Best Matte Finish Petg Filament (2026): 5 Picks Compared
5 matte PETG filaments compared by print speed, spool size, matte finish and warranty, from a 0.5 kg carbon fiber spool to a 4.4 kg 4-pack.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallSUNLU High Speed PETG9.7/10View on Amazon - 2
Best Large BundleJAYO Matte PETG 4-Pack9.7/10View on Amazon - 3
Best for PrecisionIEMAI Matte PETG9.6/10View on Amazon - 4
Best Flexural StrengtheSUN PETG Matte9.6/10View on Amazon - 5
Best Carbon FiberFiberon PETG-rCF089.6/10View on Amazon
A matte PETG print hides layer lines and looks less like plastic, which is why makers reach for it for cosplay props, functional parts and pieces they plan to sell. This guide compares the best matte finish petg filament picks by what each listing states: print speed, spool size, matte finish and warranty.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall SUNLU High Speed PETG: A 2 kg 2-pack with a 30 to 600 mm/s print range, a soft matte finish and a stated 1 year warranty. Check price on Amazon
- Best Large Bundle JAYO Matte PETG 4-Pack: A 4.4 kg 4-pack with reusable spools, 30 to 600 mm/s printing and heat resistance up to 70°C. Check price on Amazon
- Best for Precision IEMAI Matte PETG: A 1 kg spool with ±0.02 mm accuracy, strong bed adhesion and a stated 30-day warranty. Check price on Amazon
- Best Flexural Strength eSUN PETG Matte: A 1 kg spool in light khaki with 77.1 MPa flexural strength and chemical and UV resistance. Check price on Amazon
- Best Carbon Fiber Fiberon PETG-rCF08: A 0.5 kg spool with 8 wt% recycled carbon fiber, a matte finish and low warping for functional parts. Check price on Amazon
Machines on the list

SUNLU High Speed PETG Filament 1.75mm, Black
A 2 kg 2-pack of high speed PETG in black, with a 30 to 600 mm/s print range, a soft matte finish and a stated 1 year manufacturer warranty.
Pros
- 30 to 600 mm/s print range with a settings table by speed
- 2 kg total across 2 spools in black
- Soft, even matte finish that reduces the glossy sheen
- 1 year manufacturer warranty stated in the listing
Cons
- No drying guidance in the listing
- Only black is listed in this bundle
- No flexural strength figure in the listing
- No heat distortion temperature in the listing

JAYO High Speed Matte PETG 1.75mm Filament Bundle
A 4.4 kg 4-pack of high speed matte PETG in black, with reusable spools, a 30 to 600 mm/s print range and heat resistance up to 70°C.
Pros
- 30 to 600 mm/s print range for rapid prototyping
- 4.4 kg total across 4 spools with reusable spools
- Smooth, non-reflective matte surface that conceals layer lines
- Vacuum-sealed spools with desiccant
Cons
- No warranty term in the listing
- The 40% print time reduction is the maker's claim against standard PETG
- No nozzle or bed temperature in the listing
- No flexural strength figure in the listing

IEMAI Matte PETG Filament 1.75mm
A 1 kg spool of matte PETG in black, with ±0.02 mm accuracy, strong bed adhesion and a stated 30-day warranty.
Pros
- ±0.02 mm dimensional accuracy
- Strong bed and interlayer adhesion to reduce warping
- Matte, low-gloss surface with reduced visible layer lines
- 30-day warranty with free returns or exchanges stated
Cons
- Print speed is limited to 150 mm/s or below
- Drying takes 5 to 8 hours at 60°C before printing
- No flexural strength figure in the listing
- No heat distortion temperature in the listing

eSUN PETG Matte Filament 1.75mm
A 1 kg spool of matte PETG in light khaki, with 77.1 MPa flexural strength, chemical and UV resistance and a smooth matte surface.
Pros
- 77.1 MPa flexural strength stated in the listing
- Heat distortion temperature 20°C above Matte PLA and 7°C above standard PETG
- Smooth matte surface with minimal shrinkage and warping
- Compatible with Bambu Lab, Voron, Raise3D, Prusa and Creality printers
Cons
- No warranty term in the listing
- No print speed in the listing
- No nozzle or bed temperature in the listing
- The flexural strength comparison is the maker's claim against Matte PLA

Polymaker Fiberon PETG-rCF08 Recycled CF Filament
A 0.5 kg spool of recycled carbon fiber PETG in black, with 8 wt% recycled carbon fiber, a matte finish and low warping for functional parts.
Pros
- 8 wt% recycled carbon fiber for rigidity and strength
- Matte surface that helps reduce the visibility of layer lines
- Low warping without a heated chamber
- HDT of 68.6°C at 0.45 MPa stated
Cons
- A hardened or wear-resistant nozzle is required because carbon fiber is abrasive
- Speeds up to 300 mm/s may be achieved after calibration
- No warranty term in the listing
- Intended for functional parts used at moderate temperatures
Other machines to compare
SUNLU High Speed PETG 3D Printer Filament 1.75mmCheck price on Amazon
SUNLU High Speed PETG Filament 1.75mmCheck price on Amazon
SUNLU High Speed PETG Filament 1.75mm 4KGCheck price on Amazon
Creality PETG Filament 1.75mmCheck price on Amazon
JAYO Black High Speed Matte PETG Filament 1.75mm 1.1kgCheck price on Amazon
Specs compared
| Model | HQ Score | Print speed | Spool | Matte finish | Warranty |
|---|---|---|---|---|---|
| SUNLU High Speed PETG | 9.7/10 | 30 to 600 mm/s | 2 kg, 2-pack | Soft, even matte effect | 1 year manufacturer |
| JAYO Matte PETG 4-Pack | 9.7/10 | 30 to 600 mm/s | 4.4 kg, 4-pack | Smooth, non-reflective | Not stated |
| IEMAI Matte PETG | 9.6/10 | Up to 150 mm/s | 1 kg | Smooth, low-gloss | 30-day warranty |
| eSUN PETG Matte | 9.6/10 | Not stated | 1 kg | Smooth, matte surface | Not stated |
| Fiberon PETG-rCF08 | 9.6/10 | Up to 300 mm/s | 0.5 kg | Carbon fiber texture | Not stated |
Specifications are manufacturer stated, as published on each listing and collected 11 November 2026. Speed is the print speed each listing states.
What the listings tell you, and what they leave out
We read 5 matte PETG listings for this guide. Only 2 stated a warranty term, and only 1 stated a flexural strength figure. 2 list a 30 to 600 mm/s print range, and 1 needs a hardened nozzle. Only 2 of the 5 listings state drying guidance. Polymaker is the only listing that states a heat distortion temperature as a figure, at 68.6°C at 0.45 MPa.
Treat the speed figures as the listing’s rated range, not a measured result: Polymaker says speeds up to 300 mm/s may be achieved after calibration, and JAYO says its filament reduces print time by up to 40% compared to standard PETG. SUNLU pairs each speed band with a nozzle temperature, so match the temperature to the speed you print at.
Buying guide: choosing the best matte finish petg filament
Print speed
SUNLU and JAYO list a 30 to 600 mm/s print range. Polymaker lists speeds up to 300 mm/s that may be achieved after calibration, and IEMAI lists a printing speed of 150 mm/s or below. eSUN lists no print speed. SUNLU pairs each speed band with a nozzle temperature: 230 to 240°C at 50 to 100 mm/s, 240 to 255°C at 100 to 300 mm/s, and 255 to 270°C at 300 to 600 mm/s. Match the nozzle temperature to the speed band you print in.
Spool size and bundles
Spool sizes run from 0.5 kg to 4.4 kg: Polymaker sells a 0.5 kg spool, eSUN and IEMAI sell 1 kg spools, SUNLU sells a 2 kg total 2-pack, and JAYO sells a 4.4 kg 4-pack. JAYO uses reusable spools, and each spool is vacuum-packed with desiccant. A larger bundle suits a maker who prints often, while a 1 kg spool suits a maker who wants to try a color or a brand.
Matte finish and layer lines
Every listing here promises a matte finish, but each describes it differently. SUNLU calls it a soft, even matte effect that reduces the glossy sheen of traditional plastics. JAYO calls it a smooth, non-reflective surface that conceals layer lines. Polymaker says the carbon fiber texture creates a matte finish that helps reduce the visibility of layer lines. eSUN promises a smooth, matte surface with no obvious layer lines, and IEMAI promises a smooth, low-gloss surface with reduced visible layer lines.
Heat and strength
eSUN states 77.1 MPa flexural strength and says its heat distortion temperature is 20°C higher than Matte PLA and 7°C better than standard PETG. Polymaker states a heat distortion temperature of 68.6°C at 0.45 MPa for functional parts used at moderate temperatures. JAYO states heat resistance up to 70°C. SUNLU states enhanced toughness and high impact strength, and IEMAI states higher impact and heat resistance than PLA without a figure. Match the heat and strength figures to the part: a functional part that carries a load needs the stated figures, not the matte finish.
Drying and storage
Polymaker says to dry the filament at 65°C for 3 hours if it has absorbed moisture, and to store it in a sealed, dry environment. IEMAI says to dry matte PETG at 60°C for 5 to 8 hours before printing. JAYO vacuum-seals each spool with desiccant. SUNLU and eSUN state no drying guidance. Dry filament before a long print, and store open spools sealed and dry.
Polymaker lists drying at 65°C for 3 hours and IEMAI lists drying at 60°C for 5 to 8 hours. JAYO ships each spool vacuum-sealed with desiccant. If a spool has absorbed moisture, dry it before printing and store it sealed and dry.
Project Match
- Cosplay props and decorative models: IEMAI and eSUN, both of which list cosplay props among their uses.
- Functional parts, brackets, jigs and fixtures: Polymaker, which lists prototypes, brackets, housings, jigs and fixtures, and JAYO, which lists functional parts and mechanical components.
- Outdoor models and decorations: eSUN, which lists outdoor decorations and outdoor use, and JAYO, which lists outdoor-use models.
- Rapid prototyping at high speed: SUNLU and JAYO, which list a 30 to 600 mm/s print range.
- Prototypes with a clean, refined appearance: Polymaker, which lists clean-looking prototypes and a professional matte finish.
How the scores add up
Each filament is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. A spec the listing does not publish scores nothing.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| SUNLU High Speed PETG | 9.7 | 32 | 21 | 21 | n/a | 3 |
| JAYO Matte PETG 4-Pack | 9.7 | 32 | 21 | 22 | n/a | 0 |
| IEMAI Matte PETG | 9.6 | 29 | 21 | 20 | n/a | 1 |
| eSUN PETG Matte | 9.6 | 30 | 21 | 21 | n/a | 0 |
| Fiberon PETG-rCF08 | 9.6 | 30 | 22 | 18 | n/a | 0 |
We translate weighted points into a score with 9.2 as its floor and 9.8 as its cap; the straight-line conversion keeps the ranking exactly. An unpowered accessory whose listing names no safety feature is scored without safety, out of 90.
FAQ: lasers and CNC
What is matte PETG filament?
Matte PETG is PETG filament that prints with a low-gloss, non-reflective surface. All 5 listings in this guide state a matte finish, and each ties it to less visible layer lines or a less plastic-like appearance. SUNLU calls its finish a soft, even matte effect, and eSUN calls its finish a smooth, matte surface.
What print speed can matte PETG reach?
SUNLU and JAYO list a 30 to 600 mm/s print range. Polymaker lists speeds up to 300 mm/s that may be achieved after calibration. IEMAI lists a printing speed of 150 mm/s or below. eSUN lists no print speed. Match the nozzle temperature to the speed band: SUNLU lists 230 to 240°C at 50 to 100 mm/s, 240 to 255°C at 100 to 300 mm/s, and 255 to 270°C at 300 to 600 mm/s.
Do I need a hardened nozzle for carbon fiber PETG?
Yes, for the Polymaker Fiberon PETG-rCF08: the listing says a hardened or wear-resistant nozzle is required because carbon fiber is abrasive. The other 4 listings state no nozzle requirement. The Polymaker listing also says to use a 240 to 270°C nozzle, a 60 to 70°C build plate and 0 to 50% cooling fan.
How do I dry matte PETG filament?
Polymaker says to dry the filament at 65°C for 3 hours if it has absorbed moisture, and IEMAI says to dry matte PETG at 60°C for 5 to 8 hours before printing. Both say to store the filament sealed and dry. JAYO ships each spool vacuum-sealed with desiccant. SUNLU and eSUN state no drying guidance.
Which matte PETG filament has a warranty?
SUNLU states a 1 year manufacturer warranty, and IEMAI states a 30-day warranty with free returns or exchanges for product quality issues or defects. Polymaker, eSUN and JAYO state no warranty term in their listings.
Related: the 3D printer hub, filament types compared, how to dry filament, build plates for PETG, ABS filament for 3D printing and PLA filament.




