Best 3D Printer Bed Adhesive (2026): 5 Picks for First-Layer Grip
Five bed adhesives for PLA, PETG, ABS and TPU prints, compared by form, size, filaments, surfaces and safety.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallMagigoo 50mL9.6/10View on Amazon - 2
Best Liquid AdhesiveCreality Liquid 80mL9.6/10View on Amazon - 3
Best Large BottleLAYERNEER Bed Weld9.6/10View on Amazon - 4
Best Glue StickCreality Glue Stick9.5/10View on Amazon
A fresh print starts to lift at the corners, the first layer curls away from the plate, and the hours of printing behind it are at risk. The best 3d printer bed adhesive is the glue that holds that first layer down, so the print stays put until it cools and releases cleanly. This guide compares five bed adhesives for PLA, PETG, ABS and TPU prints, by form, size, filaments, surfaces and safety, using only what each listing states.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall Magigoo 50mL: 50mL adhesive for ABS, PLA, PETG, HIPS and TPU, with over 100 prints per bottle. Check price on Amazon
- Best Liquid Adhesive Creality Liquid 80mL: 80ml liquid adhesive with a press-to-open applicator for PLA, PETG, ABS and TPU. Check price on Amazon
- Best Large Bottle LAYERNEER Bed Weld: 118ml bottle with a foam tip applicator, for PLA, ABS, PETG, ASA and CPE. Check price on Amazon
- Best Glue Stick Creality Glue Stick: PVP solid glue stick with no formaldehyde, water washable with no residue. Check price on Amazon
Machines on the list

Magigoo All-in-One 3D Printer Bed Adhesive Glue
A 50mL bed adhesive glue for ABS, PLA, PETG, HIPS and TPU, on glass, PEI, Buildtak and Kapton, delivering over 100 prints.
Pros
- Over 100 prints per bottle, per the listing
- Works with ABS, PLA, PETG, HIPS and TPU filaments
- Works on glass, PEI, Buildtak, Kapton and more
- Odorless and non-flammable, per the listing
Cons
- Warranty description names Manufacturer Warranty with no term
- No applicator tip described beyond shake, press and apply
- 50mL is the smallest liquid size here
- No ASA or CPE filament named

Creality 3D Printer Bed Adhesive 80ml
An 80ml liquid bed adhesive with a press-to-open applicator, for PLA, PETG, ABS and TPU on glass, PEI, PEO, BuildTak and aluminum.
Pros
- Press-to-open applicator for smooth, uniform spreading
- Strong grip for PLA, PETG, ABS, ASA and TPU
- Water-soluble with no sticky residue left behind
- Odorless, non-toxic, and safe for home or workshop use, per the maker
Cons
- No warranty term stated
- Reapply before each print, per the listing
- No print count beyond dozens of prints per bottle

3D Printer Adhesive Glue Bed Weld Original
A 118ml bed adhesive with a built-in foam tip applicator, for PLA, ABS, PETG, ASA and CPE, that prints several times on one coating.
Pros
- 118ml bottle, the largest size here
- Built-in foam tip applicator that will not spill
- Prints several times on a single coating, recharged with a wet sponge
- Low odor and water soluble, with quick drying
Cons
- No surfaces named; the listing asks buyers to check its compatibility image
- No warranty term stated
- No print count beyond several times per coating
- No HIPS, PC, PA or TPU filament named

Original Bamboo Lab All-in-One 3D Printer Adhesive
A 60ml liquid bed adhesive for PLA, ABS, PETG, PET, ASA and TPU, on glass, PEI, PEO, PET, Buildtak and aluminum.
Pros
- Works with PLA, ABS, PETG, PET, ASA and TPU filaments
- Adheres to glass, PEI, PEO, PET, Buildtak and aluminum
- Liquid adhesive that applies evenly and cleans easily
- Environmentally friendly with a lower odor than other glues, per the listing
Cons
- No warranty term stated
- Not recommended to apply multiple coats of glue
- No print count stated in the listing
- 60ml is smaller than the 80ml and 118ml picks

Creality 3D Printer Glue Sticks for Hot Bed
A PVP solid glue stick for PLA, ABS, PETG, PC, PA and TPU, water washable with no residue and no formaldehyde added.
Pros
- PVP solid stick for thin coatings and precise prints
- Works with PLA, ABS, PETG, PC, PA and TPU
- Water washable with no residue left behind
- No formaldehyde added, per the listing
Cons
- No warranty term stated
- No size or volume stated in the listing
- No surfaces named in the listing
- No print count stated in the listing
Other machines to compare
LANDU 3D Printing AdhesiveCheck price on Amazon
for Bambu Lab 3D Printer Adhesive Glue 60MLCheck price on Amazon
Anycubic 2 Pcs 60ml 3D Printer Bed Adhesive GlueCheck price on Amazon
Gizmo Dorks 468MP Double Sided Adhesive Transfer Tape Roll 12Check price on Amazon
AJOYIB Flexible Steel Build Plate with Adhesive Double SideCheck price on Amazon
Specs compared
| Model | HQ Score | Form | Size | Filaments | Surfaces | Safety | Warranty |
|---|---|---|---|---|---|---|---|
| Magigoo 50mL | 9.6/10 | Glue stick | 50mL | ABS, PLA, PETG, HIPS, TPU | Glass, PEI, Buildtak, Kapton | Odorless, non-flammable | Not stated |
| Creality Liquid 80mL | 9.6/10 | Liquid | 80ml | PLA, PETG, ABS, ASA, TPU | Glass, PEI, PEO, BuildTak, aluminum | Odorless, non-toxic | Not stated |
| LAYERNEER Bed Weld | 9.6/10 | Liquid coating | 118ml, 4 fl oz | PLA, ABS, PETG, ASA, CPE | Not stated | Low odor, water soluble | Not stated |
| UniTak3D 60mL | 9.5/10 | Liquid | 60ml | PLA, ABS, PETG, PET, ASA, TPU | Glass, PEI, PEO, PET, Buildtak, aluminum | Lower odor | Not stated |
| Creality Glue Stick | 9.5/10 | Solid glue stick | Not stated | PLA, ABS, PETG, PC, PA, TPU | Not stated | No formaldehyde | Not stated |
These numbers come straight from each maker’s listing and are rated, not measured by us (3 November 2026).
Best 3D Printer Bed Adhesive: What to Check First
Liquid or stick
Three picks here are liquids and two are sticks. The Creality liquid uses a press-to-open applicator for smooth, uniform spreading, the UniTak3D liquid applies evenly and cleans easily, and the LAYERNEER coating uses a built-in foam tip that will not spill. The Creality glue stick is a PVP solid for thin coatings, and the Magigoo stick applies with a shake, press and apply motion. Liquids spread evenly across the plate, while sticks suit a quick coat on a small area.
Filaments and surfaces
Filament coverage runs from PLA, PETG, ABS and TPU on the Creality liquid to ABS, PLA, PETG, HIPS and TPU on the Magigoo, with the UniTak3D adding PET and ASA and the LAYERNEER adding ASA and CPE. Surface coverage runs from glass, PEI, PEO, textured and smooth plates, BuildTak and aluminum on the Creality liquid to glass, PEI, Buildtak and Kapton on the Magigoo. The LAYERNEER listing names no surfaces and asks buyers to check its compatibility image, and the Creality glue stick names no surfaces either.
Release and cleanup
Release after cooling is the other half of the job. The Creality liquid releases models effortlessly after the print cools down, the Magigoo releases prints once cooled, and the LAYERNEER parts typically detach fully without tools once the bed cools to room temperature. Cleanup is water-based across the picks: the Creality liquid rinses with water or wipes with a wet cloth, the Magigoo cleans up with water, and the LAYERNEER coating removes with water. The LAYERNEER coating prints several times on a single application and recharges with a wet sponge.
Safety and odor
Odor and fumes matter in a home workshop. The Creality liquid is odorless and non-toxic, the Magigoo is odorless and non-flammable, the UniTak3D is environmentally friendly with a lower odor than other glues, and the LAYERNEER has a low odor with no harsh smells. The Creality glue stick is made from PVP material with no formaldehyde added. All five picks are water-soluble or water washable, so cleanup needs water rather than solvents.
Project Match
- PLA, PETG, ABS and TPU on glass or PEI: the Creality liquid, whose listing names those filaments and surfaces.
- ABS and HIPS prints: the Magigoo, whose listing names ABS, PLA, PETG, HIPS and TPU.
- Several prints from one coating: the LAYERNEER Bed Weld, whose listing says to print several times on a single coating and recharge with a wet sponge.
- Bambu Lab printers: the UniTak3D, whose listing names Bambu Lab A1, A1 Mini, P1 and X1 printers.
- A solid stick for thin coatings: the Creality glue stick, whose listing describes smooth application for thin coatings.
How the scores add up
Each pick is scored on performance, build, value, safety and warranty. How we pick explains the weights. A spec the listing does not publish scores nothing.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Magigoo 50mL | 9.6 | 30 | 21 | 21 | 8 | 0 |
| Creality Liquid 80mL | 9.6 | 32 | 21 | 20 | 7 | 0 |
| LAYERNEER Bed Weld | 9.6 | 29 | 20 | 20 | 7 | 0 |
| UniTak3D 60mL | 9.5 | 28 | 20 | 20 | 7 | 0 |
| Creality Glue Stick | 9.5 | 27 | 20 | 19 | 7 | 0 |
Scores never fall under 9.2 or rise above 9.8. A machine’s spot between those limits is set purely by its point total.
FAQ: lasers and CNC
How do I use bed adhesive?
Apply it to the active printing area before the print starts. The Magigoo applies with a shake, press and apply motion, the Creality liquid uses a press-to-open applicator, and the LAYERNEER uses a built-in foam tip. The Creality liquid advises reapplying before each print, and the UniTak3D listing says not to apply multiple coats of glue.
How do I clean bed adhesive off the build plate?
All five picks clean with water. The Creality liquid rinses with water or wipes with a wet cloth, the Magigoo cleans up with water, and the LAYERNEER coating removes with water. The Creality glue stick is water washable and leaves no residue behind.
Will bed adhesive work on my build plate?
Check the surfaces each listing names. The Creality liquid names glass, PEI, PEO, textured and smooth plates, BuildTak and aluminum, and the Magigoo names glass, PEI, Buildtak and Kapton. The LAYERNEER listing names no surfaces and asks buyers to check its compatibility image, and the Creality glue stick names no surfaces either.
Which bed adhesives here state a warranty?
None states a concrete warranty term. The Magigoo listing gives a warranty description of Manufacturer Warranty with no term, and the other four listings state no warranty term at all.
How many prints does one bottle last?
The Magigoo delivers over 100 prints, per the listing, and the Creality liquid supports dozens of prints from one bottle, per the listing. The LAYERNEER coating prints several times on a single application and recharges with a wet sponge. The UniTak3D and the Creality glue stick state no print count.
Related: best heat gun for 3D printing, best adhesive for PLA filament, 3D printer maintenance and the 3D printer accessories hub.




