Best Red Abs Filament (2026): 5 Picks for FDM Printers
Five 1.75mm red ABS spools for FDM printers, compared on print temperatures, diameter tolerance, spool size and the warranty each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Most Complete SettingsPolymaker ABS Red9.7/10View on Amazon - 2
Only Stated WarrantyCreality CR-ABS Red9.5/10View on Amazon - 3
Four Spools, Smallest ToleranceSUNLU ABS 4-Pack9.5/10View on Amazon - 4
Vacuum Sealed Red SpoolELEGOO ABS Red 1KG9.5/10View on Amazon
A functional part in red needs more than the right color: it needs to hold its shape when the part gets warm and stay intact when it gets knocked around. That is the job ABS does in a print, and the best red abs filament is the spool that prints cleanly on an enclosed machine and leaves you with a part you can actually use. This guide compares the red ABS spools below on what each listing states: print temperatures, diameter tolerance, spool size and the warranty each maker puts in writing.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Most Complete Settings Polymaker ABS Red: Vicat 104°C, nozzle 245-265°C, bed 90-100°C, fan off, +/- 0.03mm tolerance and drying guidance, the fullest stated profile here. Check price on Amazon
- Only Stated Warranty Creality CR-ABS Red: A stated 1 Year warranty with 12-month and 24 hours after-sales service, plus an odorless, non-toxic claim. Check price on Amazon
- Four Spools, Smallest Tolerance SUNLU ABS 4-Pack: Four 1KG spools with a stated ±0.02mm tolerance and full print settings, though only one spool is red. Check price on Amazon
- Vacuum Sealed Red Spool ELEGOO ABS Red 1KG: A 1.75mm red spool with heat resistance up to 85°C, vacuum sealed, for enclosed printers. Check price on Amazon
Machines on the list

Polymaker ABS Filament Red 1KG 1.75mm
A 1.75mm red ABS spool with the fullest stated print settings here: a Vicat softening temperature of 104°C, nozzle 245-265°C, bed 90-100°C, and a stated tolerance of +/- 0.03mm.
Pros
- Vicat softening temperature of 104°C, the highest heat figure stated here
- Full print settings stated: nozzle 245-265°C, bed 90-100°C, cooling fan off
- Low-odor resin with lower volatile content than traditional ABS resins
- Vacuum sealed with desiccant; dry at 70°C for 6 hours if it absorbs moisture
Cons
- No warranty term stated
- Enclosed printing chamber recommended, so open machines are a poor match
- No print speed stated
- 1KG spool only; no multi-spool pack stated

Creality ABS 3D Printing Filament 1.75mm
A 1.75mm red ABS spool that states a 1 Year warranty and 12-month after-sales service, with odorless, non-toxic claims and a 1kg spool.
Pros
- States a 1 Year warranty, the only stated term in this guide
- 12-month and 24 hours after-sales service stated
- Odorless, non-toxic claim with no harmful substances emission during printing
- Tough, hard and rigid with good dimensional stability, per the listing
Cons
- No nozzle or bed temperature stated
- No diameter tolerance stated
- No drying guidance stated
- No print speed stated

SUNLU ABS Filament 1.75mm,Red+Klein
A bundle of four 1KG spools in red, Klein Blue, yellow and green, with stated print settings of 250-260°C nozzle and 80-100°C bed and the smallest stated tolerance here, ±0.02mm.
Pros
- Four 1KG spools, the most material in this guide
- Smallest stated tolerance here, ±0.02mm on 1.75mm filament
- Full print settings stated: nozzle 250-260°C, bed 80-100°C, speed 40-60mm/s, retraction 5mm
- Larger inner spool diameter makes unwinding easier, per the listing
Cons
- Only one of the four spools is red; the rest are Klein Blue, yellow and green
- No warranty term stated
- Enclosure recommended during printing
- No drying guidance stated

ELEGOO ABS 3D Printer Filament 1.75mm Red 1KG
A 1.75mm red ABS spool that states heat resistance up to 85°C, vacuum sealed packing, and an enclosed printer requirement.
Pros
- Heat resistant up to 85°C with water resistance stated
- Vacuum sealed packing to keep moisture out
- 1.75mm high-precision diameter for smooth, consistent feeding, per the listing
- Suited to drone mounts, protective cases, rugged outdoor gear and industrial tools, per the listing
Cons
- No nozzle or bed temperature stated
- No diameter tolerance stated
- Enclosed 3D printer required, not just recommended
- No warranty term stated

ANYCUBIC ABS Filament 1.75mm, 1KG Spool (2.2 lbs)
A 1.75mm red ABS spool that states heat resistance up to 85°C and a 220mm x 220mm anti-warping print area with a heated bed at 100°C.
Pros
- Heat resistant up to 85°C
- 220mm x 220mm anti-warping print area with a heated bed at 100°C
- Greater resistance to warping than PLA and PETG, per the listing
- Automatic recognition when paired with ACE Pro, per the listing
Cons
- No nozzle temperature stated
- No diameter tolerance stated
- No warranty term stated
Other machines to compare
Creality ABS Filament 1.75mmCheck price on Amazon
SUNLU High Speed ABS FilamentCheck price on Amazon
Bambu Lab ABS Filament Red 1kg RefillCheck price on Amazon
OVERTURE ABS High Strength 3D Printer Filament 1.75mmCheck price on Amazon
eSUN ABS+ Filament 1.75mmCheck price on Amazon
Specs compared
| Model | HQ Score | Diameter | Spool | Nozzle | Bed | Tolerance | Warranty |
|---|---|---|---|---|---|---|---|
| Polymaker ABS Red | 9.7/10 | 1.75mm | 1KG | 245-265°C | 90-100°C | +/- 0.03mm | Not stated |
| Creality CR-ABS Red | 9.5/10 | 1.75mm | 1KG | Not stated | Not stated | Not stated | 1 Year |
| SUNLU ABS 4-Pack | 9.5/10 | 1.75mm | 4 x 1KG | 250-260°C | 80-100°C | ±0.02mm | Not stated |
| ELEGOO ABS Red 1KG | 9.5/10 | 1.75mm | 1KG | Not stated | Not stated | Not stated | Not stated |
| ANYCUBIC ABS Red 1KG | 9.4/10 | 1.75mm | 1KG | Not stated | 100°C | Not stated | Not stated |
We give each product’s specs as its manufacturer rates them; listings read 11 November 2026.
What the listings tell you, and what they leave out
Five red ABS listings went into this guide. Two state a nozzle temperature, Polymaker at 245-265°C and SUNLU at 250-260°C, and three state a bed temperature, Polymaker at 90-100°C, SUNLU at 80-100°C and Anycubic at 100°C. Two state a diameter tolerance, Polymaker at +/- 0.03mm and SUNLU at ±0.02mm. Only one states a warranty term, Creality at 1 Year. Three call for enclosed printing: ELEGOO requires an enclosed printer, while Polymaker and SUNLU recommend an enclosed chamber or enclosure.
No listing here states a print speed except SUNLU, at 40-60mm/s, and no listing states a price.
Buying guide: choosing the best red abs filament
Nozzle and bed temperatures
Start with the temperatures, since ABS needs heat at the nozzle and on the bed. Polymaker states a nozzle temperature of 245-265°C and a bed temperature of 90-100°C with the cooling fan turned off. SUNLU states a nozzle temperature of 250-260°C and a bed temperature of 80-100°C, with a printing speed of 40-60mm/s. Anycubic states a heated bed at 100°C for its 220mm x 220mm anti-warping print area but no nozzle temperature. ELEGOO and Creality state no nozzle or bed temperature, so their profiles need settings from the printer maker before printing.
Diameter and tolerance
Diameter decides how evenly the filament feeds. All five spools state 1.75mm. Only two state a tolerance: Polymaker at +/- 0.03mm and SUNLU at ±0.02mm. ELEGOO calls its 1.75mm a high-precision diameter, which suits smooth, consistent feeding, but gives no tolerance figure.
Enclosed printing and warping
ABS warps as it cools, so the chamber matters. ELEGOO requires an enclosed 3D printer. Polymaker recommends an enclosed printing chamber to hold a stable printing environment and help reduce warping, especially for larger parts. SUNLU recommends an enclosure during printing. Anycubic claims greater resistance to warping and a 220mm x 220mm anti-warping print area with a heated bed at 100°C. Creality claims no layer separation or warped edges on large objects with edges and corners.
Drying and storage
ABS picks up moisture, and wet filament prints poorly. Polymaker says to dry at 70°C for approximately 6 hours if the filament absorbs moisture, and ships vacuum sealed with desiccant. ELEGOO ships vacuum sealed to prevent moisture and recommends drying out before use. Creality says to place the product in a dry and ventilated environment, away from high temperature, sun and humidity.
Pack size and color
Spool size decides how much red you get. ELEGOO, Polymaker, Anycubic and Creality each state a 1KG spool, with 2.2lbs stated for ELEGOO, Anycubic and Creality. SUNLU is a bundle of four 1KG spools for 4kg in total, but only one spool is red; the others are Klein Blue, yellow and green.
ABS printing needs an enclosed machine and ventilation: ELEGOO requires an enclosed printer, Polymaker and SUNLU recommend an enclosed chamber or enclosure, and Creality says to store the spool in a dry and ventilated environment.
Project Match
- Drone mounts, protective cases, rugged outdoor gear and industrial tools: ELEGOO, which names those uses and states heat resistance up to 85°C.
- Functional prototypes, mechanical parts, robotics, tools, fixtures and replacement parts: Polymaker, which names those uses and states a Vicat softening temperature of 104°C.
- Durable items and functional parts that need higher heat resistance: SUNLU, which states nozzle 250-260°C and a tolerance of ±0.02mm.
- Complex automobile components and chassis for electronic appliances: Anycubic, which names those uses and states a 220mm x 220mm anti-warping area.
- Large objects with edges and corners: Creality, which says printing of such objects is obviously improved over ordinary ABS.
How the scores add up
Each spool is scored on performance, build, value, safety and warranty, with the weights published on the site method page. No listing here states a price, so value scores compare the stated specs and pack size, not cost. Only Creality states a warranty term, so the other four spools score zero on warranty.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Polymaker ABS Red | 9.7 | 33 | 22 | 21 | 5 | 0 |
| Creality CR-ABS Red | 9.5 | 27 | 20 | 20 | 5 | 2 |
| SUNLU ABS 4-Pack | 9.5 | 30 | 21 | 21 | 5 | 0 |
| ELEGOO ABS Red 1KG | 9.5 | 28 | 20 | 21 | 5 | 0 |
| ANYCUBIC ABS Red 1KG | 9.4 | 27 | 20 | 20 | 0 | 0 |
Point totals are scaled so the weakest reads 9.2 and the strongest 9.8, with everything between kept in order.
FAQ: lasers and CNC
What nozzle temperature does red ABS filament need?
Polymaker states a nozzle temperature of 245-265°C, and SUNLU states 250-260°C. ELEGOO, Anycubic and Creality state no nozzle temperature.
Do I need an enclosed printer for ABS filament?
ELEGOO requires an enclosed 3D printer. Polymaker recommends an enclosed printing chamber, and SUNLU recommends an enclosure during printing. Anycubic and Creality state no enclosure requirement.
How do I dry ABS filament before printing?
Polymaker says to dry at 70°C for approximately 6 hours if the filament absorbs moisture. ELEGOO recommends drying out before use and ships vacuum sealed. Keep spools sealed and dry between prints.
What diameter tolerance do red ABS spools state?
Polymaker states +/- 0.03mm and SUNLU states ±0.02mm, both on 1.75mm filament. ELEGOO, Anycubic and Creality state no tolerance.
Does red ABS filament come with a warranty?
Creality states a 1 Year warranty with 12-month and 24 hours after-sales service. The other four listings state no warranty term. SUNLU points buyers to its service team for filament, order or invoice problems, but states no term.
Related: 3d printers, best abs filament 1.75mm, best abs filament for 3d printing, and best white pla filament 1.75mm.




