Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Use Glue Stick on 3D Printer Bed: A Practical Guide

A thin coat of glue stick on a clean 3D printer bed holds the first layer down and washes off with water when the print is done.

How to Use Glue Stick on 3D Printer Bed: A Practical Guide
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Geeetech 3‑Pack 3D Printer Glue Sticks, 36gGeeetech 3‑Pack 3D Printer Glue Sticks, 36g9.6/10View on Amazon
  2. 2ENOMAKER for Bamboo Lab 3D Printer Bed AdhesiveENOMAKER for Bamboo Lab 3D Printer Bed Adhesive9.5/10View on Amazon
  3. 3Elmer's Disappearing Purple School Glue SticksElmer's Disappearing Purple School Glue Sticks9.4/10View on Amazon
  4. 4Amazon Basics Purple Washable School Glue SticksAmazon Basics Purple Washable School Glue Sticks9.3/10View on Amazon

How to use glue stick on 3D printer bed is simple: clean the build plate, spread one thin, even coat over the print area only, then start the print and wash the bed with water when the model comes off. The glue gives the first layer extra grip so corners stay down, and it releases the print more easily once the bed cools.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Geeetech 3‑Pack 3D Printer Glue Sticks, 36g

Geeetech 3‑Pack 3D Printer Glue Sticks, 36g

Geeetech9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-pack of 36g PVP glue sticks made for 3D printer beds, with each stick supporting over 100 printing sessions.

Pros

  • Made for 3D printer beds, with PEI, glass and aluminum plates stated
  • Each 36g stick supports over 100 printing sessions
  • Water-soluble PVP formula rinses off with clean water
  • Covers PLA, ABS, PETG, ASA and TPU filaments

Cons

  • No warranty term in the listing
  • Clear formula gives no purple guide while spreading
  • Only 3 sticks in the pack
  • No stated support for PET filament
ENOMAKER for Bamboo Lab 3D Printer Bed Adhesive

ENOMAKER for Bamboo Lab 3D Printer Bed Adhesive

ENOMAKER9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 60ml liquid bed adhesive with a press applicator, made for Bambu Lab printers and a wide range of build plates.

Pros

  • Liquid form spreads more evenly than a solid stick, per the maker
  • Made for Bambu Lab printers and high-speed printing
  • Wide plate list: glass, PEI, PEO, PET, Buildtak and aluminum
  • Water-soluble and odorless formula

Cons

  • Maker recommends reapplying before each printing session
  • No warranty term in the listing
  • Liquid form needs the applicator valve to dispense
  • No pack count stated, one 60ml bottle
Elmer's Disappearing Purple School Glue Sticks

Elmer's Disappearing Purple School Glue Sticks

Elmer's9.4/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 30-count box of 7g purple glue sticks that dry clear, with a stated 2 Years warranty.

Pros

  • Goes on purple so the coat is easy to see, then dries clear
  • 30-count box of 7g sticks
  • Washable, acid-free, non-toxic formula
  • Stated 2 Years warranty

Cons

  • Sold as a school and craft glue, with no 3D printer bed claim
  • No build-plate compatibility stated
  • Small 7g sticks for coating a large build plate
  • No filament compatibility stated
Amazon Basics Purple Washable School Glue Sticks

Amazon Basics Purple Washable School Glue Sticks

Amazon Basics9.3/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-pack of 0.21 oz purple glue sticks that dry clear and wash off hands and clothes.

Pros

  • Purple formula shows coverage and dries clear
  • Washable from hands and clothes
  • Smooth stick dispenses evenly with no dripping
  • Bonds paper, photos and fabric for craft use

Cons

  • Sold as a school glue, with no 3D printer bed claim
  • No warranty term in the listing
  • Only 4 sticks in the pack
  • No build-plate compatibility stated

How to Use Glue Stick on 3D Printer Bed

Start with a clean, dry build plate. Any dust or old adhesive under the new coat makes the grip uneven, so wipe the plate and let it dry before you spread anything.

  1. Coat only the print area. Spread a thin coat over the zone where the model will sit, not the whole plate. Geeetech states this directly: coat the active printing zone instead of fully covering the build plate.
  2. Keep the coat thin and even. A thick coat leaves ridges under the first layer, so one smooth pass lays the thin coat the maker asks for.
  3. Watch the color. Purple sticks go on purple and dry clear, which shows where the coat already sits. A clear stick gives no color guide, so work in even rows and check the sheen.
  4. Print as normal. The first layer grips the film while the rest of the print builds on top of it.
  5. Release and wash. After the print cools, lift the model off the plate, then rinse the bed with clean water or wipe it with a wet rag. The purpose-built picks state water-soluble formulas, and the school sticks are washable, so the residue comes off with water.

For a liquid adhesive, press the applicator head to open the valve and spread the liquid evenly. ENOMAKER recommends reapplying before each printing session.

Which Surfaces and Filaments It Suits

Glue sticks made for 3D printing state their surfaces plainly. Geeetech lists PEI sheets, carbon-crystal glass beds, aluminum glass plates and other common build plates, with PLA, ABS, PETG, ASA and TPU filaments. ENOMAKER lists low-temperature and high-temperature plates, textured and smooth build plates, glass, PEI, PEO, PET, Buildtak and aluminum plates, with PLA, PETG, PET, ABS, ASA and TPU.

School glue sticks state no build-plate compatibility. They are washable, non-toxic craft glues that dry clear, but with no stated bed match, a purpose-built stick that states the PEI or glass match is the surer pick for a first attempt. Readers who keep fighting lifted corners may also want our guide to 3D printer adhesion problems.

The Gear for This Job

The four picks below cover the job from both ends: purpose-built bed adhesives that state plate and filament compatibility, and plain school glue sticks that dry clear and wash off with water.

Mistakes That Waste Glue and Prints

  • Coating the whole plate when only the print area needs glue.
  • Laying the coat on thick. A thick coat leaves ridges under the first layer and wastes the stick.
  • Skipping the wash between prints. Old residue builds up and the next coat grips unevenly.
  • Using a stick with no stated plate match. Check the listing for PEI or glass before you buy.

FAQ: lasers and CNC

Does a glue stick work on a PEI build plate?

Yes, when the listing states it. Geeetech lists PEI sheets, and ENOMAKER lists PEI alongside glass, Buildtak and aluminum plates. A school glue stick states no PEI compatibility, so a purpose-built stick is the safer pick.

Can I use a school glue stick on a 3D printer bed?

A school glue stick is a washable stick that goes on purple and dries clear, and it washes off with water, but it states no build-plate compatibility. Purpose-built sticks state PEI, glass and filament matches, so use a school stick where no stated match is needed and a purpose-built one when the plate or filament matters.

How do I clean glue off a 3D printer bed?

Rinse the bed with clean water after the print, or wipe it with a wet rag. Both purpose-built picks state water-soluble formulas, and the school sticks are washable, so water handles the cleanup.

How often should I reapply glue stick?

ENOMAKER recommends reapplying before each printing session. A Geeetech stick supports over 100 printing sessions, which refers to the life of the stick, not one coat, and Geeetech states no reapply rule of its own.

Which filaments work with glue stick on the bed?

Geeetech states PLA, ABS, PETG, ASA and TPU, and ENOMAKER adds PET to that list. Match the filament to the stick’s stated list before printing, and check the plate list at the same time.

Related: the 3D printers hub, how to 3D print for beginners and how to improve 3D print quality.

More buying guides