Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Cost of Stepper Motor: What to Expect to Pay

A plain guide to what drives stepper motor prices for CNC routers, which specs matter, and how to compare listings before buying.

Cost of Stepper Motor: What to Expect to Pay
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1STEPPERONLINE TE Series Digital Stepper Driver 1.0-4.2ASTEPPERONLINE TE Series Digital Stepper Driver 1.0-4.2A9.7/10View on Amazon
  2. 2MAKERELE TB6600 Stepper Motor Driver for Nema 17 23 StepperMAKERELE TB6600 Stepper Motor Driver for Nema 17 23 Stepper9.7/10View on Amazon
  3. 3Tofelf Stepper Motor DriverTofelf Stepper Motor Driver9.6/10View on Amazon

A CNC router that stalls mid-cut, loses position on a long carve, or groans through every pass can point back to the motor driving the gantry. Before ordering a replacement or planning a build, it helps to know what sets the cost of stepper motor hardware apart, and which specs actually move the price. This guide walks through the cost drivers in plain order, using real listing figures, so the next motor fits the machine and the spending plan.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

Listings change, and prices move with stock, sellers and seasons, so this guide gives no set price figure. Instead it explains what drives the cost of stepper motor hardware, with the exact figures listings state for torque, current, size and shaft.

Step 1: Start with torque, not the frame name

Torque decides whether the motor can move the gantry and hold position under load. Listings for NEMA 23 motors state holding torque from 0.7 Nm (101 oz.in) up to 3 Nm (425 oz.in), with common mid-range figures of 1.24 Nm (175.6 oz.in), 1.9 Nm (269 oz.in) and 2.4 Nm (339.79 oz.in). A light desktop machine asks less of the motor than a large gantry cutting hardwood, so match the torque figure to the load the axis carries, not to the biggest number on the page.

Step 2: Match the frame and body length to the machine

Every listing in this guide uses the NEMA 23 frame, which measures 57 mm across the face, so the frame name alone tells little about the price. Body length is where the listings differ: stated lengths in millimetres run from 41 mm to 82 mm, and inch listings state 2.2 inches, 3.0 inches and 4.45 inches for the body depth. Longer bodies in these listings go with higher torque figures, so a short motor that looks like a bargain may simply be a lower-torque model. Check the frame chart in the stepper motor size guide before assuming any NEMA 23 motor drops into any mount.

Step 3: Check current, voltage and the driver

Current and voltage shape the motor choice and the driver it needs. The listings state rated current of 2.4 A, 2.8 A, 4.0 A and 4.2 A, and driving voltage of 24 V, 24-48 VDC and 24-50 VDC, with a suggested 36 VDC for the 4.0 A model. A listing for the 2.8 A, 1.9 Nm model recommends a driver with voltage of 24-50 VDC and at least 3.5 A current. A driver that cannot supply the rated current leaves torque unused, while a driver rated far above the motor’s rated current gives that motor nothing extra. See the stepper driver guide for X-Carve for what to look for in a driver.

Step 4: Check the shaft, wiring and step angle

The shaft has to fit the pulley or coupler already on the machine. Listings state shaft diameters of 6.35 mm, 8 mm and 10 mm, and six of the seven listings here state a 4-wire bipolar layout with a 1.8 degree step angle, or 200 steps per revolution; the HobbyUnlimited listing states neither the wiring nor the step angle. An 80 cm cable comes with the 0.7 Nm model, which helps when the control box sits away from the axis. Measure the existing shaft and coupler before ordering, because a shaft that does not fit the coupler already fitted means ordering a different coupler or returning the motor.

Step 5: Compare like with like on packs and weight

Pack size changes the comparison, so compare the same quantity. Several listings sell a pack of 3 motors, while others sell a motor on its own. The 3-motor pack of the 3 Nm model lists an item weight of 11.46 pounds for the pack of 3, while a listing for a single 1.24 Nm motor lists 1.5 pounds and a single 1.9 Nm motor lists 2.3 pounds. Weight also hints at build: the 1.9 Nm model with an 8 mm shaft lists 2.4 lb, or 1.1 kg. Resistance figures sit at 0.9 ohms, 0.65 ohms and 1.13 ohms across the listings; check the figure for the exact model, since it varies with the winding.

Step 6: Add the parts around the motor

The motor is only part of the spend. A driver, a power supply that matches the stated voltage, wiring, mounts and couplers all sit around it, and a new shaft size can mean new couplers too. A 4.0 A motor needs a driver and a supply that suit 4.0 A and the stated voltage range, so price the set together rather than the motor by itself. The CNC router table cost guide shows how the wider machine costs stack up around the motion parts.

Step 7: Read the listing, not just the title

Titles, bullets and spec tables do not always agree, and the disagreement matters. A listing for the 0.7 Nm motor states a body size of 2.24 x 2.24 x 1.61 inches in its bullets, while its spec table lists product dimensions of 3.0 inches x 3.0 inches x 3.0 inches. A listing for the 2.4 Nm motor states 57 x 57 x 82 mm in its title, while its spec table lists dimensions of 2.24 inches on each side. Trust the title and bullets over the spec table, and treat a listing with conflicting dimensions as a reason to ask the seller before ordering.

Common mistakes to avoid

  • Buying on torque alone, without checking current, voltage and shaft size.
  • Comparing a pack price with a motor price as if the quantities matched.
  • Ordering a shaft size that does not fit the coupler already fitted.
  • Trusting the spec table when the title and bullets state different dimensions.
  • Forgetting the driver, power supply and couplers when adding up the spend.

Cost of stepper motor: the short version

  1. Pick the torque figure the axis load needs.
  2. Match the NEMA 23 frame and body length to the mount.
  3. Check rated current and voltage, then price a matching driver.
  4. Confirm the shaft diameter, wiring and step angle.
  5. Compare packs with packs and motors with motors.
  6. Add the driver, supply, wiring and couplers to the spend.
  7. Read the title and bullets, and query conflicting dimensions.

Work through the list in order, and the motor that fits the machine costs what it costs for a reason, not by accident.

FAQ: lasers and CNC

How much does a stepper motor cost?

There is no set figure, because the price moves with frame size, torque, current, shaft size and pack quantity. NEMA 23 listings here state torque from 0.7 Nm (101 oz.in) to 3 Nm (425 oz.in), with rated current from 2.4 A to 4.2 A. Compare listings with the same torque, current and quantity, and the spread between them is the real price range for the spec.

What size stepper motor does a CNC router need?

Many CNC routers use the NEMA 23 frame, which measures 57 mm across the face, but frame alone does not settle the choice. Body length, torque, current and shaft diameter all vary within the frame, so check the mount, the load and the driver before ordering. The frame chart on this site maps the frame sizes used on CNC routers.

Is a higher torque stepper motor always better?

Not for every machine. A 3 Nm motor suits a heavy gantry, while a 0.7 Nm motor suits a light axis, and the larger motor draws more current and needs a driver to match. Oversizing the motor means a larger, heavier motor and a driver to match, without improving a cut the smaller motor already handles. Match the torque to the load, not to the largest figure in the listing.

Do I need a driver for a stepper motor?

Yes. A stepper motor needs a driver that supplies its rated current at a suitable voltage. One listing here recommends a driver with voltage of 24-50 VDC and at least 3.5 A current for its 1.9 Nm model, and rated current across the listings runs from 2.4 A to 4.2 A, so match the driver to the exact motor. The stepper driver guide for X-Carve covers what to look for in a driver.

Stepper motor or servo motor for a CNC router?

A stepper motor holds position with a 1.8 degree step angle and 200 steps per revolution, which suits many router builds, while a servo motor suits builds that need closed-loop feedback. The stepper motor versus servo motor guide compares the types for CNC work.

Related: the stepper motor size guide, stepper motor versus servo motor guide, CNC router table cost guide and what a CNC router machine is.

More buying guides

CNC Routers ·

Stepper Motor Troubleshooting for CNC Machines

A practical stepper motor troubleshooting guide for CNC machines: trace stalls, missed steps and overheating to power, wiring and driver settings, then pick the…