Sunlu S1 vs S2 Filament Dryer: Which One Should You Buy?
Two SUNLU filament dryers, the S1 Plus and the S2, compared on heating, display, capacity, filament types and warranty.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SUNLU Filament Dryer Box 2026 New Upgrade S19.7/10View on Amazon - 2
SUNLU Official Filament Dryer S29.7/10View on Amazon
Wet filament strings, clogs and prints with poor adhesion, and a dryer box can help with those problems, per both listings. SUNLU sells the S1 Plus and the S2, and the choice comes down to heating, display, filament types and warranty. This comparison of sunlu s1 vs s2 filament dryer puts the two listings side by side on what each one states.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Verdict: pick the S1 Plus if a stated 1 Year warranty matters most; its heating and display are simpler, but the warranty term is written out. Pick the S2 if you dry PC or want a touch screen and the 70° maximum the listing states; its warranty is stated only as “1” with no unit. Choose by the filament you dry and the warranty you want in writing.
Machines on the list

SUNLU Filament Dryer Box 2026 New Upgrade S1
A fan-design filament dryer with a 2 inch LCD screen and a 35 to 55°C range, sized for 1.75, 2.85 and 3.00 mm filament, with a 1 Year warranty.
Pros
- Fan design speeds up moisture discharge
- 2 inch LCD shows temperature, time and humidity
- 35 to 55°C adjustable range
- 1 Year warranty stated
Cons
- Maximum of 55°C, while the S2 listing states 70° with no unit given
- No PC listed among filament types
- Buttons, not a touch screen
- No heating speed claim stated

SUNLU Official Filament Dryer S2
A filament dryer with 360° heating from a dual heating sheet and fan, a 4.6 inch touch screen and a maximum of 70°, for 1.75, 2.85 and 3.00 mm filament including PC.
Pros
- 360° heating with dual heating sheet and fan
- 4.6 inch LCD touch screen
- Maximum temperature of 70°
- Lists PC among filament types
Cons
- Warranty stated only as '1', with no unit
- 2.76 lb, heavier than the S1 Plus
- Heating speed gain of 30% is a maker claim
- No dimensions in inches stated
Other machines to compare
SUNLU PETG Filament 1.75mmCheck price on Amazon
SUNLU Silk PLA+ Filament 1.75mmCheck price on Amazon
SUNLU PLA+ 2.0 Filament 1.75mmCheck price on Amazon
3D Printer Silk FilamentCheck price on Amazon
SUNLU 4KG Upgrade PLA+2.0 3D Printer Filament BundleCheck price on Amazon
SUNLU Galaxy PLA Filament 1.75mmCheck price on Amazon
Sunlu S1 vs S2 filament dryer side by side
| Spec | SUNLU S1 Plus | SUNLU S2 | |
|---|---|---|---|
| HQ Score | 66 | 61 | |
| Heating | Fan design | 360° dual heating sheet and fan | |
| Max temperature | 35 to 55°C | 70° | |
| Display | 2 inch LCD screen | 4.6 inch LCD touch screen | |
| Capacity | 210*89(H)mm | 210*85(H)mm | |
| Filament sizes | 1.75, 2.85, 3.00 mm | 1.75, 2.85, 3.00 mm | |
| Filament types | PLA, PETG, ABS, TPU, Nylon, PA | PLA, PETG, ABS, TPU, Nylon, PA, PC | |
| Controls | Left and right buttons | One-key set, touch screen | |
| Warranty | 1 Year | 1, no unit stated | |
| Weight | 2.12 lb | 2.76 lb |
Size and performance figures are the brand’s ratings quoted from listings on 5 November 2026.
Heating and temperature
Both dryers use a fan, but the S2 adds a dual heating sheet for 360° all-round heating, and the maker claims it increases heating speed by 30%. The S1 Plus lists a fan design that speeds up the discharge of excess water from filament. On temperature, the S1 Plus lists an adjustable range of 35 to 55°C, while the S2 lists a maximum of 70° with free adjustment to suit the filament and the environment. The S2 listing gives no unit for that 70° figure, so the two maximums are not directly comparable on the listings alone. Neither listing states a fixed drying time.
Display and controls
The S2 has the larger screen: a 4.6 inch LCD touch screen that shows temperature, time, humidity, filament type and countdown time, with one-key set and one-click operation. The S1 Plus has a 2 inch LCD screen that shows temperature, time and humidity, with a left button for dry time and a right button for temperature. Both detect and display temperature and humidity in the box.
Capacity and filament types
Capacity is close: the S1 Plus lists a maximum of 210*89(H)mm and the S2 lists 210*85(H)mm. Both take 1.75, 2.85 and 3.00 mm filament in PLA, PETG, ABS, TPU, Nylon and PA. The S2 adds PC to that list. Both list compatibility with all major 3D printer filament brands.
Support and warranty
Both listings offer after-sales service and technical support. The S1 Plus states a 1 Year warranty in its spec table. The S2 states a warranty of ‘1’ with no unit, so the listing leaves the term unclear. On warranty alone, the S1 Plus is the clearer pick.
Choose the SUNLU S1 Plus if
- You want a 1 Year warranty stated in the listing.
- You dry PLA, PETG, ABS, TPU, Nylon or PA and want a fan dryer with a 2 inch display.
- You prefer buttons over a touch screen.
Choose the SUNLU S2 if
- You dry PC, which only the S2 listing names.
- You want a maximum of 70° and a 4.6 inch touch screen.
- You want 360° heating with a dual heating sheet and fan.
For more dryers, see filament dryer vs dry box.
A filament dryer holds heat inside the box while it runs. Keep it clear of clutter, stay nearby while it dries, and let it cool before you open it. Stay inside the temperature range the listing states: 35 to 55°C on the S1 Plus, and no higher than the 70° maximum on the S2.
Project Match
- PLA, PETG and ABS drying: either dryer, since both list all three.
- TPU, Nylon and PA drying: either dryer, since both list all three.
- PC drying: the S2, since only its listing names PC.
FAQ: lasers and CNC
Which SUNLU dryer is better, the S1 Plus or the S2?
It depends on what you dry. The S2 lists a maximum of 70° (with no unit given), a touch screen and PC among its filament types. The S1 Plus has the clearer warranty, stated as 1 Year, while the S2 states only ‘1’ with no unit. Neither is better for everyone.
What is the maximum temperature of the SUNLU S2?
The S2 listing states a maximum of 70°, with free adjustment to suit the filament and the environment. The S1 Plus lists an adjustable range of 35 to 55°C. Check the listing for the filament you plan to dry.
Can the S1 Plus dry PC filament?
Not per its listing. The S1 Plus names PLA, PETG, ABS, TPU, Nylon and PA, with no PC. The S2 names PC along with the same six types. If you dry PC, the S2 is the pick whose listing states it.
What filament sizes do these dryers take?
Both take 1.75, 2.85 and 3.00 mm filament. Both list a maximum capacity near 210 mm across, with the S1 Plus at 210*89(H)mm and the S2 at 210*85(H)mm. Check the spool size against those figures before you order.
Do these dryers have a warranty?
The S1 Plus states a 1 Year warranty. The S2 states a warranty of ‘1’ with no unit, so the term is unclear from the listing. Both listings offer after-sales service and technical support.
Related: filament dryer vs dry box, Creality Space Pi vs SUNLU S2 filament dryer, PETG vs PC filament and how to choose a laser engraver.




