Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Ptfe Teflon Tubing (2026)

Four PTFE tubes for Bowden 3D printers, from 1 meter to 25 ft, compared by inner diameter, length, heat rating and what each listing states about safety and warranty.

Best Ptfe Teflon Tubing (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ALLEN TECH 3mm PTFEBest OverallALLEN TECH 3mm PTFE9.6/10View on Amazon
  2. 2Creality Capricorn 2MBest for 1.75mm FilamentCreality Capricorn 2M9.5/10View on Amazon
  3. 3Quickun 4x6mm PTFEBest 6mm TubingQuickun 4x6mm PTFE9.5/10View on Amazon

The print head slides back and forth while the filament feeds through a tube that bends with every move. When that tube kinks, drags or fits loosely, prints fail and filament jams. The best ptfe teflon tubing for a Bowden printer is the size your printer takes, with a smooth bore and a heat rating that matches the hot end, and this guide compares the tubes on the figures each listing publishes.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Quick picks

  • Best Overall ALLEN TECH 3mm PTFE: 25 ft of tubing for 1.75mm filament with a UL flame rating and FDA food-contact requirements stated. Check price on Amazon
  • Best for 1.75mm Filament Creality Capricorn 2M: A 1.9mm bore made for 1.75mm filament, with a stated 0.04 friction coefficient and heat resistance up to 260 C. Check price on Amazon
  • Best 6mm Tubing Quickun 4x6mm PTFE: A 4mm ID by 6mm OD tube, 10 ft long, with a UL flame rating and flexible tracking for a moving print head. Check price on Amazon

Machines on the list

PTFE Teflon tubing 25ft

PTFE Teflon tubing 25ft

ALLEN TECH9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 25 ft PTFE tube with a 3mm inner diameter for 1.75mm filament, with a UL flame rating and FDA food-contact requirements stated.

Pros

  • 25 ft length, the longest tube here
  • 3mm ID by 4mm OD, listed for 1.75mm filament Bowden printers
  • UL-224 VW-1 flame rating stated
  • Raw materials meet FDA requirements per FDA 21 CFR 177.1550

Cons

  • No warranty term is stated
  • 3mm ID is a looser fit for 1.75mm filament than the Creality 1.9mm ID
  • No friction coefficient figure is stated
  • Length is fixed at 25 ft, with no shorter length listed
Quickun PTFE Teflon Tubing Tube

Quickun PTFE Teflon Tubing Tube

Quickun9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 10 ft PTFE tube, 4mm ID by 6mm OD, with a UL flame rating and flexible tracking for a moving print head.

Pros

  • 4mm ID by 6mm OD, the 6mm tube in this guide
  • 10 ft length, packaged without ties to prevent crimping
  • UL-224 VW-1 flame rating stated
  • Flexible tubing for tracking a moving print head, per the listing

Cons

  • No warranty term is stated
  • 4mm inner diameter is a loose fit for 1.75mm filament
  • Aqua is the only color listed
Creality Official Capricorn Bowden Tubing 2M

Creality Official Capricorn Bowden Tubing 2M

Creality9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2 m Capricorn Bowden tube with a 1.9mm inner diameter for 1.75mm filament and a 0.04 friction coefficient.

Pros

  • 1.9mm inner diameter made for 1.75mm filament
  • A 0.04 friction coefficient is stated
  • Heat resistant up to 260 C, per the listing
  • Three lengths are listed: 1 m, 2 m and 3 m

Cons

  • No warranty term is stated
  • No safety certification is stated
  • Outer diameter is not stated
  • Made for 1.75mm filament, so it does not fit larger filament sizes
Feelers PTFE Teflon Tubing

Feelers PTFE Teflon Tubing

Feelers9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A translucent 1 meter tube rated from minus 454 to 500 degrees Fahrenheit, with an FDA statement, a UL-224 VW-1 UL-224 VW-1 and an ASTM D543 solvent note.

Pros

  • Translucent finish
  • Rated from minus 454 to 500 degrees Fahrenheit
  • FDA requirements per FDA 21 CFR 177.1550 and a UL-224 VW-1 UL-224 VW-1
  • Density of 2.15 to 2.20 g/cm3 and ASTM D543 solvent resistance stated

Cons

  • No warranty term is stated
  • 1 meter gives the least length of the five tubes
  • No cutter or connectors in the box

Other machines to compare

Specs compared

Model HQ Score Inner diameter Outer diameter Length Heat rating Safety statement Warranty
ALLEN TECH 3mm PTFE 9.6/10 3 mm 4 mm 25 ft -454 to 500 F UL-224 VW-1, FDA 21 CFR 177.1550 Not stated
Quickun 4x6mm PTFE 9.5/10 4 mm 6 mm 10 ft -454 to 500 F UL-224 VW-1 Not stated
Creality Capricorn 2M 9.5/10 1.9 mm Not stated 2 m Up to 260 C Not stated Not stated
Feelers 2x4mm PTFE 9.5/10 2 mm 4 mm 1 m Not stated Not stated Not stated

Size and performance figures are the brand’s ratings quoted from listings on 11 November 2026. Inner diameter is the bore the filament runs through, and outer diameter is the tube size the Bowden fittings take.

What the listings tell you, and what they leave out

Four PTFE tubing listings were read for this guide. Two stated a UL flame rating, one stated FDA food-contact requirements, and none stated a warranty term. Only one listing stated a friction coefficient, and one listing gave no outer diameter at all.

Length is the least consistent figure: the listings give it in feet, meters and inches, so compare the numbers as listed and check the unit before you order.

Buying guide: choosing the best ptfe teflon tubing

Inner diameter and filament size

The inner diameter is the bore the filament runs through. For 1.75mm filament, the listings here give a 1.9mm bore on the Creality Capricorn, a 2mm bore on the Feelers tube and a 3mm bore on the ALLEN TECH tube. The Quickun tube has a 4mm bore, which is a loose fit for 1.75mm filament, so it fits general tube runs rather than a 1.75mm Bowden setup. Match the bore to your filament before you order, and check the outer diameter against your Bowden fittings: the ALLEN TECH and Feelers tubes are 4mm outside, and the Quickun tube is 6mm outside.

Length and flexibility

Lengths here run from 1 meter to 25 ft. The ALLEN TECH tube is the longest at 25 ft, the Quickun tube is 10 ft, the Creality tube is 2 m, and the Feelers tube is 1 meter. A longer tube covers a printer with the spool mounted far from the print head, while a short tube suits a single replacement run. Flexibility matters because the tube tracks the moving print head: the Quickun listing calls its tubing impressively flexible, and the Creality listing says its tube is more flexible than ordinary white Teflon tubes. The Quickun tube is packaged without ties to prevent crimping, so check the tube for kinks when it arrives.

Heat rating

Two tubes state a temperature range of -454 to 500 F: the ALLEN TECH and Quickun tubes. The Creality tube states heat resistance up to 260 C. The units differ, so compare the figures as listed and do not convert between them. The Creality listing also says its tube is not easy to carbonize under high temperature, compared with ordinary white Teflon tubes.

Friction and filament flow

A smooth bore keeps filament feeding without sticking. The Creality listing states a friction coefficient of 0.04 and says the precise inner diameter keeps filament flow even and smooth. The ALLEN TECH listing claims high lubricating ability and a non-stick surface, and the Quickun listing calls PTFE the smallest friction coefficient in plastics. Only the Creality listing gives a friction figure, so the other claims cannot be compared on numbers.

Project Match

Match the tube to the job:

  • Bowden setups running 1.75mm filament: Creality Capricorn 2M, ALLEN TECH 25 ft, Feelers 2x4mm PTFE.
  • A long tube run: ALLEN TECH 25 ft, the longest length here.
  • A 6mm outside diameter tube: Quickun 4x6mm PTFE.
  • Food-contact or chemical use: ALLEN TECH 25 ft, the only tube here with FDA food-contact requirements stated.
  • A short replacement length: Feelers 2x4mm PTFE, 1 meter.

How the scores add up

Each tube is scored out of 10 on performance, build, value, safety and warranty. A spec the listing does not publish scores nothing.

Product HQ Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
ALLEN TECH 3mm PTFE 9.6 29 21 21 8 0
Quickun 4x6mm PTFE 9.5 27 20 20 7 0
Creality Capricorn 2M 9.5 33 22 21 0 0

We translate weighted points into a score with 9.2 as its floor and 9.8 as its cap; the straight-line conversion keeps the ranking exactly.

FAQ: lasers and CNC

Where can I buy PTFE tubing for a 3D printer?

The four tubes in this guide are Amazon listings, and the size to check before you order is the inner diameter, the outer diameter and the length. Match the inner diameter to your filament and the outer diameter to your Bowden fittings.

How flexible is PTFE tubing?

The listings here describe PTFE tubing as flexible. The Quickun listing calls its tubing impressively flexible for tracking a moving print head, and the Creality listing says its tube is more flexible than ordinary white Teflon tubes. No stiffness figure is stated for any tube here.

How rigid is PTFE tubing?

It is flexible tubing, not rigid pipe. The listings describe bending and tracking a moving print head, and the Quickun listing notes its tube is packaged without ties to prevent crimping. No rigidity figure is stated.

What size PTFE tubing do I need for 1.75mm filament?

A tube with an inner diameter close to 1.75mm: the Creality Capricorn has a 1.9mm bore, the Feelers tube has a 2mm bore, and the ALLEN TECH tube has a 3mm bore, all listed for 1.75mm filament. Check the outer diameter too: the ALLEN TECH and Feelers tubes are 4mm outside, and the Quickun tube is 6mm outside.

How hot can PTFE tubing get?

The ALLEN TECH and Quickun listings state a temperature range of -454 to 500 F, and the Creality listing states heat resistance up to 260 C. Compare the figures as listed, since the units differ.

Related: the 3D printers hub and 3D printer accessories. Also see our best PTFE tubing 2mm ID, best 3D printing nozzle, 3D printer nozzle size, nozzle size comparison, best nozzle for Bambu Lab A1, best nozzle for Ender 3, best white PLA filament 1.75mm and best 3D printer lube and grease.

More buying guides

3D Printers ·

PTFE Tubing Sizes Chart for 3D Printers

PTFE tubing sizes for 1.75mm filament, with inner and outer diameters, lengths, fittings and temperature figures for four Bowden tubes.