Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Kapton Tape Uses: 3D Printing, Heat Press and More

Kapton tape holds prints on the printer bed, masks circuit boards for soldering, and keeps heat-press transfers in place while they press.

Kapton Tape Uses: 3D Printing, Heat Press and More
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1APT, 1 mil Thick Polyimide Adhesive TapeAPT, 1 mil Thick Polyimide Adhesive Tape9.7/10View on Amazon
  2. 2Mr. Pen Heat Tape - 10mm x 33m (108ft), 2 RollsMr. Pen Heat Tape - 10mm x 33m (108ft), 2 Rolls9.6/10View on Amazon
  3. 3MS WGO 12mm X 33m 108ft Heat Tape Heat ResistantMS WGO 12mm X 33m 108ft Heat Tape Heat Resistant9.5/10View on Amazon
  4. 4MS WGO High Temperature Tape Heat Tape HeatMS WGO High Temperature Tape Heat Tape Heat9.5/10View on Amazon

Kapton tape uses cover the hot, sticky jobs around a maker bench: holding a print to the printer bed, masking a circuit board while you solder, and keeping a heat-press transfer from shifting while it presses. The tape is a thin polyimide film with a silicone adhesive that stands up to heat and peels off clean, and different rolls cover the printer, the soldering iron and the press. The sections below match each job to the tape that fits it.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

APT, 1 mil Thick Polyimide Adhesive Tape

APT, 1 mil Thick Polyimide Adhesive Tape

APT Advanced Polymer Tape9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 mil polyimide tape, 2 in wide and 36 yd long, rated to 400F (260C) with silicone adhesive and clean removal.

Pros

  • 2 in wide and 36 yd long, the widest roll here
  • Rated to 400F (260C) with silicone adhesive
  • Clean removal with no residue
  • RoHS and REACH compliance and ASTM D-5213

Cons

  • One roll in the box; two other picks come as 2-roll packs
  • 2 in width is wide for narrow masking jobs
  • Amber color shows on light-colored work
  • 260C rating sits below the 12mm MS WGO tape at about 280C
Mr. Pen Heat Tape - 10mm x 33m (108ft), 2 Rolls

Mr. Pen Heat Tape - 10mm x 33m (108ft), 2 Rolls

Mr. Pen9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Two rolls of 10mm polyimide tape, 33m (108ft) each, rated to 260C short period and 220C long period, with silicone adhesive.

Pros

  • Two rolls of 10mm tape, 33m (108ft) each
  • Rated to 260C short period and 220C long period
  • Polyimide film with silicone adhesive, no residue
  • Suits heat press, 3D printing, PCB boards and electrical wires

Cons

  • 10mm width is narrow for wide masking jobs
  • 220C long-period rating is below the 12mm MS WGO tape at about 280C
  • Brown color shows on light-colored work
  • Each roll is 10mm wide, so a printer bed needs several strips side by side
MS WGO 12mm X 33m 108ft Heat Tape Heat Resistant

MS WGO 12mm X 33m 108ft Heat Tape Heat Resistant

MS WGO9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12mm polyimide tape, about 30m long, rated to about 280C, with high insulation and no residue.

Pros

  • Rated to about 280C, the highest heat rating here
  • 12mm width with about 30m length
  • High insulation, acid and alkali resistance
  • Suits wave soldering, transformers, motors and coils

Cons

  • One roll in the box; two other picks come as 2-roll packs
  • 12mm width is narrow for wide masking jobs
  • Tawny color shows on light-colored work
  • No warranty term is stated
MS WGO High Temperature Tape Heat Tape Heat

MS WGO High Temperature Tape Heat Tape Heat

MS WGO9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Two rolls of 10mm polyimide tape, 33m (108ft) each, rated to 260C short period and 220C long period, with no residue.

Pros

  • Two rolls of 10mm tape, 33m (108ft) each
  • Rated to 260C short period and 220C long period
  • Suits wave soldering, heat press vinyl and PCB work
  • No residue after peeling

Cons

  • 10mm width is narrow for wide masking jobs
  • 220C long-period rating is below the 12mm MS WGO tape at about 280C
  • Mainly tawny color shows on light-colored work
  • No warranty term is stated

Kapton tape uses in 3D printing

A strip of Kapton tape on the print bed holds the first layer while it prints, and the print lifts off the tape when it finishes; the tape itself peels off the bed without residue when you replace it. The APT tape suits 3D printing, and the Mr. Pen tape (on Amazon) suits 3D printers. Match the width to the bed: a 2 in roll covers more bed in fewer strips than a 10mm roll, and a narrow roll suits small parts. For the heat limits of each roll, see the Kapton tape temperature rating guide.

Kapton tape uses for soldering and electronics

Kapton tape masks the parts of a circuit board that must stay clear of solder, and it insulates coils, transformers and motors while they run hot. The APT tape covers masking, soldering and circuit boards, and both MS WGO tapes cover wave soldering, transformers, motors and coils. The 10mm MS WGO tape protects gold fingers on boards during wave soldering. For iron settings, see the soldering temperature guide.

Kapton tape uses for heat press and sublimation

Kapton tape holds a heat transfer vinyl design in place on a shirt or a hat while the press runs, and it stands up to the heat of sublimation work. The MS WGO 10mm tape (on Amazon) and the Mr. Pen tape both cover heat press and sublimation uses, and the APT tape covers high temperature sublimation powder coating. For press settings by material, see the temperature guide for heat press.

Which kapton tape to use for each job

The rolls below cover the jobs above, from a wide roll for printer beds to narrow rolls for boards and presses.

FAQ: lasers and CNC

What is Kapton tape used for?

Kapton tape holds prints on the printer bed, masks circuit boards for soldering, and keeps heat-press transfers in place. It is a polyimide film with a silicone adhesive that stands up to heat and peels off without residue.

What temperature can Kapton tape handle?

It depends on the roll. The APT tape is rated to 400F (260C), the Mr. Pen tape and the 10mm MS WGO tape to 260C short period and 220C long period, and the 12mm MS WGO tape to about 280C.

Does Kapton tape leave residue?

No residue is stated for all four rolls here. The APT tape removes cleanly, and the Mr. Pen tape peels clean without marks.

What width of Kapton tape should I buy?

Match the width to the job. The APT roll is 2 in wide for beds and wide masking, while the 10mm and 12mm rolls suit narrow boards and small transfers. The Mr. Pen tape and the 10mm MS WGO tape come as 2-roll packs.

Can Kapton tape go on a 3D printer bed?

Yes. The APT tape lists 3D printing among its uses, and the Mr. Pen tape lists 3D printers.

Related: the best Kapton tape rolls, the best Kapton tape for 3D printer and the Kapton tape temperature rating guide. Also see the 3D printers hub.

More buying guides

3D Printers ·

Kapton Tape Price: What to Expect

Kapton tape price follows width, length, roll count and heat limits, so this guide explains what changes the amount and which rolls fit printing,…

3D Printers ·

Kapton Tape Temperature Rating Explained

MYJOR states 500F continuous and 536F in short peaks, the highest figures here, so match the stated figure to your soldering, printing or masking…