Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Kapton Tape for 3d Printer (2026)

Five polyimide tapes for 3D printer beds, compared by stated width, length, heat resistance and adhesive.

Best Kapton Tape for 3d Printer (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1MYJOR 2in 108ft TapeBest OverallMYJOR 2in 108ft Tape9.7/10View on Amazon
  2. 2Tapes Master 5-RollBest Value 5-RollTapes Master 5-Roll9.6/10View on Amazon
  3. 3DAOKAI 30mm TapeWidest Single RollDAOKAI 30mm Tape9.5/10View on Amazon

A print that lifts off the bed mid-print wastes filament and an evening, and a solder joint that bridges ruins a board. The best kapton tape for 3d printer beds holds the first layer down through heat, and the same polyimide tape masks boards for soldering. This guide compares five polyimide tapes by what each listing states: width, length, heat resistance and adhesive.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Quick picks

  • Best Overall MYJOR 2in 108ft Tape: 2 inches wide and 108 feet long, rated to 500°F continuous and 536°F short term, made for 3D printer beds. Check price on Amazon
  • Best Value 5-Roll Tapes Master 5-Roll: Five rolls of 3/8 inch, 1 mil polyimide tape with silicone adhesive and no residue. Check price on Amazon
  • Widest Single Roll DAOKAI 30mm Tape: 30mm wide and 90 feet long, rated to 280°C with silicone adhesive for 3D printing and masking. Check price on Amazon

Machines on the list

MYJOR High Heat Tape 2 Inch x 108 Ft

MYJOR High Heat Tape 2 Inch x 108 Ft

MYJOR9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2 inch by 108 foot polyimide roll rated to 500°F continuous and 536°F short term, listed for 3D printer beds, PCB masking and CPU protection.

Pros

  • Rated 500°F continuous, 536°F short term
  • Listed for 3D printer beds, ABS, PLA and Nylon
  • No residue stated after peeling
  • Hand-tearable, no scissors needed

Cons

  • No warranty stated
  • No adhesive type stated
  • A Kapton alternative, not branded Kapton
  • No thickness stated
Tapes Master 5 Rolls - 3/8" x 36 Yds 1 Mil

Tapes Master 5 Rolls - 3/8" x 36 Yds 1 Mil

Tapes Master9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Five rolls of 3/8 inch, 1 mil polyimide tape with silicone adhesive, listed as an alternative to 3M Kapton tape 5413 for 3D printer beds and soldering.

Pros

  • Five rolls in one listing
  • 1 mil polyimide with silicone adhesive
  • RoHS approved and halogen free
  • Listed for 3D printer bed surfaces

Cons

  • No warranty stated
  • No temperature figure stated
  • Narrow 3/8 inch width only
  • Flame retardant claim with no figure stated
MYJOR Kapton Tape 5 Rolls Pack

MYJOR Kapton Tape 5 Rolls Pack

MYJOR9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-roll polyimide kit in widths from 1/8 in to 5/8 in, each 108 ft, with silicone adhesive, stated for 500°F continuous use.

Pros

  • 5 widths from 1/8 in to 5/8 in, each 108 ft long
  • Silicone adhesive rated for 500°F continuous and 536°F peaks
  • Peels off cleanly with no residue, per the listing
  • Stated uses include PCB soldering, printer beds and battery packs

Cons

  • No warranty term is stated
  • No thickness is stated
  • Narrowest width is 1/8 in, so wide masking needs overlapping runs
  • 5 rolls to store, not a single roll
DAOKAI 30mm x 28m(90ft) High Temperature Tape High

DAOKAI 30mm x 28m(90ft) High Temperature Tape High

DAOKAI9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 30mm by 28m polyimide roll rated to 280°C, with silicone adhesive and no residue, listed for masking, soldering and 3D printing.

Pros

  • Rated 280°C (536°F)
  • 30mm wide, 28m long
  • Silicone adhesive, no residue stated
  • Listed for masking, soldering and 3D printing

Cons

  • No warranty stated
  • Spec table size reads only Large
  • No thickness stated
VCHOMY 2Rolls 10mmx33m(108ft)

VCHOMY 2Rolls 10mmx33m(108ft)

VCHOMY9.4/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

2 rolls of 10mm x 33m polyimide tape with silicone adhesive, heat resistant up to 500°F for half an hour, for heat press, sublimation and PCB soldering.

Pros

  • 2 rolls of 10mm x 33m tape per pack
  • Heat resistant up to 500°F for half an hour
  • Silicone adhesive; easy to cut with no residue
  • Dark brown while not torn; clear yellow while peeled off

Cons

  • No warranty term is stated in the listing
  • No film thickness is stated in the listing
  • Only 10mm width; no wider roll is listed
  • No adhesive thickness is stated in the listing

Other machines to compare

Specs compared

Model HQ Score Width Length Heat resistance Adhesive Rolls
MYJOR 2in 108ft Tape 9.7/10 2 in 108 ft 500°F continuous, 536°F short term Not stated 1
Tapes Master 5-Roll 9.6/10 3/8 in 36 yds Not stated Silicone 5
DAOKAI 30mm Tape 9.5/10 30mm (1.18 in) 28m (90 ft) 280°C (536°F) Silicone 1
MYJOR 5-Roll Pack 9.6/10 1/8 to 5/8 in Not stated 536°F Not stated 5
VCHOMY 2-Roll Tape 9.4/10 10mm 33m (108 ft) 500°F Silicone 2

Size and performance figures are the brand’s ratings quoted from listings on 11 November 2026. Width is the tape width; length is the roll length as listed.

What the listings tell you, and what they leave out

Five polyimide tape listings were read. Three give full bullets and spec tables, and two give a title only. Only one states a continuous temperature and a short-term temperature, and only one states a thickness. Three state silicone adhesive, and none states a warranty term.

Buying guide: the best kapton tape for 3d printer

Width

Width decides how much bed or board one strip covers. The listings here offer 2 in, 3/8 in, 30mm, five widths from 1/8 to 5/8 in, and 10mm. A wider roll covers a bed in fewer strips, while a narrow roll suits masking small boards and tight areas.

Length and rolls

Roll length decides how many beds or boards one roll covers. The listings here offer 108 ft on a single roll, 36 yds on each of five rolls, 28m on one roll, and 33m on each of two rolls. A multi-roll pack suits a shop that masks boards often; a single long roll suits a printer that tapes the bed each time.

Heat resistance

Heat resistance is the number that matters most here, and only three listings state a figure. MYJOR’s 2 inch roll states 500°F continuous and 536°F short term. DAOKAI’s roll states 280°C. VCHOMY’s rolls state 500°F. The Tapes Master pack states high temperature resistance with no figure, so its limit is not stated.

Adhesive

Three listings state silicone adhesive: the Tapes Master rolls, DAOKAI’s roll and the VCHOMY rolls. MYJOR’s 2 inch roll states strong adhesion with no residue but names no adhesive type. Three listings state no residue after peeling: MYJOR’s 2 inch roll, the Tapes Master rolls and DAOKAI’s roll.

Kapton vs polyimide

Kapton is a brand name for polyimide film. Two listings here describe themselves as Kapton alternatives: MYJOR’s 2 inch roll and the Tapes Master 5-roll pack. The others use Kapton in the title while describing polyimide film. Check the listing for the film and adhesive it actually states, not the brand word in the title.

For the bed itself, see our best smooth build plate for 3d printer.

Project Match

Project Pick Why it fits
3D printer bed MYJOR 2in 108ft Tape Listed for 3D printer beds, ABS, PLA and Nylon
3D printer bed, narrow strips Tapes Master 5-Roll Listed as a bed surface for 3D printers; 3/8 in rolls
PCB soldering mask MYJOR 2in 108ft Tape Listed for PCB soldering mask and gold fingers
Masking and soldering DAOKAI 30mm Tape Listed for masking, soldering and circuit boards
PCB soldering and 3D printer bed, assorted widths MYJOR 5-Roll Pack Title lists PCB soldering and 3D printer bed; five widths
Sublimation and heat press VCHOMY 2-Roll Tape Listed for sublimation, heat press and heat transfer

How the scores add up

Each tape is scored out of 10 on performance, build, value, safety and warranty, with the weights published on our How We Pick page. No listing here states a safety certification, so no safety points were scored. Performance covers stated heat resistance and 3D printer bed use; build covers how complete the spec table is; value covers roll length and roll count against the stated contents.

Product HQ Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
MYJOR 2in 108ft Tape 9.7 32 21 21 n/a 0
Tapes Master 5-Roll 9.6 29 21 22 n/a 0
DAOKAI 30mm Tape 9.5 28 19 20 n/a 0

We translate weighted points into a score with 9.2 as its floor and 9.8 as its cap; the straight-line conversion keeps the ranking exactly. An unpowered accessory whose listing names no safety feature is scored without safety, out of 90.

FAQ: lasers and CNC

Does kapton tape transfer heat?

The listings do not state a heat transfer figure. MYJOR’s roll states heat resistance to 500°F continuous and 536°F short term, and DAOKAI’s states 280°C, but neither lists a transfer rate. Pick by the stated resistance, not by a transfer claim.

What width of kapton tape do I need for a 3D printer bed?

It depends on the bed. The listings here offer 2 in, 3/8 in, 30mm, five widths from 1/8 to 5/8 in, and 10mm. A wider roll covers a bed in fewer strips; a narrow roll suits masking small boards.

Is kapton tape the same as polyimide tape?

Kapton is a brand name for polyimide film. Two listings here call themselves Kapton alternatives, and the others use Kapton in the title while describing polyimide film. Check the listing for the film and adhesive it actually states.

Does kapton tape leave residue?

Three listings here state no residue after peeling: MYJOR’s 2 inch roll, the Tapes Master rolls and DAOKAI’s roll. The other two state no residue claim, so check the listing before ordering.

Can I use kapton tape for soldering?

Yes, as a mask. MYJOR’s roll is listed as a PCB soldering mask, the Tapes Master rolls are listed for wave solder and solder dip protection, and DAOKAI’s roll is listed for soldering and masking circuit boards. The VCHOMY rolls name sublimation and heat press, not soldering.

Related: the 3d printers hub, the best kapton tape rolls and the best smooth build plate for 3d printer. Also see our best thick kapton tape. Also see our best small kapton tape. Also see our best glue stick for 3d printer build plate. Also see our flexible build plate vs pei sheet. Also see our best 3d printing cleaning kit.

More buying guides

3D Printers ·

Kapton Tape Price: What to Expect

Kapton tape price follows width, length, roll count and heat limits, so this guide explains what changes the amount and which rolls fit printing,…

3D Printers ·

Kapton Tape Temperature Rating Explained

MYJOR states 500F continuous and 536F in short peaks, the highest figures here, so match the stated figure to your soldering, printing or masking…