Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Diamond Bit Drill Tips for Clean Holes

Diamond bit drill tips for clean holes in tile, glass and stone: start at an angle, keep the bit cool, use rotary mode only and match the bit to the hole.

Diamond Bit Drill Tips for Clean Holes
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Sworker Diamond Drill Bits 1mm 1.5mm 2mm 2.5mm 5Sworker Diamond Drill Bits 1mm 1.5mm 2mm 2.5mm 59.7/10View on Amazon
  2. 210pc Dry Diamond Core Drill Bits Set10pc Dry Diamond Core Drill Bits Set9.7/10View on Amazon
  3. 3DYRECELVE Dry Diamond Drill Bits for CeramicDYRECELVE Dry Diamond Drill Bits for Ceramic9.6/10View on Amazon
  4. 415 Pcs Diamond Drill Bits, Hole Saw Kit for Glass15 Pcs Diamond Drill Bits, Hole Saw Kit for Glass9.6/10View on Amazon

Diamond bit drill tips come down to a slow start, a steady hand and cooling. Start the bit at an angle so it bites, bring it upright once the cut opens, keep the surface wet or let a wax-cooled bit rest between holes, and drill in rotary mode with gentle pressure. The sections below walk through each step, with the gear that fits each job.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

Diamond bits do not drill tempered glass, and the YLYL set states this plainly. Confirm the glass type before starting. Use rotary mode only and keep impact mode off.

Sworker Diamond Drill Bits 1mm 1.5mm 2mm 2.5mm 5

Sworker Diamond Drill Bits 1mm 1.5mm 2mm 2.5mm 5

Sworker9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 20-piece set of 1 to 2.5 mm diamond twist bits with 4 collets for Dremel rotary tools.

Pros

  • 20 bits in 1 to 2.5 mm sizes for small holes
  • 4 brass collets for Dremel and similar rotary tools
  • 120-grit diamond coating for smooth, precise holes
  • 5-Year Returnless Replacement stated

Cons

  • Sizes stop at 2.5 mm, too small for tile fixtures
  • Needs water cooling for thick glass and stone
  • Made for rotary tools, not full-size drills
  • No storage case is named
10pc Dry Diamond Core Drill Bits Set

10pc Dry Diamond Core Drill Bits Set

DKIBBITH9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 10-piece set of dry diamond core bits from 3/16 to 5/8 inch, with wax lubricant, side flutes and depth marks.

Pros

  • Sizes from 3/16 to 5/8 inch in one set
  • Integrated wax lubricant cools the bit for dry drilling
  • Side flutes clear debris, depth marks guide hole depth
  • Round shank fits most popular electric drills

Cons

  • No warranty term is stated
  • Made for dry drilling, with a pause after each hole
  • No fitted case is stated
  • No carbide starter bit is included
DYRECELVE Dry Diamond Drill Bits for Ceramic

DYRECELVE Dry Diamond Drill Bits for Ceramic

DYRECELVE9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 10-piece set with 8 vacuum-brazed diamond core bits and 2 carbide-tipped hex starters.

Pros

  • Two carbide-tipped hex bits mark a shallow guide first
  • Eight vacuum-brazed diamond core bits for tile and stone
  • Built-in cooling wax supports dry rotary drilling
  • Fitted case keeps all 10 bits grouped

Cons

  • Largest core bit is 1/2 inch, smaller than the DKIBBITH set
  • No warranty term is stated
  • No 9/16 or 5/8 inch size in the set
  • No depth marks are stated
15 Pcs Diamond Drill Bits, Hole Saw Kit for Glass

15 Pcs Diamond Drill Bits, Hole Saw Kit for Glass

YLYL9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 15-piece hole saw kit from 6 to 50 mm for glass, ceramic and tile, water cooled with nickel-plated steel bodies.

Pros

  • 15 sizes from 6 to 50 mm, the widest range here
  • Side slots feed cooling water in and clear chips
  • Nickel-plated carbon steel bodies resist corrosion
  • Straight shank fits standard 3/8 in drill chucks

Cons

  • Needs water while drilling, not a dry set
  • Not for wood, metal, concrete or tempered glass
  • Low-speed use only, per the listing
  • No case is stated

Diamond bit drill tips: start at an angle

The 45-degree start is the first move in the DYRECELVE, DKIBBITH and YLYL sets. The DYRECELVE set says to mark a shallow guide with a carbide-tipped hex bit, then place the diamond core bit at 45 degrees and bring it upright. The DKIBBITH set gives the same start: begin at about 45 degrees, slowly bring the drill upright and move in a circular motion.

Keep the bit cool

Heat dulls diamond grit, so cooling is part of the cut. The DYRECELVE and DKIBBITH sets carry wax inside the bit that cools it during dry drilling; pause between holes and let the bit cool after each hole. The YLYL set works wet instead: keep the surface wet while drilling. The Sworker set says the same for thick glass and stone: submerge the piece in water.

Rotary mode only, gentle pressure

The DYRECELVE set states rotary mode only, and the other sets are also made for rotary drills and rotary tools. The DYRECELVE set says to use rotary mode only, keep impact mode off, apply gentle pressure and clear debris periodically. The DKIBBITH set goes further: do not apply pressure, let the drill bit do the work. Pressure does not speed the cut. For shank sizes and chuck fit, see the drill bit shank types guide.

Match the bit to the material and the hole

Size and material decide the set. The YLYL set spans 6 to 50 mm for wide pot, bottle and countertop holes. The DKIBBITH set covers 3/16 to 5/8 inch for tile fixtures and planter drainage, and the DYRECELVE set covers 3/16 to 1/2 inch with a hex starter. The Sworker set covers 1 to 2.5 mm for pendants and small jewelry holes. All four cut ceramic and porcelain, and the tile sets also list granite, marble and stone. None of them is for tempered glass, and the YLYL set also rules out wood, metal and concrete. For more tile sets, see the best diamond tip drill bit set picks and the best drill bit for tiles picks.

Diamond drill bit sets for these tips

The sets below cover each step in the guide: the tile sets handle fixture and planter holes, the wide set handles pots and bottles, and the small-bit set handles jewelry and sea glass.

FAQ: lasers and CNC

Do diamond drill bits need water?

It depends on the set. The YLYL set needs the surface wet while drilling, and the Sworker set needs water for thick glass and stone. The DYRECELVE and DKIBBITH sets carry wax inside the bit for dry drilling.

What angle do you start a diamond drill bit at?

Start at 45 degrees so the rim bites a small crescent, then bring the bit upright once the cut opens. The DYRECELVE and DKIBBITH sets both give this start.

Can you use a diamond drill bit on tempered glass?

No. Tempered glass shatters under a drill, and the YLYL set states that it is not for tempered glass. Use diamond bits on non-tempered glass only.

Can you use impact mode with a diamond drill bit?

No. The DYRECELVE set says to use rotary mode only and keep impact mode off.

Related: the CNC tooling hub, best diamond tip drill bit set, best drill bit for tiles and diamond vs carbide burrs.

More buying guides