Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Do I Need to Use Glue Stick for 3D Printing?

A glue stick is not needed for every print, but a thin coat of adhesive helps first layers grip the bed and stops edges lifting while the print builds.

Do I Need to Use Glue Stick for 3D Printing?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Geeetech 6‑Pack 3D Printer Glue Sticks, 36gGeeetech 6‑Pack 3D Printer Glue Sticks, 36g9.6/10View on Amazon
  2. 2Creality 3D Printer Glue Sticks for Hot BedCreality 3D Printer Glue Sticks for Hot Bed9.6/10View on Amazon
  3. 3TEQStone 3D Printer Glue Stick 3 PackTEQStone 3D Printer Glue Stick 3 Pack9.5/10View on Amazon
  4. 43DTOOLS Bambu lab Original 3D Printer Build Plate3DTOOLS Bambu lab Original 3D Printer Build Plate9.5/10View on Amazon

Do I need to use glue stick for 3D printing? Not for every print, but a glue stick earns its place when a first layer will not stay put. A thin coat of adhesive gives the first layer something to grip, holds the edges down while the print builds, and lets the print release once the bed cools. The sticks in this guide do that job on the beds their makers list.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Geeetech 6‑Pack 3D Printer Glue Sticks, 36g

Geeetech 6‑Pack 3D Printer Glue Sticks, 36g

Geeetech9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 6-pack of 36g PVP sticks for PEI and glass beds, each rated for over 100 sessions.

Pros

  • 6-pack of 36g sticks, the largest pack in this guide
  • Each 36g stick supports over 100 printing sessions
  • Covers PLA, ABS, PETG, ASA and TPU on PEI and glass beds
  • Non-toxic, low-odor PVP formula that rinses off with clean water

Cons

  • No warranty term is stated
  • PC and PA filaments are not listed, so those prints need another adhesive
  • Only the active zone needs a coat, so full-bed coverage wastes the stick
  • A 6-pack suits a frequent printer, not an occasional one
Creality 3D Printer Glue Sticks for Hot Bed

Creality 3D Printer Glue Sticks for Hot Bed

Creality9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A PVP glue stick pack for hot beds, covering PLA, ABS, PETG, PC, PA and TPU on glass, PEI, PEO and textured plates.

Pros

  • Covers PLA, ABS, PETG, PC, PA and TPU
  • Formaldehyde-free PVP formula with no harsh chemicals or unpleasant odors
  • Works on glass, PEI, PEO, textured plates and low-temp plates
  • Water-washable with no sticky residue left behind

Cons

  • No warranty term is stated
  • The 2-pack is the smallest multi-pack here
  • No per-stick print count is stated
  • A thin, even coat is needed, so a heavy hand wastes the stick
TEQStone 3D Printer Glue Stick 3 Pack

TEQStone 3D Printer Glue Stick 3 Pack

TEQStone9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-pack of 36g sticks, each good for more than 100 prints, for textured and smooth PEI, glass, aluminum and flexible plates.

Pros

  • 3-pack of 36g sticks, each good for more than 100 prints
  • At least 300 prints from one purchase, per the maker
  • Works on textured and smooth PEI, glass, aluminum and flexible plates
  • PVP formula with no unpleasant odors, and cleanup with a damp cloth or a rinse

Cons

  • Covers ABS, PLA and PETG only; PC, PA, ASA and TPU are not listed
  • Only a 3-pack is offered, with no single stick to try first
  • A daily printer will go through the 3-pack faster than the 6-pack
  • Cleanup needs a damp cloth or a rinse after each print
3DTOOLS Bambu lab Original 3D Printer Build Plate

3DTOOLS Bambu lab Original 3D Printer Build Plate

3DTOOLS9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single solid glue stick made for Bambu Lab A1 Mini, P1 and X1 printers, covering PLA, ABS, PETG, PC, PA and TPU.

Pros

  • Made for Bambu Lab A1 Mini, P1 and X1 printers
  • Covers PLA, ABS, PETG, PC, PA and TPU filaments
  • Single stick, so a Bambu Lab owner can try it first
  • Solid stick format for the hot bed

Cons

  • Only 1 stick in the pack, the least here
  • No build-plate types are named
  • Choking hazard warning: keep small parts away from children under 3 years old
  • Made for Bambu Lab printers, so other brands have no stated fit

Do I need to use glue stick for 3D printing?

A glue stick helps most when the first layer lifts or curls at the edges, or when a print shifts partway through. The Creality, TEQStone and Geeetech makers describe the same job: stronger first-layer adhesion, less warping, and easy release after cooling. A smooth glass bed and a textured PEI bed both take a glue coat.

When prints already stick well and release cleanly, a glue stick adds a step and a cleanup for no gain. Reach for it when edges lift, corners curl, or a print comes loose. See our 3D printer adhesion problems page for the other causes of a failed first layer.

How to use a glue stick on a print bed

Spread a thin, even coat. The Geeetech maker says to coat only the active printing zone and leave the rest of the bed bare, which avoids waste. Run the print as usual and let the bed cool before removing the finished piece, since prints release easily after cooling.

Cleanup is the easy part: the Creality, TEQStone and Geeetech sticks are water-soluble or water-washable, so wipe the bed with a damp cloth or rinse it with clean water.

Glue sticks for 3D printing beds

The four sticks below all handle first-layer adhesion and differ in pack size, filament range and the beds they list, so pick the one that matches the filaments and plates on the bench.

FAQ: lasers and CNC

Do I need a glue stick for 3D printing on a PEI bed?

Not always, but TEQStone lists its stick for both textured and smooth PEI, and Creality and Geeetech list PEI as well, and it helps when a first layer lifts or a print releases too hard from the plate.

Does a glue stick work with PLA, ABS and PETG?

Yes, every stick here lists PLA, ABS and PETG, and the Creality and 3DTOOLS sticks (on Amazon) also list PC, PA and TPU, while the Geeetech stick adds ASA. Check the filament list before buying.

How do I clean glue stick off a 3D printer bed?

Wipe the bed with a damp cloth or rinse it with clean water. The Creality, TEQStone and Geeetech sticks use a water-soluble or water-washable PVP formula, so the residue comes off with no solvents and no scraping. The 3DTOOLS stick states no cleanup method.

Does a glue stick stop warping?

It helps: the Creality maker describes stronger bed adhesion at high temperatures that keeps model edges from lifting or curling, and TEQStone describes stronger adhesion that reduces warping. It is one part of first-layer adhesion, not a fix for every failed print.

Related: the 3D printer hub and how to 3D print for beginners.

More buying guides