Heat Press Maintenance: Cleaning and Care Tips
A practical guide to heat press maintenance: clean the platen, shield it with Teflon sheets, mats and covers, and keep every transfer crisp.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Upgraded Silicone Heat Press Mat,18"x22"x1/329.6/10View on Amazon - 2
Heat Press Platen Covers for 15x15 Auto Heat9.6/10View on Amazon - 3
Silicone Heat Press Mat 15x12 Inch9.6/10View on Amazon - 4
XEUZK Sublimation Shirts Tool Kits With 8 T Shirt9.5/10View on Amazon
Heat press maintenance is the routine that keeps a press printing clean transfers instead of ghosting old ink onto the next shirt. A press that runs daily collects ink, adhesive and transfer residue on its platen, and that buildup shows up as marks on fresh work. This guide walks through the cleaning and care steps in order, then shows the sheets, mats and covers that protect the platen.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Check the stated sizes against your press before ordering.

Upgraded Silicone Heat Press Mat,18"x22"x1/32
A reusable 18 x 22 in foam cover pad, 1/32 in thick, for even pressure over seams, buttons and zippers.
Pros
- 18 x 22 in size covers 15 x 15 and 12 x 10 in presses
- 1/32 in pad suits sublimation, HTV, emblems and patches
- Even pressure across seams, zippers and buttons
- Reusable pad shields garments from burns
Cons
- No maximum temperature is stated
- 18 x 22 in size overhangs smaller presses
- Grey is the only color stated
- One pad in the box; no spare is included

Heat Press Platen Covers for 15x15 Auto Heat
A 2-pack of Teflon-coated platen covers for 15 x 15 in HTVRONT auto heat presses, rated to 500°F (260°C).
Pros
- 2-pack covers the upper and lower platen
- Teflon-coated fiberglass releases material after pressing
- Rated to 500°F (260°C) for HTV, sublimation and DTF
- Elastic edge fits on and off fast
Cons
- Fits only 3 HTVRONT models
- 15 x 15 in size only
- Covers only; no sheets, tape or tools
- Wiping after use is part of the routine

Silicone Heat Press Mat 15x12 Inch
A washable 15 x 12 in silicone heat press mat rated to 572°F (300°C) for vinyl, HTV and sublimation pressing.
Pros
- Rated to 572°F (300°C) for high-heat pressing
- 15 x 12 in size fits manual and semi-auto presses
- Washable: rinse dirt off under water
- Non-slip grip holds fabric in place
Cons
- 6-month warranty is shorter than the 1-year terms here
- 15 x 12 in size does not cover larger platens
- Rinsing after messy jobs adds a cleaning step
- Red is the only color stated

XEUZK Sublimation Shirts Tool Kits With 8 T Shirt
A sublimation kit with 12 x 16 in Teflon sheets, heat-resistant gloves, tape and layout tools.
Pros
- 3-pack of 12 x 16 in Teflon sheets shields the press
- Heat-resistant gloves with silicone bumps
- 2 rolls of heat-resistant tape, 16 m long
- 8 rulers, 50 pins, tape rule and scraper for layout
Cons
- No warranty term is stated
- 12 x 16 in sheets leave larger platens partly uncovered
- No silicone mat or platen cover is included
- The kit mixes press supplies with general craft tools
What heat press maintenance covers
Heat press maintenance has three parts: cleaning the platen, protecting it while you press, and checking the parts that wear. Cleaning takes ink and adhesive off the platens so residue never reaches the next blank. Protection means a sheet, mat or cover between the press and the work. Checking means looking at covers and mats for wear.
Clean the platen after every session
Wipe the upper and lower platens after each session, before residue hardens. A damp cloth takes off most ink and adhesive, and the ruclles covers (on Amazon) wipe clean the same way. Let the press cool before you clean.
Protect the platen while you press
A Teflon sheet, a silicone mat or a platen cover sits between the press and the blank, so ink and adhesive land on the protector instead of the platen. The XEUZK kit brings three 12 x 16 in Teflon sheets for sublimation, and the LGIB silicone mat spreads heat evenly and rinses clean under water. The ruclles covers guard the platens of three HTVRONT models, and the HAWERSI pad (on Amazon) spreads pressure evenly over seams, buttons and zippers. Pick the protector that matches your press size and material. The parts of a heat press guide shows where each piece sits.
The gear for heat press maintenance
The four supplies below handle the steps above: sheets and a mat shield the platen, covers guard an HTVRONT auto press, and a foam pad evens out pressure over seams.
FAQ: lasers and CNC
How often should I clean a heat press platen?
Wipe the platen after every session, before residue hardens. A damp cloth takes off most ink and adhesive, and the covers here wipe clean the same way.
What does a Teflon sheet do on a heat press?
It acts as a protective barrier between the blank and the press, so ink does not transfer onto the platen during sublimation. The XEUZK kit includes three 12 x 16 in Teflon sheets for that job.
Can I wash a silicone heat press mat?
The LGIB mat rinses clean under water, with no stains or odors left behind. Let it dry before the next session.
Do platen covers fit every heat press?
No. The ruclles covers fit only three HTVRONT models: the Auto Heat Press, the Auto Heat Press 2 and the Heat Press. Check your machine model before ordering.
How hot can these mats and covers go?
The LGIB silicone mat is rated to 572°F (300°C), the ruclles covers to 500°F (260°C), and the HAWERSI pad states no maximum temperature. Match the rating to the temperature your press runs at.
Related: the craft machines hub, best heat press for home use, sublimation printer maintenance and temperature guide for heat press.




