Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Creality Space Pi vs Sunlu S2 Filament Dryer: Which One Should You Buy?

Two Creality Space Pi dryers and two SUNLU S2 dryers compared on heating, temperature range, timer, screen, capacity and warranty.

Creality Space Pi vs Sunlu S2 Filament Dryer: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 12026 New Official CREALITY Space Pi Filament2026 New Official CREALITY Space Pi Filament9.5/10View on Amazon
  2. 2Creality Space Pi Filament DryerCreality Space Pi Filament Dryer9.5/10View on Amazon
  3. 3SUNLU Official Filament Dryer S2SUNLU Official Filament Dryer S29.5/10View on Amazon
  4. 4SUNLU S2 Filament Dryer, BlackSUNLU S2 Filament Dryer, Black9.5/10View on Amazon

Wet filament prints badly: stringing, clogging and poor adhesion all follow damp spools, and a dryer box warms the filament and drives the moisture out before it reaches the nozzle. This comparison puts the creality space pi vs sunlu s2 filament dryer head to head, using two listings on each side, and compares heating, temperature range, timer, screen, capacity and warranty using what each listing states.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Verdict: pick the Creality Space Pi for a stated 110W PTC heater, 12 presets and a 1 year warranty, or the Space Pi Plus if you dry two spools at once. Pick the SUNLU S2 for the largest stated screen, 4.6 inches on the official listing, or the longest timer, with drying during printing.

Machines on the list

2026 New Official CREALITY Space Pi Filament

2026 New Official CREALITY Space Pi Filament

Creality9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 110W PTC hot-air filament dryer with a fan, a 3.7-inch touch screen, one-key presets for 12 filament types and real-time humidity and temperature monitoring.

Pros

  • 110W PTC heater with 360 degree hot-air circulation and a fan
  • One-key presets for 12 filament types, 45 degrees C to 70 degrees C
  • Real-time humidity and temperature display on a 3.7-inch touch screen
  • 1 Year Manufacture warranty stated in the spec table

Cons

  • No spool capacity stated in the listing
  • No drying timer stated in the listing
  • Filament sizes stated are 1.75 and 2.85 mm only
  • Touch screen is 3.7-inch, smaller than the 4.6-inch SUNLU screen
Creality Space Pi Filament Dryer

Creality Space Pi Filament Dryer

Creality9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2-spool filament dryer with double 360 degree heating, a 4-inch touch screen, a 0 to 48 hour timer and one-touch presets for 12 filament types.

Pros

  • 2-spool capacity, the only two-spool listing here
  • Double 360 degree PTC heating with a fan
  • 0 to 48 hour drying timer with temperature control from 45 degrees C to 70 degrees C
  • One-touch presets for 12 filament types, plus real-time humidity and temperature display

Cons

  • No weight stated in the listing
  • No dimensions stated in the listing
  • No warranty term stated
  • No heater wattage stated, unlike the base Space Pi at 110W
SUNLU Official Filament Dryer S2

SUNLU Official Filament Dryer S2

SUNLU9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A SUNLU S2 filament dryer with 360 degree heating, a dual heating sheet and fan, a 4.6-inch touch screen and a maximum temperature of 70 degrees.

Pros

  • 4.6-inch touch screen, the largest screen here
  • 360 degree heating with a dual heating sheet and fan
  • Maximum temperature of 70 degrees, adjustable to the filament and environment
  • Holds 1.75, 2.85 and 3.00 mm filaments in PLA, PETG, ABS, TPU, Nylon, PA and PC

Cons

  • Warranty description lists only '1' with no unit, so no term is credited
  • No drying timer stated in the listing
  • No spool count stated, only a holder size of 210 by 85 mm
  • 3.3 lb listed weight, heavier than the Creality Space Pi at 3.0 lb
SUNLU S2 Filament Dryer, Black

SUNLU S2 Filament Dryer, Black

SUNLU9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A SUNLU S2 filament dryer with a built-in circulation fan, a 35 degrees C to 70 degrees C range, a 0 to 99 hour timer and a translucent lid for checking the filament.

Pros

  • Drying timer from 0 to 99 hours, the longest timer here
  • Adjustable temperature from 35 degrees C to 70 degrees C
  • Built-in circulation fan with 360 degree hot air and a built-in spindle for even drying
  • Translucent lid lets you check the filament without opening the lid

Cons

  • Warranty description lists only '1' with no unit, so no term is credited
  • No weight stated in the listing
  • No touch screen size stated in the listing
  • No humidity display stated, only temperature and time settings

Other machines to compare

Creality space pi vs sunlu s2 filament dryer side by side

Spec Creality Space Pi Creality Space Pi Plus SUNLU S2 Official SUNLU S2 Black
HQ Score 66 60 58 58
Heating 110W PTC, 360 degree hot air, fan Double 360 degree PTC heating, fan 360 degree heating, dual heating sheet, fan Built-in circulation fan, 360 degree hot air
Temperature 45 degrees C to 70 degrees C 45 degrees C to 70 degrees C (113 degrees F to 158 degrees F) Up to 70 degrees 35 degrees C to 70 degrees C
Timer Not stated 0 to 48 hours Not stated 0 to 99 hours
Touch screen 3.7-inch 4-inch 4.6-inch Large touch screen
Filament presets 12 types, one-key 12 types, one-touch Not stated Not stated
Capacity Not stated 2 spools Holder 210 by 85 mm 265 by 274 by 118 mm
Filament sizes 1.75, 2.85 mm 1.75, 2.85, 3 mm 1.75, 2.85, 3.00 mm 1.75, 2.85, 3.00 mm
Weight 3.0 lb Not stated 3.3 lb Not stated
Warranty 1 year Not stated Not stated Not stated
Humidity display Real-time sensor Real-time display Temperature and humidity detection Not stated

Specs are what each manufacturer publishes as its rating on the listing, collected 5 November 2026.

Heating and drying

Both sides heat with a fan moving hot air 360 degrees around the spool. The Creality Space Pi uses a 110W PTC heater, and the Space Pi Plus uses double 360 degree PTC heating; the SUNLU S2 uses a dual heating sheet and fan, and the maker claims the design increases heating speed by 30 percent. The second SUNLU listing adds a built-in spindle that keeps the filament spinning for even drying. No listing states a drying time for a full spool, so that stays unclear.

Temperature and time

Creality lists 45 degrees C to 70 degrees C on both dryers; the Plus adds 113 degrees F to 158 degrees F. SUNLU lists up to 70 degrees on the official listing and 35 degrees C to 70 degrees C on the second listing, so the second SUNLU listing starts lower. Timers split the same way: the Space Pi Plus runs 0 to 48 hours, the second SUNLU listing runs 0 to 99 hours, and the other two listings state no timer.

Screens and presets

Screens are where the official SUNLU S2 leads: it has a 4.6-inch touch screen, against 4 inches on the Space Pi Plus and 3.7 inches on the Space Pi. The second SUNLU listing states a large touch screen with no size. Presets are where Creality leads: both Creality listings offer one-key or one-touch settings for 12 filament types, while neither SUNLU listing states a preset count. Both sides show temperature and humidity while drying, except the second SUNLU listing.

Capacity and filament sizes

Only the Space Pi Plus states a spool count: 2 spools. The SUNLU listings state holder sizes instead: 210 by 85 mm on the official listing and 265 by 274 by 118 mm on the second listing. All four take 1.75 and 2.85 mm filament; the Plus and both SUNLU listings also take 3.00 mm, while the base Space Pi lists only 1.75 and 2.85 mm.

Choose the Creality Space Pi if

  • You want a stated 110W PTC heater with 12 presets and a 1 year warranty.
  • You dry two spools at once and want the Plus with its 0 to 48 hour timer.
  • You want a real-time humidity and temperature display.

Choose the SUNLU S2 if

  • You want the largest stated screen here, 4.6 inches on the official listing.
  • You want the longest timer, 0 to 99 hours, and drying during printing.
  • You want a translucent lid to check the filament without opening the box.

For a sealed box instead of a heated dryer, see our filament dryer vs dry box guide.

Safety

Filament dryers run hot for hours. Keep the box clear of flammable material, use the temperature range the maker lists for each filament, and keep the dryer where you can check on it while it runs.

Project Match

Project Pick
Drying PLA and PETG Either side; all four listings state PLA and PETG
Drying ABS and ASA Creality Space Pi, the only listing here that states ASA
Drying Nylon and PA Creality Space Pi or the official SUNLU S2; both list Nylon and PA
Two spools at once Creality Space Pi Plus, the only 2-spool listing here
Drying while printing SUNLU S2, which the listing states can dry filament during printing

FAQ: lasers and CNC

What temperature should I dry PLA at?

The listings give a range rather than a per-filament table: Creality runs 45 degrees C to 70 degrees C on both dryers, and the second SUNLU listing runs 35 degrees C to 70 degrees C while the official listing states a maximum of 70 degrees. Use the preset for the filament type where the listing states one, and stay inside the range the maker lists.

Can I dry two spools at once?

Only the Creality Space Pi Plus lists 2-spool capacity. The other three listings state no spool count, so do not assume they hold two.

Do these dryers work while printing?

The second SUNLU S2 listing states it can dry filament during printing, which the maker calls out for printers in humid places such as basements. The Creality listings do not state drying during printing.

What filament sizes do they fit?

All four take 1.75 and 2.85 mm filament. The Space Pi Plus and both SUNLU listings also take 3.00 mm, while the base Space Pi lists only 1.75 and 2.85 mm.

Which dryer has the bigger screen?

The SUNLU S2 official listing has a 4.6-inch touch screen, the largest stated size here. The Space Pi Plus has a 4-inch screen and the base Space Pi a 3.7-inch screen. The second SUNLU listing states a large touch screen with no size.

Related: best filament dryer cabinet, best 3D printer stand and best filament dry box.

More buying guides

3D Printer Accessories ·

Best Spray Paint for Hard Plastic (2026)

Four spray paints for hard plastic, from a plastic-specific trim restorer to a textured automotive topcoat, compared by coverage, dry time and finish.