Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Filament Dryer for Pa6 Cf (2026): 5 Picks for Nylon Prints

Five filament dryers for PA6-CF nylon, from a dual-zone four-spool dryer with annealing to two basic Creality dryers, compared by temperature, capacity and humidity control.

Best Filament Dryer for Pa6 Cf (2026): 5 Picks for Nylon Prints
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1SUNLU S4 ProBest OverallSUNLU S4 Pro9.6/10View on Amazon
  2. 2GEEETECH D1Best for PA PrintsGEEETECH D19.6/10View on Amazon
  3. 3GIANTARM DryerBest High TemperatureGIANTARM Dryer9.5/10View on Amazon

PA6-CF is nylon filled with carbon fiber, and it drinks in moisture from the air. Wet nylon prints with popping, stringing and weak layers, and a spool left open on a shelf only gets worse. A dryer made for nylon gives the filament a hot, dry place to sit before and during a print, so the material feeds cleanly. This guide compares filament dryers for that job and names the best filament dryer for pa6 cf for makers who print functional nylon parts.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Quick picks

  • Best Overall SUNLU S4 Pro: Four 1 kg spools, dual 45-85°C zones, annealing mode and automatic humidity control. Check price on Amazon
  • Best for PA Prints GEEETECH D1: PA named among its materials, sealed storage, dual temperature monitoring and an 85°C maximum. Check price on Amazon
  • Best High Temperature GIANTARM Dryer: 90°C maximum setting with dual fans, 360° heating and a 2.8-inch touchscreen. Check price on Amazon

Machines on the list

SUNLU 3D Printer Filament Dryer S4 Pro,Dual-Zone

SUNLU 3D Printer Filament Dryer S4 Pro,Dual-Zone

SUNLU9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A dual-zone dryer for four 1 kg spools, with independent 45-85°C zones, an annealing mode and automatic humidity control.

Pros

  • Dries four 1 kg spools at once, with 2 kg of capacity on each side
  • Dual-zone 45-85°C control dries different filaments at the same time
  • Annealing mode holds 70-85°C for 2-3 hours for functional filament models
  • Names PA and nylon among its materials, with PLA, PETG, ABS, TPU and PC

Cons

  • At 10.36 lb it is the heaviest dryer in this lineup to lift and move
  • External dimensions of 458 x 218 x 340 mm need the most bench space here
  • Annealing a model takes 2-3 hours at 70-85°C, so it is a long extra step
  • Its 380W heater draws more power than the 150W heaters of the GIANTARM and GEEETECH
GEEETECH D1 3D Filament Dryer, Max 85°C

GEEETECH D1 3D Filament Dryer, Max 85°C

Geeetech9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A sealed modular dryer with 30-85°C control, dual-fan 360° heating and a 2.8-inch touchscreen.

Pros

  • Names PA among its materials, with PLA, PETG, ABS, TPU, PC, ASA, PP and PVA
  • Adjustable 30-85°C drying with 1-99 hour timing
  • Sealed box with silicone rings keeps filaments dry in storage
  • Dual temperature monitoring and a heat insulation chamber prevent overheating

Cons

  • Maximum temperature is 85°C, below the 90°C setting of the GIANTARM
  • No warranty term is stated
  • The hygrometer must not sit inside the dryer during operation, or its sensor is damaged
  • At 11.81 x 4.57 x 11.81 in it takes shelf room
GIANTARM Filament Dryer,Upgraded 150W PTC 3D

GIANTARM Filament Dryer,Upgraded 150W PTC 3D

GIANTARM9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A modular dryer with a 90°C maximum setting, dual fans, 360° heating and a 2.8-inch touchscreen.

Pros

  • Maximum temperature setting of 90°C, the highest setting here
  • Dual fans and 360° circulating hot air for even heating
  • 2.8-inch touchscreen with parameter memory and power-off memory
  • 1+N modular design lets one heating base support multiple drying boxes

Cons

  • PA and nylon are not named among its supported materials
  • Average internal temperature is 85°C when the dryer is set to 90°C
  • No warranty term is stated
  • The hygrometer must not be placed under heating conditions
2026 New Official CREALITY Space Pi Filament

2026 New Official CREALITY Space Pi Filament

Creality9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 110W PTC hot-air filament dryer with a fan, a 3.7-inch touch screen, one-key presets for 12 filament types and real-time humidity and temperature monitoring.

Pros

  • 110W PTC heater with 360 degree hot-air circulation and a fan
  • One-key presets for 12 filament types, 45 degrees C to 70 degrees C
  • Real-time humidity and temperature display on a 3.7-inch touch screen
  • 1 Year Manufacture warranty stated in the spec table

Cons

  • No spool capacity stated in the listing
  • No drying timer stated in the listing
  • Filament sizes stated are 1.75 and 2.85 mm only
  • Touch screen is 3.7-inch, smaller than the 4.6-inch SUNLU screen
2026 New Official CREALITY Filament Dryer Space Pi

2026 New Official CREALITY Filament Dryer Space Pi

Creality9.4/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single-spool dryer with a 360 degree fan, a 65 degree maximum and two rollers for printing while drying.

Pros

  • Two rollers allow printing while drying
  • Reaches 65 degrees within 15 minutes
  • Real-time humidity and drying countdown on the display
  • Thermal insulation cotton on both sides

Cons

  • Maximum temperature of 65 degrees is the lowest here
  • Timer range of 0 to 24 hours is the shortest here
  • Diameter list covers 1.75mm and 2.85mm only
  • No warranty term is stated

Specs compared

Model HQ Score Max temp Heater Capacity Filament sizes Warranty
SUNLU S4 Pro 9.6/10 85°C 380W PTC Four 1 kg spools 1.75mm, 2.85mm, and 3.00mm Not stated
GEEETECH D1 9.6/10 85°C 150W PTC Not stated 1.75/2.85 mm Not stated
GIANTARM Dryer 9.5/10 90°C setting 150W PTC Not stated 1.75/2.85 mm Not stated
Creality Space Pi SE 9.4/10 65°C PTC 1 kg 1.75/2.85 mm Not stated
Creality Space Pi 9.5/10 Not stated 110W PTC Not stated 1.75/2.85 mm Not stated

We give each product’s specs as its manufacturer rates them; listings read 21 November 2026.

Most dryers here stop short of nylon heat

PA6-CF is a nylon filament, and nylon is the material that pushes dryer temperatures hardest in this lineup. The GIANTARM sets up to 90°C, with an 85°C average inside at that setting, while the SUNLU and the GEEETECH reach 85°C. The Creality Space Pi SE tops out at 65°C, and the Creality Space Pi names no maximum temperature. A 65°C ceiling leaves less headroom than an 85°C or 90°C setting when the filament is nylon, so the two Creality dryers sit at the bottom of this ranking on temperature alone. The SUNLU adds annealing at 70-85°C, which suits functional nylon parts after printing.

How to pick the best filament dryer for pa6 cf

Match the maximum temperature to nylon

Start with the highest temperature each dryer offers. The GIANTARM sets up to 90°C, though its average inside is 85°C at that setting. The SUNLU and the GEEETECH each reach 85°C, with the SUNLU holding 45-85°C across two independent zones. The Creality Space Pi SE reaches 65°C, and the Creality Space Pi names no maximum temperature, so it cannot be compared on heat. For PA6-CF, the dryers that reach 85°C or more give the most headroom.

Count the spools you dry at once

The SUNLU dries four 1 kg spools at once, with 2 kg of capacity on each side, so a full set of nylon and support material can dry together. The GEEETECH supports multi-spool alternate drying with detachable chambers, and the GIANTARM uses a 1+N modular design where one heating base supports multiple drying boxes. The Creality Space Pi SE is built for 1 kg spools. Match the count to how many spools you keep open at once.

Humidity control and sealed storage

Drying is only half the job; the spool must stay dry until it feeds. The SUNLU controls humidity automatically, activating when the chamber reaches 30-50% humidity and stopping once it drops to 25%. The GIANTARM offers timed drying and constant humidity control. The GEEETECH seals its box with silicone rings and reinforced buckles to keep humid air out during storage. The two Creality dryers name no humidity control, so they rank below the other three here.

Filament sizes and materials

Check the sizes and materials each dryer names. The SUNLU fits 1.75, 2.85 and 3.00 mm filament and names PA and nylon among its materials, with PLA, PETG, ABS, TPU and PC. The GEEETECH fits 1.75 and 2.85 mm and names PA among PLA, PETG, ABS, TPU, PC, ASA, PP and PVA. The GIANTARM fits 1.75 and 2.85 mm and names PLA, PETG, ABS, TPU and ASA, with no PA named. The Creality Space Pi SE names nylon, and the Creality Space Pi names PA, both for 1.75 and 2.85 mm filament.

Safety

Both the GIANTARM and the GEEETECH warn against placing a hygrometer inside the dryer during operation, since the heat damages its sensor. Keep the hygrometer outside the chamber and read temperature and humidity on the dryer screen instead.

Project Match

  • Functional PA6-CF parts: SUNLU S4 Pro, with PA named in its materials and an annealing mode at 70-85°C.
  • Everyday PLA and PETG drying: GIANTARM Dryer or GEEETECH D1, with 2.8-inch touchscreens and 360° heating.
  • Long storage between prints: GEEETECH D1, with a sealed box and silicone sealing rings.
  • Several spools at once: SUNLU S4 Pro, with four 1 kg spools and 2 kg of capacity on each side.
  • Drying while printing: SUNLU S4 Pro, which dries filament during the printing process.

How the scores add up

Each dryer is scored on performance, build, value, safety and warranty, with the weights published on the How We Pick page. A spec the listing does not publish scores nothing.

Product HQ Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
SUNLU S4 Pro 9.6 33 22 21 4 0
GEEETECH D1 9.6 30 21 20 5 0
GIANTARM Dryer 9.5 29 20 20 3 0

Point totals are scaled so the weakest reads 9.2 and the strongest 9.8, with everything between kept in order.

FAQ: lasers and CNC

What temperature dries PA6-CF filament?

The dryers here offer maximum settings from 65°C on the Creality Space Pi SE to a 90°C setting on the GIANTARM, with an 85°C average inside at that setting. The SUNLU and the GEEETECH reach 85°C. The Creality Space Pi names no maximum temperature.

Can I dry more than one spool at once?

The SUNLU dries four 1 kg spools at once, with 2 kg on each side. The GEEETECH supports multi-spool alternate drying, and the GIANTARM uses a 1+N modular design with one heating base for multiple boxes. The Creality Space Pi SE is built for 1 kg spools.

Do these dryers work while the printer runs?

The SUNLU dries filament during the printing process, and the Creality Space Pi SE is also built for drying during printing. For the GIANTARM, GEEETECH and Creality Space Pi, no drying-during-printing use is stated.

What filament sizes fit these dryers?

The SUNLU fits 1.75, 2.85 and 3.00 mm filament. The GIANTARM, GEEETECH, Creality Space Pi SE and Creality Space Pi each fit 1.75 and 2.85 mm filament.

Related: FDM 3D printing filament, filament storage racks, ABS filament for enclosed printers and the 3D printers hub.

More buying guides

3D Printers ·

Is a Filament Dryer Worth It?

A practical guide to whether a filament dryer is worth it: what wet filament does, how dryers work, and when sealed storage is enough.