PTFE Tubing Sizes Chart for 3D Printers
PTFE tubing sizes for 1.75mm filament, with inner and outer diameters, lengths, fittings and temperature figures for four Bowden tubes.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
PTFE Teflon tubing 10ft9.6/10View on Amazon - 2
PTFE Tube for 1.75mm Filament PTFE Tube 2.5mm9.5/10View on Amazon - 3
Creality Official Teflon Tube 2M9.5/10View on Amazon - 4
Creality Capricorn 2 Meters XS Series PTFE Bowden9.5/10View on Amazon
PTFE tubing sizes for 1.75mm filament come down to two numbers: the inner diameter the filament runs through and the outer diameter that fits the fitting. Two tubes here use 2.5mm ID by 4mm OD: the 3DMkspaceu kit and the Creality tube. The Capricorn XS (on Amazon) runs tighter at 1.9mm ID for flexible filament, and the Allen Tech tube (on Amazon) runs roomier at 3mm ID by 4mm OD. Lengths run from 2M to 5M, and the Allen Tech tube is 10ft.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

PTFE Teflon tubing 10ft
A translucent PTFE tube, 3mm ID by 4mm OD, 10ft for 1.75mm filament, with a UL-224 VW-1 flame standard.
Pros
- 3mm ID gives the roomiest bore here for 1.75mm filament
- UL-224 VW-1 flame standard stated
- Raw materials meet FDA 21 CFR 177.1550 for food contact surfaces
- Temperature range of -454 to 500 degrees F stated
Cons
- Tubing only, no cutter or fittings in the box
- 3mm ID leaves more wiggle room than the 1.9mm bore
- No warranty term is stated
- 10ft length is shorter than the 5M kit

PTFE Tube for 1.75mm Filament PTFE Tube 2.5mm
A 5M PTFE tube kit, 2.5mm ID by 4mm OD for 1.75mm filament, with a cutter and 10 PC4-M10 fittings.
Pros
- 2.5mm ID by 4mm OD suits 1.75mm filament
- Cutter and 10 PC4-M10 fittings included in the kit
- Withstands temperatures up to 260 degrees C
- Low-friction surface for TPU, TPE and PLA filament
Cons
- Built for 1.75mm filament systems only
- 5M of tubing to store
- Fittings are PC4-M10 only
- Cutter is a separate piece to keep with the kit

Creality Official Teflon Tube 2M
An official Creality PTFE tube, 2.5mm ID by 4mm OD, 2M long for 1.75mm filament, rated to 260 degrees C.
Pros
- 2.5mm ID by 4mm OD suits 1.75mm filament
- Heat resistant to 260 degrees C
- Fits K1, K2, CFS and Ender 3 V3 series printers
- Suits PLA, PLA+, ABS, PETG and TPU filament
Cons
- 2M length is shorter than the 5M kit
- No cutter or fittings included
- No warranty term is stated
- White tube hides filament color more than translucent tubing

Creality Capricorn 2 Meters XS Series PTFE Bowden
A 2-meter Capricorn XS Bowden tube with a 1.9mm ID for 1.75mm filament, with a PTFE tube cutter included.
Pros
- 1.9mm ID reduces wiggle room and buckling
- Suits flexible filaments on long Bowden systems
- Low friction with high lubricity additives
- PTFE tube cutter included
Cons
- 2-meter length is shorter than the 5M kit
- No fittings are included in the box
- Tight bore suits 1.75mm filament only
- Blue tube hides filament color more than translucent tubing
PTFE tubing sizes for 1.75mm filament
| Tube | Inner diameter | Outer diameter | Length | Filament |
|---|---|---|---|---|
| 3DMkspaceu 5M Kit | 2.5mm | 4mm | 5M (16.4ft) | 1.75mm |
| Creality 2M Tube | 2.5mm | 4mm | 2M | 1.75mm |
| Capricorn XS 2M | 1.9mm ± 0.05mm | Not stated | 2 meters | 1.75mm |
| Allen Tech 3mm ID | 3mm (0.118 in) | 4mm (0.158 in) | 10ft | 1.75mm |
How to read PTFE tubing sizes
ID is the bore the filament runs through, and OD is the outside that meets the fitting. Every tube here is listed for 1.75mm filament, with bores from 1.9mm to 3mm. The 3DMkspaceu kit includes 10 PC4-M10 fittings and a cutter for clean, flat cuts.
The Capricorn XS uses its tight 1.9mm bore to reduce wiggle room and buckling, which lets it print flexible filaments even on the longest Bowden systems, per the maker. The Allen Tech tube goes the other way, with a 3mm bore that gives the filament more room. The 3DMkspaceu tube (on Amazon) lists TPU, TPE and PLA, and the Creality tube lists PLA, PLA+, ABS, PETG and TPU.
The 3DMkspaceu and Creality tubes withstand temperatures up to 260 degrees C. The Allen Tech tube states a range of -454 to 500 degrees F. The Capricorn XS states higher temperature resistance than the TL series without giving a figure.
The tubing
Once the ID and OD are set, these four tubes span the bores in this guide, from the 1.9mm Capricorn XS bore to the 3mm Allen Tech bore. Two include a cutter, and the 3DMkspaceu kit adds 10 PC4-M10 fittings.
FAQ: lasers and CNC
What size PTFE tubing fits 1.75mm filament?
Two of the four tubes here use 2.5mm ID by 4mm OD: the 3DMkspaceu kit and the Creality tube. The Capricorn XS uses a tighter 1.9mm ID, and the Allen Tech tube uses a roomier 3mm ID.
What do ID and OD mean on PTFE tubing?
ID is the inner diameter, the bore the filament runs through. OD is the outer diameter, the outside that meets the fitting. A 2.5mm ID by 4mm OD tube has a 2.5mm bore in a 4mm tube.
What temperature figures do these tubes state?
The 3DMkspaceu and Creality tubes state up to 260 degrees C, and the Allen Tech tube states -454 to 500 degrees F. The Capricorn XS gives no figure.
Do I need the fittings and cutter?
The 3DMkspaceu kit includes a cutter and 10 PC4-M10 fittings, and the Capricorn XS includes a PTFE tube cutter. The cutter gives clean, flat cuts that, per the maker, minimize misalignment and filament jams. The Creality and Allen Tech tubes come without a cutter or fittings.
Can I print flexible filament through these tubes?
The Capricorn XS is built for it: its 1.9mm bore reduces wiggle room and buckling, and it prints flexible filaments on long Bowden runs, per the maker. The 3DMkspaceu tube lists TPU and TPE, and the Creality tube lists TPU.
Related: the 3D printer hub, best FDM 3D printing filament and problems with 3D printing. Also see best 3D printer nozzle cleaning kit. Also see Overture PLA vs Polymaker PLA.




