Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Router Bit Speed Chart by Material and Diameter

A router bit speed chart sets a safe speed by bit diameter, and this guide shows how to read it from the sizes the listings state.

Router Bit Speed Chart by Material and Diameter
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1SPEED TIGER INTA Carbide Roughing End MillSPEED TIGER INTA Carbide Roughing End Mill9.7/10View on Amazon
  2. 2HHIP 8000-0002 4 Flute High Speed Steel End Mill SetHHIP 8000-0002 4 Flute High Speed Steel End Mill Set9.5/10View on Amazon
  3. 31" 4 Flute End Mill1" 4 Flute End Mill9.5/10View on Amazon

A groove that burns dark at the edges, a roundover that chatters instead of cutting clean, an edge that tears where it should shine: the cause is often speed, not the bit. A router bit speed chart pairs bit diameter with a maximum safe speed, so the cut stays clean and the bit stays cool. This guide explains how to read a router bit speed chart, match the diameter to the cut, and find the speed a setup needs from the machine manual.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

The listings behind this guide state bit sizes, profiles and materials, but no RPM figures, so this guide gives no speed numbers of its own. Use the chart on the machine or in the machine manual for the speed, and use the sizes here to find the right row.

How to read the router bit speed chart

A router bit speed chart is read by diameter: find the row for the bit diameter and read the maximum speed for that size. The chart gives a maximum speed, not a fixed speed for every cut, and the cut itself shows whether the setting suits the job: a clean edge with light shavings means the setting works, while burning or chatter means the setting needs a change. The listings here cover diameters from 1/4 inch to 3/4 inch, with a 5/8 inch V-groove among the profiles, so the chart rows for those diameters are the ones that matter for the sets here.

Diameter sets the speed on the chart: a small-diameter bit runs faster than a large-diameter bit, and a large-diameter bit runs slower, since the cutting edge of a large bit travels farther with each turn. The material does not change the speed on the chart; it changes the feed and the depth of cut, so the listings here name wood, MDF, particle board, plywood and solid wood, and each material takes its own feed and depth of cut. When a chart gives a range rather than a set figure, start at the slow end of the range and move up only if the cut stays clean.

Match the bit diameter to the cut

The Skil 15-piece set lists straight bits in 1/4 inch, 1/2 inch and 3/4 inch, cove bits in 1/4 inch and 1/2 inch, dovetail bits in 3/8 inch and 1/2 inch, roundover bits in 1/4 inch, 1/2 inch and 3/8 inch, a 5/8 inch V-groove bit, a 45° chamfer bit, a 1/4 inch corebox bit, a 1/4 inch rabbeting bit and a 1/4 inch Roman ogee bit. The Skil 30-piece set is a larger carbide-tipped set with the same 1/4 inch shank fit, and the 100-piece set lists a 1/4 inch shank range for wood, MDF and plywood. Diameter decides the width of the cut: a 1/4 inch straight bit cuts a narrow groove, a 1/2 inch straight bit cuts a wider groove, and a 3/4 inch straight bit cuts the widest groove of the set.

Use a small diameter where the cut is fine detail or a light edge pass, and a large diameter where the cut is a wide groove or a broad edge profile. A large bit removes more material with each pass, so it needs a slower speed and a lighter pass than a small bit cutting the same material. The router speed vs bit diameter guide sets out the same link between size and speed, and the CNC router bit types guide covers the profiles by shape.

Match the profile to the material

Profiles shape the edge, and the listings here name the profiles woodworkers reach for most: straight bits for grooves, cove and roundover bits for softened edges, a chamfer bit for a bevel, a V-groove bit for detail lines, a dovetail bit for joints, a corebox bit for rounded grooves, a rabbeting bit for rebates and a Roman ogee bit for trim. The what is a compression router bit guide explains a profile that suits clean edges in sheet goods.

The listings name wood, MDF, particle board, plywood and solid wood as the materials for these bits, and each material cuts its own way: solid wood cuts cleanest along the grain, MDF and particle board cut the same in any direction, and plywood needs a light pass so the face stays clean. The bits here are for wood and wood sheet goods only: the listings warn against cutting ferrous metal and non-wood materials such as steel, iron and sand. The MDF vs plywood for CNC router guide compares the sheet goods side by side.

Shank size and fit

Each set here uses a 1/4 inch shank, and the listings state the fit plainly: the bits suit routers mounted to a router table or handheld routers that accept 1/4 inch shank router bits. Match the shank to the collet before ordering, because a bit only fits a collet of the same size, and a loose fit is a risk at speed. The router bit set vs individual router bits guide weighs a set against buying bits one at a time, and the best router bit for beginners guide picks sets for a first kit.

Common mistakes to avoid

  • Looking for a material column on the chart, which sets the speed by diameter, not by material.
  • Running a large-diameter bit at the speed meant for a small bit, which loads the bit and burns the edge.
  • Cutting metal or sand with a wood bit, against the warning in the listings.
  • Skipping the machine manual and guessing the speed instead of reading the chart on the machine.
  • Fitting a bit to a collet of the wrong size, or running a bit the router cannot hold.

Router bit speed chart: the short version

  1. Find the row for the bit diameter on the chart.
  2. Read the maximum speed for that diameter.
  3. Set the feed and the depth of cut for the material.
  4. Check the speed against the machine manual or the chart on the machine.
  5. Cut a trial piece and adjust only if the edge burns or chatters.

FAQ: lasers and CNC

What speed should a 1/2 inch router bit run at?

The speed comes from the chart row for a 1/2 inch bit, checked against the machine manual. The listings here give the diameter but no RPM figure, so read the machine chart for the speed and use the 1/2 inch row to find it.

Does a larger router bit need a slower speed?

Yes. A larger diameter means the cutting edge travels farther with each turn, so the chart sets a slower speed for larger bits and a faster speed for smaller bits. Diameter sets the speed; the material changes the feed and the depth of cut, not the speed.

Can a 1/4 inch shank bit fit any router?

No. A 1/4 inch shank bit fits routers that accept 1/4 inch shank bits, whether handheld or mounted to a router table. Check the collet size before ordering, because a bit only fits a collet of the same size.

Can router bits cut metal?

No, not the bits in the listings here. The listings name wood, MDF, particle board, plywood and solid wood, and warn against cutting ferrous metal and non-wood materials such as steel, iron and sand.

What is the difference between a 1/4 inch and a 1/2 inch straight bit?

Diameter and cut width. A 1/4 inch straight bit cuts a narrow groove and a 1/2 inch straight bit cuts a wider groove, and the chart sets a slower speed for the larger diameter. Each suits the same materials, so the choice comes down to the width of the cut.

Where do you find the speed for your router?

In the machine manual or on the chart on the machine. The listings here give sizes, profiles and materials but no RPM figures, so the machine chart is the source for the speed.

Related: the router speed vs bit diameter guide, the CNC router bit types guide and the best router bit for beginners guide. Also see the how to set up a spoilboard on a CNC guide.

More buying guides