Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Drill Bit Chart: Numbers, Letters and Fractions

A drill bit chart maps fractional, number and letter markings to hole sizes, and this guide shows how to read it and match the bit to the material.

Drill Bit Chart: Numbers, Letters and Fractions
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1DEWALT Drill Bit Set, 3-Flats Shank,14-PieceDEWALT Drill Bit Set, 3-Flats Shank,14-Piece9.6/10View on Amazon
  2. 2COMOWARE Titanium Twist Drill Bit Set 16 PcsCOMOWARE Titanium Twist Drill Bit Set 16 Pcs9.6/10View on Amazon
  3. 3CRAFTSMAN 14-Piece Gold Oxide Drill Bit SetCRAFTSMAN 14-Piece Gold Oxide Drill Bit Set9.6/10View on Amazon

A drill bit chart turns a size marking into the hole the bit will cut. Fractions, numbers and letters are separate sizing systems, and the chart lines the systems up side by side, so a marking from any system reads as a size and the bit in the chuck matches the hole the job needs. This guide explains how to read the chart, how to match the bit to the material, and which sets carry marked sizes or a size index.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

A full number-to-size conversion table is not printed here, because the listings in this guide state only the sizes in the sets below. Read the size from the marking on the bit shank or the size index in the holder, and match it to the hole the job needs.

DEWALT Drill Bit Set, 3-Flats Shank,14-Piece

DEWALT Drill Bit Set, 3-Flats Shank,14-Piece

DEWALT9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 14-piece high speed steel set with a 135 degree split point, a tapered web, and a 3-flats shank, for plastic, wood and metal.

Pros

  • 135 degree split point tip helps reduce walking
  • High speed steel for plastic, wood and metal
  • Tapered web for durability and resisting breakage
  • Size markings on the shank for quick identification

Cons

  • No warranty term is stated
  • 3-flats shank only on sizes larger than 3/16 inch
  • No storage case is stated
  • No list of the 14 sizes is stated
COMOWARE Titanium Twist Drill Bit Set 16 Pcs

COMOWARE Titanium Twist Drill Bit Set 16 Pcs

COMOWARE9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 16-piece titanium-coated high speed steel set from 1/16 to 1/4 inch, with a 1/4 inch hex shank, 2 flutes, and a holder with a size index.

Pros

  • Stated size range from 1/16 to 1/4 inch in 16 pieces
  • 1/4 inch hex shank locks into a quick change chuck
  • Titanium coating on high speed steel for capability and durability
  • Holder with a size index for easy storage and organizing

Cons

  • No warranty term is stated
  • No split point is stated for precise placement
  • No weight is stated
  • No list of the 16 sizes is stated beyond the range
CRAFTSMAN 14-Piece Gold Oxide Drill Bit Set

CRAFTSMAN 14-Piece Gold Oxide Drill Bit Set

CRAFTSMAN9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 14-piece gold oxide set with a split point for precise hole placement and clean, burr-free holes in wood, plastic or metal.

Pros

  • Gold oxide coating promotes longer life
  • Split point for precise hole placement and clean, burr-free holes
  • Carrying case for compact and durable storage
  • 14 pieces for wood, plastic or metal

Cons

  • No warranty term is stated
  • The listing calls the case metal and plastic in the same bullet
  • No size list is stated for the 14 pieces
  • No split point angle is stated

How to read a drill bit chart

A drill bit chart lists bit sizes in rows, with each row giving the marking and the diameter it stands for. Fractional sizes are written as fractions of an inch, number sizes are written as plain numbers, and letter sizes are written as letters, and the chart lines the systems up side by side so a marking from any system can be read as a size. The DEWALT listing notes size markings on the drill bit shank for identifying sizes quickly. Read the marking before the bit goes in the chuck, and keep the chart near the bench while the set is open.

Match the bit to the material

The DEWALT and COMOWARE listings state high speed steel, and the CRAFTSMAN listing states a gold oxide coating with no base material named. The DEWALT and CRAFTSMAN sets list plastic, wood and metal, and the COMOWARE set lists wood, plastic and aluminum alloy. The DEWALT set lists high speed steel for plastic, wood and metal, with a tapered web for durability and a black and gold coating to help prevent rust and wear. The CRAFTSMAN set lists a gold oxide coating for corrosion resistance and a split point for precise hole placement and clean, burr-free holes. The COMOWARE set lists high speed steel with a titanium coating for wood, plastic and aluminum alloy, with 2 flutes to clear chips and debris away from the bit. Match the coating and the point to the material, and let the chart settle the size.

Drill bit sets for the chart

The chart is only useful with bits whose sizes are marked and easy to find. The DEWALT set marks sizes on the shanks and the COMOWARE holder carries a size index, and the sets below carry the shanks the chart points to.

Pick the right size from the chart

Start from the hole the job needs, then find the marking on the chart that stands for that size. The COMOWARE set covers 1/16 to 1/4 inch in 16 pieces, with a size index in the holder, so the size can be checked before the bit leaves the case. The DEWALT and CRAFTSMAN sets hold 14 pieces each, with size markings on the DEWALT shanks for quick identification. Check the shank as well as the size: the DEWALT 3-flats shank reduces spin-out in the chuck on sizes larger than 3/16 inch, and the COMOWARE 1/4 inch hex shank locks into a quick change chuck. A bit that fits the chuck and matches the chart marking is the bit to use.

Common mistakes to avoid

  • Reading the marking as the wrong system: number sizes and fractional sizes sit side by side on the chart, so read the row the marking comes from.
  • Guessing the size instead of reading the marking on the shank or the size index in the holder.
  • Ignoring the shank: the DEWALT 3-flats shank and the COMOWARE hex shank seat in the chuck in different ways, so match the shank to the chuck.
  • Forcing a dull bit: a sharp, honed edge cuts cleanly, and the COMOWARE listing notes a hardened and honed cutting edge for sharpness.

Drill bit chart: the short version

  1. Read the chart row for the marking on the bit.
  2. Match the size to the hole the job needs.
  3. Match the bit to the material the listing names for that set.
  4. Check the shank fits the chuck.
  5. Let the split point settle before the cut begins.

FAQ: lasers and CNC

What do the numbers on a drill bit chart mean?

Number sizes are a sizing system alongside fractional and letter sizes, and the chart lines each number up with the diameter it stands for. Read the marking on the bit shank and find its row on the chart.

What sizes does the COMOWARE set cover?

The COMOWARE set covers 1/16 to 1/4 inch in 16 pieces, with a 1/4 inch hex shank and a size index in the holder.

What is a split point drill bit?

A split point tip helps reduce walking and gives precise hole placement. The DEWALT set lists a 135 degree split point, and the CRAFTSMAN set lists a split point for clean, burr-free holes.

What is the difference between the DEWALT and CRAFTSMAN sets?

The DEWALT set lists a 135 degree split point, a tapered web, a black and gold coating, and a 3-flats shank on sizes larger than 3/16 inch. The CRAFTSMAN set lists a gold oxide coating and a split point, in a carrying case. The CRAFTSMAN listing calls the case metal in the same bullet that calls it plastic, so the case material is not clear from the listing.

How do I know which drill bit size to use?

Start from the hole the job needs, find the marking on the chart that stands for that size, and read the marking on the bit shank before the bit goes in the chuck. The COMOWARE holder carries a size index for checking the size before the bit leaves the case.

Do these drill bits work on metal?

The DEWALT and CRAFTSMAN sets list plastic, wood and metal, and the COMOWARE set lists wood, plastic and aluminum alloy.

Related: the CNC tooling hub, best drill bit for stainless steel, collet vs drill chuck for CNC and drill bit sharpener for home use.

More buying guides

CNC Tooling ·

Drill Bit Types Chart and Uses Guide

A drill bit types chart groups fractional, letter, and numbered bits by size, so a maker can match the bit to the hole, the…