Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Types of Stepper Motors for CNC and Laser Builds

Bipolar Nema 17 motors explained, with frame size, step angle and holding torque compared across four motors for CNC routers and laser builds.

Types of Stepper Motors for CNC and Laser Builds
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1YEJMKJ Nema 17 Stepper Motor 42x38mm 0.47NmYEJMKJ Nema 17 Stepper Motor 42x38mm 0.47Nm9.6/10View on Amazon
  2. 2STEPPERONLINE Nema 17 Stepper Motor 2A 55NcmSTEPPERONLINE Nema 17 Stepper Motor 2A 55Ncm9.5/10View on Amazon
  3. 3STEPPERONLINE Nema 17 Stepper Motor Bipolar 1.5ASTEPPERONLINE Nema 17 Stepper Motor Bipolar 1.5A9.5/10View on Amazon
  4. 4iMetrx Nema 17 Stepper Motor 42x60mm 2.1A 2 PhaseiMetrx Nema 17 Stepper Motor 42x60mm 2.1A 2 Phase9.4/10View on Amazon

A router that stalls halfway through a cut, or a laser head that drifts off its path, often traces back to the motors that move each axis. Types of stepper motors differ in how the coils are wired, how large the frame is, and how much holding torque they hold when stopped, and those differences decide whether a machine moves smoothly or skips steps. This guide explains the types of stepper motors used in CNC routers and laser builds, then compares the motors suited to small machines.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

YEJMKJ Nema 17 Stepper Motor 42x38mm 0.47Nm

YEJMKJ Nema 17 Stepper Motor 42x38mm 0.47Nm

YEJMKJ9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A Nema 17 bipolar motor with 0.47Nm holding torque, a 24mm shaft and a 1m cable, with stated safety ratings and a 12-24V DC range.

Pros

  • 0.47Nm (66.56oz-in) holding torque stated in the listing
  • Shaft length 24mm with 5mm diameter and a D-cut length of 24mm
  • Stated safety ratings: insulation class UL B, dielectric strength 500V AC for 1 minute
  • Stated operating range of 0-600 RPM, up to 1800 RPM for closed-loop systems

Cons

  • No warranty term in the listing
  • Single motor, not a multi-pack
  • Title rounds the body to 42x38mm while the bullets state 42x42x37.5mm
  • Holding torque is stated in Nm, so it reads differently from the Ncm figures on the other listings
STEPPERONLINE Nema 17 Stepper Motor 2A 55Ncm

STEPPERONLINE Nema 17 Stepper Motor 2A 55Ncm

STEPPERONLINE9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-pack of Nema 17 bipolar motors with 55Ncm holding torque, 2A per phase and a 1m cable and connector.

Pros

  • 55Ncm holding torque, the highest Ncm figure in this guide
  • 3-pack covers three axes with a single listing
  • 2A rated current per phase with 1.3 ohms resistance
  • 1m cable and connector included

Cons

  • No warranty term in the listing
  • Spec table lists cube dimensions of 1.65 inches on each side, which do not match the 42x42x48mm body in the title
  • No shaft size stated
  • No operating temperature or speed range stated
STEPPERONLINE Nema 17 Stepper Motor Bipolar 1.5A

STEPPERONLINE Nema 17 Stepper Motor Bipolar 1.5A

STEPPERONLINE9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-pack of Nema 17 bipolar motors with 42Ncm holding torque, 1.5A per phase and a 1m cable and connector.

Pros

  • 42Ncm holding torque stated in the listing
  • 3-pack covers three axes with a single listing
  • 1.5A rated current per phase with 2.3 ohms resistance
  • 1m cable and connector included

Cons

  • No warranty term in the listing
  • Lower holding torque than the 55Ncm motor in this guide
  • No shaft size stated
  • No operating temperature or speed range stated
iMetrx Nema 17 Stepper Motor 42x60mm 2.1A 2 Phase

iMetrx Nema 17 Stepper Motor 42x60mm 2.1A 2 Phase

iMetrx9.4/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single Nema 17 bipolar motor, 42x60mm, 2.1A, with a 1m cable for 3D printer and CNC use.

Pros

  • 2.1A rated current, the highest current figure in this guide
  • 42x60mm body, the longest body in this guide
  • Maker claims 20-25% higher torque than normal motors
  • 1m cable included

Cons

  • No warranty term in the listing
  • No holding torque figure in Ncm or Nm is stated
  • Spec table lists a depth of 1.5 inches, which does not match the 42x60mm body in the title
  • Single motor, not a multi-pack

Types of Stepper Motors

Every motor in this guide is a bipolar two-phase Nema 17 motor, and that combination is the common choice for small CNC routers and laser engravers. Bipolar motors drive current through the full winding of each phase, reversing its direction to change polarity, while unipolar motors use a center tap on each coil and switch half of the coil at a time. Hybrid motors pair a permanent magnet rotor with toothed steel caps.

Frame size is the other split that matters. Nema 17 describes a square motor face, and each listing here states a body of 42mm across the face, with lengths from 42x42x37.5mm to 42x60mm. Step angle is the last split: each motor here lists a step angle of 1.8 degrees, which gives 200 steps per revolution.

How to Match a Stepper Motor to a CNC or Laser Build

Start with holding torque, because it decides whether the motor holds position under cutting load. Three of the motors in this guide state a holding torque: 42Ncm, 55Ncm and 0.47Nm; the fourth states none. Then check rated current per phase, listed here from 1.5A to 2.1A, and pair the motor with a driver that can supply that current; the best stepper motor driver for Nema 17 guide covers driver picks for this frame size.

Frame size decides fit: every motor here has a 42mm square face, so the mount stays the same while the body length changes. Shaft size decides the pulley or coupler, and the YEJMKJ listing states a 24mm shaft with a 5mm diameter, while the other listings leave shaft size unstated. For a wider view of frame sizes, see the stepper motor size guide, and the closed loop vs open loop stepper CNC comparison explains when feedback helps.

Nema 17 Stepper Motors for CNC and Laser Builds

Each motor below moves an axis of a small CNC router or laser engraver. The cards carry the full specs, pros and cons for each motor.

FAQ: lasers and CNC

What is the difference between bipolar and unipolar stepper motors?

Bipolar motors drive current through each phase in turn, while unipolar motors switch half of each center-tapped coil at a time. The listings in this guide are all bipolar two-phase motors.

What does Nema 17 mean?

Nema 17 names a frame size with a square face 42mm across. Every motor in this guide states a 42mm face, with body lengths from 42x42x37.5mm to 42x60mm.

How much holding torque does a small CNC router need?

No single figure fits every machine, since gantry weight and cutting load change the answer. Three of the motors in this guide state a holding torque: 42Ncm, 55Ncm and 0.47Nm; the fourth states none.

Do stepper motors need a driver?

Yes, a stepper motor needs a driver between the controller and the motor, and the driver must suit the rated current per phase. The best stepper motor driver for Nema 17 guide and the best stepper driver for X-Carve guide cover driver picks for this frame size.

Can a Nema 17 motor run a laser engraver axis?

Yes, Nema 17 motors move the axes of many small laser engravers and desktop CNC routers. The choice comes down to holding torque, body length and whether the driver can supply the rated current, such as 1.5A or 2.1A as listed here.

Related: the stepper motor size guide, stepper motor vs servo motor CNC, closed loop vs open loop stepper CNC and planetary gearbox vs direct drive stepper CNC.

More buying guides

CNC Routers ·

Stepper Motor Troubleshooting for CNC Machines

A practical stepper motor troubleshooting guide for CNC machines: trace stalls, missed steps and overheating to power, wiring and driver settings, then pick the…