- Powder bonds designs that withstand repeated washing without peeling, as the maker states
Cons
- A4 sheets suit small designs, not wide prints
- The sublimation route works only on light-colored fabrics; dark fabrics need DTF ink
- No warranty term is stated
- Powder is 1.1 lb, a small supply for large batch work
How to use DTF printer, step by step
DTF printing moves a design from film to fabric: the printer lays DTF ink on coated PET film, adhesive powder grips the wet ink, heat bonds the powder and ink, and a heat press moves the finished design onto the fabric. Get each link right and the print stays flexible and survives washing; miss a link and the design peels or cracks.
Step 1: Load DTF ink and set up the printer
A DTF setup needs DTF ink, not standard printer ink. White ink lays down the opaque base dark garments need, while yellow, cyan, black and magenta carry the color. Both inks below list ICC profiles for consistent color output. Shake the white ink once before use, as the Printium listing says, so pigments stay suspended.
Step 2: Print the design onto DTF film
Print onto coated matte film, not plain paper. The Jecqbor roll below is a double-sided matte PET film with a 12-layer coating, anti-static treatment and an anti-curl design, which helps the film feed flat with fewer jams and helps ink absorb evenly. A4 sheets suit small designs and short runs; a 24 in wide roll suits wide designs and repeated runs.
Step 3: Coat the wet print with powder
While the ink is still wet, coat the print with adhesive powder so it grips the ink. The A-SUB kit below includes 1.1 lb of white medium powder plus a roll of heat-resistant tape. Spread the powder evenly and shake off the loose powder: the powder bonds the design to the fabric, so a print pressed without powder will not hold.
Step 4: Heat-set the powder and press the transfer
Heat the powdered print until the powder melts and bonds to the ink, then lay the film on the fabric and press it. The heat press temperature for DTF transfers guide covers press settings, and the what is a DTF oven guide explains the usual way to heat-set powder evenly. Keep the workspace ventilated.
Step 5: Peel the film and check the print
Peel the film from the fabric once the press cycle is done. The Jecqbor film below supports hot peel, which suits batch orders because there is no wait after pressing, and cold peel, which suits fine lines and detailed artwork. Check the edges after peeling: lifted edges mean the press step needs another look.
The gear for printing DTF transfers
The steps above need film, ink and powder, and the four picks below cover each of those jobs, ranked by HQ Score.
Common mistakes to avoid
- Using a sublimation setup on dark fabric without DTF ink: that route works only on light-colored fabrics.
- Buying a 24 in roll for a printer that only takes small sheets, or A4 sheets for wide designs.
- Forgetting to shake white ink before use, so pigments settle and the white base prints thin.
- Pressing a print with no powder on it, so the design has nothing to bond it to fabric.
- Guessing press settings instead of following the makers’ settings.
How to use DTF printer: the short version
- Load DTF ink, white plus color, and the ICC profiles the maker supplies.
- Print the design onto coated matte DTF film.
- Coat the wet print with adhesive powder.
- Heat the powder until it bonds to the ink.
- Press the film onto the fabric with a heat press.
- Peel hot for batch work or cold for fine lines, then check the edges.
Everything after that is repetition: keep the film flat, the ink shaken and the powder even.
FAQ: lasers and CNC
Can I use a DTF printer on dark fabric?
Yes, because white ink lays down an opaque base under the color. The film and ink in this guide list cotton, polyester, blends, canvas and denim. Dark fabrics need DTF ink: a sublimation setup alone will not carry a design onto a dark shirt.
What supplies do I need to start DTF printing?
Film, DTF ink, adhesive powder and a heat press. The A-SUB kit in this guide bundles 30 A4 film sheets, 1.1 lb of white medium powder and a roll of heat-resistant tape. Ink is bought separately: white ink plus yellow, cyan, black and magenta.
What is the difference between hot peel and cold peel?
Hot peel means peeling right after pressing, which suits batch orders because there is no wait between shirts. Cold peel means letting the transfer cool before peeling, which suits fine lines and detailed artwork. The Jecqbor film in this guide supports both.
Can I use a sublimation printer for DTF printing?
A sublimation printer can work with a DTF film and powder kit: the A-SUB kit lists compatibility with most DTF and sublimation printers. The limit is color: the sublimation route suits light-colored fabrics only, and dark fabrics need DTF ink.
How much film do I need for a shirt?
A single A4 sheet covers a small design, which is why the A-SUB kit ships 30 A4 sheets for short runs. A 24 in x 328 ft roll suits repeated runs and wide designs.
Related: the craft machines hub, how DTF transfer works and DTF printer troubleshooting. Also see the best T shirt heat press machine guide.




