Best Double Filament Dryer Box (2026): 5 Picks Compared
5 dual and multi-spool filament dryer boxes from 55°C to 90°C, compared by chambers, heater power, timers, safety statements and warranty.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallCreality SpacePi X4L9.7/10View on Amazon - 2
Highest TemperatureTEQStone D1 Dryer9.6/10View on Amazon - 3
Best Two-Spool PickLANDU Double Dryer9.5/10View on Amazon - 4
Quickest Heat-UpCreality SpacePi SE9.4/10View on Amazon - 5
Best Compact PickeSUN eBOX Lite9.3/10View on Amazon
Damp filament ruins prints in quiet ways: stringing across a flat face, layers that will not stick, a spool that snaps when it bends. A double filament dryer box holds two spools in warm, dry air so the filament that feeds the printer stays dry between jobs. This guide compares the best double filament dryer box picks for makers who run more than one spool at a time, using only what each listing states about chambers, heat, timers, safety and warranty.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall Creality SpacePi X4L: Two independent chambers, 4 spools, 75°C heat and a 1 year warranty. Check price on Amazon
- Highest Temperature TEQStone D1 Dryer: A 150W PTC heater that runs to 90°C, with active dehumidification and a touchscreen. Check price on Amazon
- Best Two-Spool Pick LANDU Double Dryer: Two 1KG spools at once, 4 filament holes for 2 printers, and a 1 Year warranty. Check price on Amazon
- Quickest Heat-Up Creality SpacePi SE: 65°C in 15 minutes with a humidity display and a 0 to 24 hour timer. Check price on Amazon
- Best Compact Pick eSUN eBOX Lite: A small 1.65 pound box with a transparent lid for 1 kg spools. Check price on Amazon
Machines on the list

Creality Filament Dryer Box 4 Spool
A 4-spool dryer with two independent heating chambers, 200W plus 200W PTC heaters, a 75°C top temperature and active dehumidification, with a 1 year warranty.
Pros
- Two independent chambers dry PLA, PETG, ABS, TPU and Nylon at separate temperatures.
- 75°C top temperature suits engineering filaments such as PAHT, PC and PA.
- Active dehumidification plus a sealed lid with a silicone gasket.
- Overheat auto-shutoff, flame-retardant ABS housing and anti-tip power cut, with a 1 year warranty.
Cons
- At 12.9 pounds it is the heaviest box in this guide.
- No timer range is stated in the listing.
- The listing claims 0% moisture intrusion, which no home setup can verify.
- The stated 40% energy saving applies only to single-chamber saver mode.

D1 3D Printer Filament Dryer Box
A modular dryer with a 150W PTC heater, a 90°C top temperature, active dehumidification and a 2.8 inch touchscreen, with one heating base that supports extra boxes.
Pros
- 90°C top temperature, the highest in this guide, with about 85°C inside the chamber.
- Active moisture exhaust with dual fans, stated to improve drying efficiency by 20% to 30%.
- Modular 1+N design: one heating base supports extra drying boxes.
- 2.8 inch touchscreen with a 55° tilt, power-off resume and custom parameter memory.
Cons
- No warranty term is stated.
- No timer range is stated.
- The 90°C figure is measured at the air outlet; the chamber averages about 85°C.
- Dries one spool per box; extra boxes are needed for more spools.

LANDU Filament Dryer 3D Printer Filament Dry Box,2
A two-spool dryer with 4 filament holes, hot-air heating to 70°C, a 0 to 24 hour timer and a 1 Year warranty.
Pros
- Dries two 1KG spools at once and feeds 2 printers through 4 filament holes.
- Heats to 50°C in 5 mins and 70°C in 15 mins, with a 50°C to 70°C range.
- Timer runs 0 to 24 hours, with separate temperature and time settings.
- 1 Year warranty stated in the spec table.
Cons
- No safety feature is stated.
- 70°C top temperature is below the 90°C and 75°C figures of the two hotter boxes.
- No display or humidity readout is stated.
- No spool size beyond 1KG is stated.

Creality Filament Dryer Box Space Pi SE 2026
A single-spool dryer with PTC heating and a fan, reaching 65°C in 15 minutes, with a 0 to 24 hour timer and a real-time humidity display.
Pros
- Heats to 65°C in 15 minutes with a hot-air circulation fan.
- Timer runs 0 to 24 hours and temperature runs 45°C to 65°C.
- Real-time humidity and drying status display with a countdown timer.
- Sealed storage keeps spools dry between print sessions.
Cons
- No warranty term is stated; the spec table lists 0.
- No safety feature is stated.
- Single-spool capacity; no multi-spool mode is stated.

eSUN eBOX Lite Upgraded 3D Printing Filament Dryer
A compact single-spool dryer with a 40°C to 55°C range, a 0 to 18 hour timer and a transparent lid, for 0.5 kg, 0.75 kg and 1 kg spools.
Pros
- Holds 1.75mm, 2.85mm and 3.00mm filament in 0.5 kg, 0.75 kg and 1 kg spools.
- Transparent lid lets you check the filament without opening the lid.
- At 1.65 pounds it is the lowest-weight box in this guide.
- Low-noise turbo fan for quiet running at night.
Cons
- 55°C top temperature is the lowest in this guide.
- Takes 2 hours to reach 50°C to 55°C, longer than any other box in this guide.
- No warranty term is stated.
- No safety feature is stated.
Other machines to compare
Creality Filament Dryer Box 4 SpoolsCheck price on Amazon
Creality 2026 New Upgrade Filament Dryer Box ProCheck price on Amazon
Comgrow Filament Dryer Box for 1.75/2.85mm PLA PETG TPU ABSCheck price on Amazon
SUNLU 3D Printer S4 Pro Filament Dryer BoxCheck price on Amazon
QIDI Box Multi-Color 3D Printing System for QIDI PLUS4 3DCheck price on Amazon
Specs compared
| Model | HQ Score | Max temp | Capacity | Heater | Timer | Warranty |
|---|---|---|---|---|---|---|
| Creality SpacePi X4L | 9.7/10 | 75°C | 4 spools, 2 chambers | 200W + 200W PTC | Not stated | 1 year |
| TEQStone D1 Dryer | 9.6/10 | 90°C | 1 spool per box | 150W PTC | Not stated | Not stated |
| LANDU Double Dryer | 9.5/10 | 70°C | 2 spools | Hot air with fan | 0-24 hours | 1 year |
| Creality SpacePi SE | 9.4/10 | 65°C | 1 spool | PTC with fan | 0-24 hours | Not stated |
| eSUN eBOX Lite | 9.3/10 | 55°C | 200 x 73 mm spool | PI heating arc | 0-18 hours | Not stated |
Size and performance figures are the brand’s ratings quoted from listings on 12 November 2026. Temperatures are the top temperature each listing states.
What the listings tell you, and what they leave out
We read 5 filament dryer listings for this guide. Only 2 stated a warranty term, and only 2 printed a safety feature set worth scoring: overheat shutoff on one, fault monitoring on the other. The other 3 listings stated no safety feature and no warranty term, so they score nothing on those two criteria.
Treat every temperature here as the top figure the listing states, and check the timer range before a long drying run: two of the 5 listings state a timer that runs to 24 hours, one runs to 18 hours, and two state no timer at all.
How to pick the best double filament dryer box
Two chambers or one
A dual-chamber box dries two materials at different temperatures at once. The Creality SpacePi X4L has two isolated chambers with a 200W PTC heater in each, and it holds 4 spools. The TEQStone D1 takes a modular route: one heating base supports extra drying boxes, so you dry one spool while the rest sit in sealed storage. The LANDU dries two 1KG spools in one box and feeds 2 printers through 4 filament holes.
Top temperature
Top temperature decides which filaments a box can dry. The TEQStone D1 runs to 90°C, the Creality SpacePi X4L to 75°C, the LANDU to 70°C, the Creality SpacePi SE to 65°C, and the eSUN eBOX Lite to 55°C. The D1 and the X4L name engineering filaments in their lists: the D1 lists PC and PA, and the X4L lists PAHT, PC and PA.
Active drying vs sealed storage
Two boxes state active dehumidification. The X4L pairs it with a sealed lid and a silicone gasket, and the D1 pairs an active moisture exhaust with dual fans. The other boxes lean on heat plus a closed box: the eSUN eBOX Lite has a transparent lid, and the SpacePi SE states dust and moisture-proof sealed storage. A sealed lid keeps dry filament dry; active exhaust moves damp air out while drying runs.
Timers and displays
Two boxes state a timer that runs 0 to 24 hours: the LANDU and the SpacePi SE. The eSUN eBOX Lite runs 0 to 18 hours, with a mode button that sets heat from 1 to 3 and then the time. The D1 skips a timer in its listing and puts the controls on a 2.8 inch touchscreen, while the SpacePi SE shows humidity and drying status with a countdown timer.
What a dryer box will not do
A dryer box dries the filament its listing names, and no listing in this guide states a spool weight above 1 kg. A dryer box is not a printer enclosure, and it will not dry a spool that sits open on a shelf: the spool has to sit inside the closed box, with the lid shut, for the dry air to do its work.
Project Match
- Signs and cut parts in PLA and PETG: Creality SpacePi X4L, with 4 spools on hand and dual chambers.
- Engineering filaments such as PAHT, PC and PA: TEQStone D1, with a 90°C top temperature.
- Two printers fed at once: LANDU Double Dryer, with 4 filament holes.
- One spool kept dry beside the printer: Creality SpacePi SE, with a humidity display.
- A compact box for 1 kg spools: eSUN eBOX Lite, with a transparent lid.
How the scores add up
Each dryer is scored on performance, build, value, safety and warranty. How we pick explains the weights. A spec the listing does not publish scores nothing.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Creality SpacePi X4L | 9.7 | 30 | 21 | 19 | 8 | 3 |
| TEQStone D1 Dryer | 9.6 | 32 | 21 | 20 | 7 | 0 |
| LANDU Double Dryer | 9.5 | 28 | 19 | 20 | 0 | 3 |
| Creality SpacePi SE | 9.4 | 29 | 20 | 20 | 0 | 0 |
| eSUN eBOX Lite | 9.3 | 26 | 18 | 19 | 0 | 0 |
We translate weighted points into a score with 9.2 as its floor and 9.8 as its cap; the straight-line conversion keeps the ranking exactly.
FAQ: lasers and CNC
Can a double filament dryer box dry two spools at once?
Yes, if the listing states it. The Creality SpacePi X4L holds 4 spools in two chambers, and the LANDU dries two 1KG spools at once. The TEQStone D1 dries one spool per box and adds boxes on one heating base, while the Creality SpacePi SE and the eSUN eBOX Lite are single-spool boxes.
What temperature should I dry PLA at?
The listings state drying ranges, and each box lets you set the temperature. The eSUN eBOX Lite runs 40°C to 55°C, the Creality SpacePi SE runs 45°C to 65°C, and the LANDU runs 50°C to 70°C. Pick the range that covers the filament you print with.
Do I need active dehumidification?
Two boxes in this guide state it: the Creality SpacePi X4L and the TEQStone D1. The other boxes use heat plus a closed lid and sealed storage. If your shop runs humid, a box that states active dehumidification or an active moisture exhaust is the safer pick.
Can I print while the filament dries?
The Creality SpacePi SE states a controlled drying environment during storage and printing, and the LANDU feeds 2 printers through 4 filament holes while drying runs. The other listings do not state feed-through printing, so check the listing before you plan a print from a drying spool.
How long does a drying run take?
Heat-up times vary. The Creality SpacePi SE heats to 65°C in 15 minutes, the LANDU heats to 50°C in 5 mins and 70°C in 15 mins, and the eSUN eBOX Lite takes 2 hours to reach 50°C to 55°C. The LANDU and the SpacePi SE state timers that run 0 to 24 hours, and the eSUN eBOX Lite states 0 to 18 hours.
Related: the 3D printers hub, silica gel desiccant packs for filament, nozzle cleaning kit, and CoreXY vs bed slinger.




