Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Kapton Tape Temperature Rating Explained

MYJOR states 500F continuous and 536F in short peaks, the highest figures here, so match the stated figure to your soldering, printing or masking job.

Kapton Tape Temperature Rating Explained
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1MYJOR Kapton Tape 1.2 Inch x 108 FtMYJOR Kapton Tape 1.2 Inch x 108 Ft9.5/10View on Amazon
  2. 2BOMEI PACK Polyimide TapeBOMEI PACK Polyimide Tape9.5/10View on Amazon
  3. 3APT, 1 mil Thick Polyimide Adhesive TapeAPT, 1 mil Thick Polyimide Adhesive Tape9.4/10View on Amazon
  4. 41''×33M High Temperature Resistant Polyimide1''×33M High Temperature Resistant Polyimide9.3/10View on Amazon

You are about to mask a board for soldering or hold a print to a heated bed, and the kapton tape temperature rating decides whether the tape holds or lifts. The rolls here are polyimide film with a silicone adhesive, made for hot work.

MYJOR states the highest figures here, 500F (260C) continuous and 536F (280C) in short peaks, and BOMEI PACK states 260C (500F) for half an hour. APT states 400F (260C), and DGXINHONG states no figure at all.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

MYJOR Kapton Tape 1.2 Inch x 108 Ft

MYJOR Kapton Tape 1.2 Inch x 108 Ft

MYJOR9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1.2 inch by 108 ft polyimide tape that states continuous heat of 500F (260C) and short peaks to 536F (280C), with a silicone adhesive that leaves no residue.

Pros

  • Continuous heat of 500F (260C), short peaks to 536F (280C)
  • Silicone adhesive removes cleanly with no residue after heat work
  • Amber color lets you see the parts underneath while masking
  • Names PCB soldering mask, 3D printer beds and CPU protection

Cons

  • No warranty term is stated
  • 1.2 inch width covers less per pass than the 2 inch BOMEI PACK
  • One roll per order, while BOMEI PACK gives two
  • 108 feet suits long runs more than a single small repair
BOMEI PACK Polyimide Tape

BOMEI PACK Polyimide Tape

BOMEI PACK9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2-pack of 2 inch by 108 ft polyimide tape, 2.36 mil thick, that states heat resistance up to 260C (500F) for half an hour, with a silicone adhesive that leaves no residue.

Pros

  • States heat resistance up to 260C (500F) for half an hour
  • 2.36 mil film, thicker than the 1 mil APT
  • Two rolls in the pack, each 2 inches wide and 108 feet long
  • Names H-class motor and transformer coil insulation, plus hot press and T-shirt work

Cons

  • Heat figure carries a half an hour limit, not continuous use
  • No warranty term is stated
  • 2 inch width is wide for fine masking
  • One width only: 2 inches, so fine masking needs a narrower roll
APT, 1 mil Thick Polyimide Adhesive Tape

APT, 1 mil Thick Polyimide Adhesive Tape

APT Advanced Polymer Tape9.4/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 mil polyimide tape, 1 inch by 36 yards, that states heat resistance as high as 400F (260C), with a silicone adhesive that removes cleanly and leaves no residue.

Pros

  • Silicone adhesive resists curling, shrinking and lifted edges
  • Removes cleanly with no residue after heat work
  • States RoHS and REACH compliance and the ASTM D-5213 standard
  • Names soldering, circuit boards, fiber optics cable, coils and 3D printing

Cons

  • 1 inch width covers less per pass than the 2 inch BOMEI PACK
  • Suits electronics and masking, not wide-area coverage
  • 1 mil film suits light masking more than heavy wrapping
  • One roll per order, while BOMEI PACK gives two
1''×33M High Temperature Resistant Polyimide

1''×33M High Temperature Resistant Polyimide

DGXINHONG9.3/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 inch by 33 m polyimide tape in widths from 1/8 inch to 2 inches, with a silicone adhesive that removes cleanly, but no stated temperature figure.

Pros

  • Widths from 1/8 inch to 2 inches for precision and large-area work
  • Silicone adhesive holds during use and removes cleanly with no residue
  • Names sublimation transfer, powder coating, masking and circuit boards
  • States the D-5213 standard

Cons

  • No stated temperature figure, the number this guide is about
  • The listed roll is 1 inch wide; wider work needs the 2 inch width
  • Names transfer and masking work, not coil insulation
  • A 33 m roll suits repeat jobs more than a single small repair

Kapton tape temperature rating: what the numbers mean

Read a temperature figure with its duration. MYJOR states both, continuous heat of 500F (260C) and short peaks to 536F (280C). BOMEI PACK states 260C (500F) for half an hour, so its figure carries a time limit. APT states 400F (260C) in one line, and those two figures do not match. DGXINHONG states no temperature figure at all.

Celsius and Fahrenheit figures sit side by side on the rolls that state them: 260C is 500F, and 280C is 536F. When the two figures on one roll do not agree, use the lower figure for your job.

Widths, thickness and length

Width decides what the tape covers in one pass. MYJOR comes 1.2 inches wide and 108 feet long, APT comes 1 inch wide and 36 yards long, and BOMEI PACK comes 2 inches wide and 108 feet long. DGXINHONG lists widths from 1/8 inch to 2 inches on a 33 m roll.

Thickness is stated in mils. APT states 1 mil, and BOMEI PACK states 2.36 mil. MYJOR and DGXINHONG state no thickness.

Where makers use it

Each roll names different jobs. MYJOR names PCB soldering mask, 3D printer beds and CPU protection. BOMEI PACK names H-class motor and transformer coil insulation, capacitor and wire wrapping, hot press and T-shirt work. APT names soldering, circuit boards, fiber optics cable, coils and 3D printing. DGXINHONG names sublimation transfer, powder coating, masking and circuit boards.

All four rolls use a silicone adhesive and leave no residue after peeling. MYJOR adds UV resistance and an amber color for seeing the parts underneath, and APT resists curling, shrinking and lifted edges.

Kapton tape for the job

The rolls below differ in stated temperature figure, width and length, so pick the one that matches your job.

FAQ: lasers and CNC

What temperature can Kapton tape handle?

It depends on the roll. MYJOR states 500F (260C) continuous and 536F (280C) in short peaks. BOMEI PACK states 260C (500F) for half an hour, APT states 400F (260C), though those two figures do not match, and DGXINHONG states no figure.

What is the difference between continuous and short-term heat on Kapton tape?

Continuous heat is the figure the tape holds without a break, and short-term heat is a peak it takes for a short time. MYJOR states 500F (260C) continuous and 536F (280C) as a short peak.

Which Kapton tape width should I buy?

Match the width to the area you mask. DGXINHONG lists widths from 1/8 inch to 2 inches, MYJOR comes 1.2 inches wide, and BOMEI PACK comes 2 inches wide.

Does Kapton tape leave residue after heating?

All four rolls state no residue after peeling, each with a silicone adhesive that releases clean.

Can I use Kapton tape on a 3D printer bed?

Yes, the listings name it. MYJOR names 3D printer beds, and APT and DGXINHONG name 3D printing. For filament and bed setup, see our FDM 3D printing filament guide.

Related: the 3D printers hub, best FDM 3D printing filament and 3D printer maintenance kit.

More buying guides

3D Printer Accessories ·

Best Spray Paint for Hard Plastic (2026)

Four spray paints for hard plastic, from a plastic-specific trim restorer to a textured automotive topcoat, compared by coverage, dry time and finish.