Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Thick Kapton Tape (2026): 5 Picks Compared

Five polyimide Kapton tapes compared by thickness, width, length and heat resistance, for 3D printer beds, soldering and sublimation.

Best Thick Kapton Tape (2026): 5 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1BOMEI PACK PolyimideBest OverallBOMEI PACK Polyimide9.6/10View on Amazon
  2. 2CCHUIXI Kapton 2 inBest Wide RollCCHUIXI Kapton 2 in9.6/10View on Amazon
  3. 3CoYlBod Polyimide 1 inBest Two-RollCoYlBod Polyimide 1 in9.5/10View on Amazon
  4. 4TekLine Gold KaptonBest for MaskingTekLine Gold Kapton9.5/10View on Amazon

A heated bed needs a clean surface that holds the first layer, a solder joint needs masking that survives the iron, and a sublimation blank needs tape that peels away without a mark. A thick Kapton tape covers those jobs in one roll, and the width decides how much ground each pass covers. This guide compares the best thick kapton tape picks for makers who run 3D printers, solder boards and press sublimation blanks, by thickness, width, length and heat resistance.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Quick picks

  • Best Overall BOMEI PACK Polyimide: 2.36 mil thick, 2 in wide and 108 ft long, with silicone adhesive and heat resistance to 260 C (500 F). Check price on Amazon
  • Best Wide Roll CCHUIXI Kapton 2 in: 2 in wide and 36 yards long, heat resistant to 500 F, with no-residue silicone adhesive. Check price on Amazon
  • Best Two-Roll CoYlBod Polyimide 1 in: 2 rolls of 1 in tape, 33 m each, with silicone adhesive and heat resistance to 260 C. Check price on Amazon
  • Best for Masking TekLine Gold Kapton: 1 mil film with 1.5 mil silicone adhesive, clean removal with no residue and non-corrosive residues. Check price on Amazon

Machines on the list

BOMEI PACK Polyimide Tape

BOMEI PACK Polyimide Tape

BOMEI PACK9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2.36 mil polyimide tape, 2 in wide and 108 ft long, with silicone adhesive and heat resistance to 260 C (500 F) for half an hour.

Pros

  • 2.36 mil thick, the thickest single figure stated here
  • 2 in wide and 108 ft long, with silicone adhesive and no residue
  • Heat resistant to 260 C (500 F) for half an hour
  • High tensile strength, per the listing

Cons

  • No warranty term is stated
  • No weight is stated
  • No roll diameter is stated
CCHUIXI Kapton Tape 2 Inch x 36 Yards

CCHUIXI Kapton Tape 2 Inch x 36 Yards

CCHUIXI9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2 in polyimide tape, 36 yards long, with silicone adhesive, no residue and heat resistance to 500 F (260 C), for 3D printer beds and soldering.

Pros

  • 2 in wide and 36 yards (108 feet) long
  • Heat resistant to 500 F (260 C) without melting or degrading, per the listing
  • Silicone adhesive leaves no sticky residue on removal
  • Dielectric strength and chemical resistance, per the listing

Cons

  • No warranty term is stated
  • No thickness figure is stated
  • No roll diameter is stated
  • The aerospace claim in the listing has no detail behind it
CoYlBod Polyimide Film Adhesive Tape High

CoYlBod Polyimide Film Adhesive Tape High

CoYlBod9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Two rolls of 1 in polyimide tape, 33 m each, with silicone adhesive, no residue and heat resistance up to 260 C (500 F).

Pros

  • 2 rolls in the pack, each 1 in wide and 33 m long
  • Heat resistant up to 260 C (500 F)
  • Silicone adhesive releases easily and leaves no residue
  • Solvent resistant, and will not melt or fade under high heat, per the listing

Cons

  • No warranty term is stated
  • No thickness figure is stated
  • No weight is stated
  • No roll diameter is stated
TekLine Gold Kapton Tape Polyimide High Temp 3/4"

TekLine Gold Kapton Tape Polyimide High Temp 3/4"

CML Supply9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3/4 in polyimide tape, 36 yards long, with 1 mil film and 1.5 mil silicone adhesive, clean removal and non-corrosive residues.

Pros

  • 1 mil polyimide film with 1.5 mil silicone adhesive, both figures stated
  • Clean removal with no residue, per the listing
  • Residues are non-corrosive, per the listing
  • High temperature tape that will not burn or wrinkle, per the listing

Cons

  • No warranty term is stated
  • No heat temperature figure is stated
  • 3/4 in is the narrowest width here
  • No roll diameter is stated
MYJOR Kapton Tape 4 Rolls Pack

MYJOR Kapton Tape 4 Rolls Pack

MYJOR9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-roll pack in 1/4, 1/2, 3/4 and 1 in widths, each roll 108ft long, with silicone adhesive and heat resistance up to 500°F for PCB soldering, 3D printer beds and CPU protection.

Pros

  • 4 widths from 1/4 in to 1 in per pack
  • Each roll measures 108ft (33m) in length
  • Heat resistant up to 500°F long-term, 536°F short-term
  • Silicone adhesive with a clean peel and no residue

Cons

  • No warranty term is stated in the listing
  • No film thickness is stated, so thinness is not measured
  • No adhesive thickness is stated in the listing
  • No laser or engraving use is stated in the listing

Other machines to compare

Specs compared

Model HQ Score Width Length Thickness Heat resistance Adhesive Warranty
BOMEI PACK Polyimide 9.6/10 2 in 108 ft 2.36 mil 260 C (500 F) for half an hour Silicone Not stated
CCHUIXI Kapton 2 in 9.6/10 2 in 36 yds (108 ft) Not stated 500 F (260 C) Silicone Not stated
CoYlBod Polyimide 1 in 9.5/10 1 in 33 m Not stated 260 C (500 F) Silicone Not stated
TekLine Gold Kapton 9.5/10 3/4 in 36 yds 1 mil film, 1.5 mil adhesive Not stated Silicone Not stated
MYJOR 4-Roll Pack 9.5/10 1/4, 1/2, 3/4, 1 in Not stated Not stated 500 F Not stated Not stated

Size and performance figures are the brand’s ratings quoted from listings on 11 November 2026. Where a listing states no figure, the table says so.

What the listings tell you, and what they leave out

5 listings were compared. Only 2 state a thickness figure, and only 1 of those states film and adhesive separately. Only 2 state a weight, and none states a warranty term. The MYJOR listing is title only, with no bullets or spec table.

Buying guide: choosing the best thick kapton tape

Thickness

Thickness is the point of this guide, and the listings are thin on it. The BOMEI PACK roll states 2.36 mil thick, the thickest single figure here. The TekLine roll states 1 mil polyimide film with 1.5 mil silicone adhesive. The other listings state no thickness figure, so compare them on width and length instead.

Width and length

Width decides how much surface each pass covers. The CCHUIXI and BOMEI PACK rolls are 2 in wide, the CoYlBod rolls are 1 in, the TekLine roll is 3/4 in, and the MYJOR pack covers 1/4, 1/2, 3/4 and 1 in. Lengths run 33 m on the CoYlBod rolls and 36 yards on the CCHUIXI and TekLine rolls, with 108 ft on the BOMEI PACK roll.

Adhesive

Every full-data listing uses a silicone adhesive, and each one promises no residue on removal. The CCHUIXI, BOMEI PACK and CoYlBod listings all name silicone adhesive, and the TekLine listing names 1.5 mil silicone adhesive. The MYJOR title states no adhesive type. Silicone adhesive releases cleanly, which is what matters for masking.

Heat resistance

Heat resistance is stated as 500 F (260 C) on the CCHUIXI, BOMEI PACK and CoYlBod listings, and as 500 F on the MYJOR title. The BOMEI PACK listing rates that figure for half an hour. The TekLine listing states no heat temperature figure, only that the tape will not burn or wrinkle.

Uses: 3D printer beds, soldering and sublimation

The CCHUIXI listing names 3D printer heated beds, soldering iron tips and sublimation printing. The BOMEI PACK listing names 3D printing, soldering and sublimation, with H-class motor and transformer coil insulation. The CoYlBod listing names heat press, T-shirt work, sublimation, masking and soldering. The TekLine listing names no uses. The MYJOR title names PCB soldering, 3D printer beds and CPU protection.

Safety

Kapton tape handles heat, but the surfaces it covers stay hot. Let heated beds and soldering irons cool before touching them, and ventilate the room when soldering.

Project Match

  • 3D printer beds: the BOMEI PACK roll and the CCHUIXI roll, both 2 in wide with silicone adhesive.
  • Soldering and PCB work: the MYJOR 4-roll pack, with 4 widths for boards, and the CoYlBod rolls for masking circuit boards.
  • Sublimation and heat press: the CoYlBod rolls and the CCHUIXI roll, both listed for sublimation.
  • Fine masking: the TekLine roll, 3/4 in wide with a stated 1 mil film.
  • Electrical insulation: the BOMEI PACK roll, listed for H-class motor and transformer coil insulation.

How the scores add up

Each tape is scored on performance, build, value, safety and warranty, with the weights published on the How We Pick page. A spec the listing does not publish scores nothing. No listing states a warranty term, so no pick scores on warranty.

Product HQ Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
BOMEI PACK Polyimide 9.6 32 21 21 5 0
CCHUIXI Kapton 2 in 9.6 29 21 20 5 0
CoYlBod Polyimide 1 in 9.5 28 20 20 5 0
TekLine Gold Kapton 9.5 27 20 19 4 0

We translate weighted points into a score with 9.2 as its floor and 9.8 as its cap; the straight-line conversion keeps the ranking exactly.

FAQ: lasers and CNC

What is Kapton tape?

Kapton tape is a polyimide film tape with a silicone adhesive, made for high heat work. The listings here name 3D printer beds, soldering, electrical insulation, masking and sublimation among its uses.

How thick is Kapton tape?

The BOMEI PACK roll states 2.36 mil thick, and the TekLine roll states 1 mil polyimide film with 1.5 mil silicone adhesive. The other listings state no thickness figure.

What width Kapton tape should I buy?

The CCHUIXI and BOMEI PACK rolls are 2 in wide, the CoYlBod rolls are 1 in, the TekLine roll is 3/4 in, and the MYJOR pack covers 1/4, 1/2, 3/4 and 1 in. A wider roll covers a printer bed in fewer passes.

Does Kapton tape leave residue?

Each full-data listing promises no residue on removal, and the TekLine listing adds that residues are non-corrosive. The MYJOR title promises a clean peel with no residue.

What temperature can Kapton tape handle?

The CCHUIXI, BOMEI PACK and CoYlBod listings state 500 F (260 C), and the MYJOR title states 500 F. The BOMEI PACK listing rates that figure for half an hour, and the TekLine listing states no heat temperature figure.

Related: the best Kapton tape rolls, best thin Kapton tape, best Kapton tape for heaters, best clear Kapton tape, best small Kapton tape, Kapton tape vs painter’s tape for 3D printing, best 3D printer bed adhesive and best heat gun for 3D printing.

More buying guides

3D Printers ·

Kapton Tape Price: What to Expect

Kapton tape price follows width, length, roll count and heat limits, so this guide explains what changes the amount and which rolls fit printing,…

3D Printers ·

Kapton Tape Temperature Rating Explained

MYJOR states 500F continuous and 536F in short peaks, the highest figures here, so match the stated figure to your soldering, printing or masking…