Best Grease for 3D Printer Z Axis (2026)
Five greases for 3D printer Z-axis lead screws, compared by temperature range, tube size, compatibility and what each listing states about safety.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallB.X BX-300/F9.7/10View on Amazon - 2
Best Value PackUniXYZ 5-Pack Grease9.6/10View on Amazon - 3
Best KitHorex Lithium Grease9.6/10View on Amazon - 4
Best Creality PickCreality 4-Pack Grease9.5/10View on Amazon - 5
Best Single TubeCreality 1-Pack Grease9.5/10View on Amazon
A Z-axis lead screw that drags, squeaks or binds leaves layer lines across a print and shortens the life of the screw, the nut and the rails around it. The best grease for 3d printer z axis is a paste that stays where it is applied, reduces friction and noise, and suits the printer it goes on. This guide compares five greases from the listings, by temperature range, tube size, compatibility and what each listing states about safety, so you can match one to your printer and your prints.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall B.X BX-300/F: Food grade NSF H-1, a stated -20C to +120C range, and Bambu Lab’s own lead screw guide names this grease type. Check price on Amazon
- Best Value Pack UniXYZ 5-Pack Grease: Five 10g tubes with a stated -20°C to 120°C range and a compatibility list naming Bambu Lab, Creality, Anycubic, Elegoo, Flashforge and Voxelab models. Check price on Amazon
- Best Kit Horex Lithium Grease: A 50g tube with finger-cots, brushes and a scraper, and a stated -20℃ to 120℃ range. Check price on Amazon
- Best Creality Pick Creality 4-Pack Grease: A 4-pack of high viscosity grease from Creality, stated for Z-axis lead screws, linear rods and guide rails. Check price on Amazon
- Best Single Tube Creality 1-Pack Grease: One paste tube from Creality, non-toxic and odorless, stated for all 3D printers. Check price on Amazon
Machines on the list

BX-300/F 3D Printer Lead Screw Grease for Bambu
A food grade synthetic grease for lead screws, stated to reduce Z-axis binding, layer lines and noise, in a 1.05 oz tube.
Pros
- NSF H-1 food grade formula, the only food grade pick here
- Stated -20C to +120C range, with anti-wear additives
- Bambu Lab lead screw guide names this grease type for P1S, X1C and H2D
- Reapply interval stated: every 3 to 6 months or 500 to 1000 print hours
Cons
- No warranty term is stated
- Single 30g tube, no pack option in the listing
- No applicator brush or scraper is named in the listing
- Four-ball wear performance is a maker claim with no method in the listing

UniXYZ 5PK 3D Grease for Bambu Lab P1S P2S P1P H2D
Five 10g tubes of mineral oil grease with a stated -20°C to 120°C range, listed for Bambu Lab, Creality, Anycubic, Elegoo, Flashforge and Voxelab printers.
Pros
- 5 tubes of 10g, the most tubes in this guide
- Stated -20°C to 120°C range, stable across long print sessions
- Precision tube design for targeted application to vertical and horizontal rods
- Compatibility list names Bambu Lab, Creality, Anycubic, Elegoo, Flashforge and Voxelab models
Cons
- No warranty term is stated
- Do not apply to X/Y-axis guides of high-speed printers like Bambu Lab
- Mineral oil base, not a synthetic formula
- Thin coat only on X/Y rails of non-high-speed printers

Horex 3D Printer Lithium Grease 50g Lubricant
A white lithium grease kit with a stated -20℃ to 120℃ range, a 50g tube, finger-cots, brushes and a scraper for lead screws and rails.
Pros
- Stated -20℃ to 120℃ range, listed as -4℉ to 248℉
- Kit includes 2 finger-cots, a double-headed brush, a scraper and a single-headed brush
- Stated for lead screws, X/Y/Z axis, gears, linear rails and POM anti-backlash nuts
- Will not drip, melt or separate, per the listing
Cons
- No warranty term is stated
- Title says 50g and the bullets say 50ml, so the size is unclear
- Some materials may react to this grease, per the listing
- Brush and scraper sizes are small, per the listing note

Creality 3D Printer Lubricant Grease, Non-Toxic
A 4-pack of high viscosity grease from Creality, stated for Z-axis lead screws, linear rods, guide rails, bearings, gears and stepper motor shafts.
Pros
- 4 tubes, the second largest pack here
- High viscosity formula that stays where applied, with no dripping
- Non-toxic and non-corrosive, stated safe for all 3D printer parts
- Stated for Z-axis lead screws, linear rods, guide rails and gears
Cons
- No warranty term is stated
- No temperature range is stated
- No tube size or weight is stated
- No reapply interval is stated

Creality Official Lubricant Grease
One tube of Creality paste grease, non-toxic and odorless, stated for all 3D printers and their lead screws, rails and rods.
Pros
- Paste form that adheres to the surface and is not easy to dry or flow
- Non-toxic, colorless and odorless, meets certified environmental standards
- Rust and corrosion resistant, per the listing
- Stated for all 3D printers, with Z-axis lead screws named
Cons
- No warranty term is stated
- No temperature range is stated
- One tube only, the smallest pack here
- No reapply interval is stated
Other machines to compare
Creality Thermal GreaseCheck price on Amazon
Creality High-Temperature Thermal GreaseCheck price on Amazon
Magnalube-G All-Purpose PTFE GreaseCheck price on Amazon
Specs compared
| Model | HQ Score | Type | Temp range | Size | Compatibility | Safety statement | Warranty |
|---|---|---|---|---|---|---|---|
| B.X BX-300/F | 9.7/10 | Synthetic + fluorine, food grade | -20C to +120C | 1.05 oz / 30g | Bambu Lab P1S, X1C, H2D | NSF H-1 food grade | Not stated |
| UniXYZ 5-Pack Grease | 9.6/10 | Mineral oil | -20°C to 120°C | 10g per tube, 5 tubes | Bambu Lab, Creality, Anycubic, Elegoo, Flashforge, Voxelab | Non-toxic, odorless, non-volatile | Not stated |
| Horex Lithium Grease | 9.6/10 | White lithium | -20℃ to 120℃ | 50g | Bambu, Ender, Prusa and more | Non-toxic, odorless | Not stated |
| Creality 4-Pack Grease | 9.5/10 | High viscosity paste | Not stated | 4 tubes | Creality printers | Non-toxic, non-corrosive | Not stated |
| Creality 1-Pack Grease | 9.5/10 | Paste | Not stated | 1 tube | All 3D printers | Non-toxic, odorless | Not stated |
We give each product’s specs as its manufacturer rates them; listings read 10 November 2026. Temperature ranges are stated in Celsius unless the listing gives Fahrenheit too.
What the listings tell you, and what they leave out
This guide compares 5 listings. 3 state a temperature range: B.X BX-300/F, UniXYZ and Horex all state -20 to 120. 1 states a reapply interval: B.X BX-300/F, every 3 to 6 months or 500 to 1000 print hours. None of the 5 states a warranty term, and 2 state no temperature range: the Creality 4-pack and the Creality 1-pack.
One listing contradicts itself on size: Horex says 50g in the title and 50ml in the bullets. One listing carries a use warning: UniXYZ says do not apply its grease to the X/Y-axis linear guides and smooth rods of high-speed printers like Bambu Lab, and to follow the printer’s own maintenance guide. Follow that guide before applying any grease to a high-speed printer.
Buying guide: best grease for 3d printer z axis
Grease or oil
The picks here are greases: pastes that stay where they are applied. The Creality 4-pack listing calls out a high viscosity formula that prevents dripping, and the Creality 1-pack listing says its paste is not easy to dry or flow. For oil, see the best 3d printer lubricant oil picks.
Temperature range
3 of the 5 picks state a range, and all 3 state -20 to 120. B.X BX-300/F states -20C to +120C, UniXYZ states -20°C to 120°C, and Horex states -20℃ to 120℃, listed as -4℉ to 248℉. The 2 Creality picks state no range, so a printer that runs hot has no stated figure to lean on with those.
Food grade and non-toxic claims
Only B.X BX-300/F states a food grade formula, NSF H-1 compliant, which the listing ties to printers used for kitchenware or toys. The other 4 picks state non-toxic formulas: Creality 4-pack adds non-corrosive, Creality 1-pack adds colorless and certified environmental standards, UniXYZ adds odorless and non-volatile, and Horex adds odorless. Non-toxic is a maker claim in each listing, not a certification, except where a standard is named.
Where not to use it
UniXYZ warns against its grease on the X/Y-axis linear guides and smooth rods of high-speed printers like Bambu Lab, and says a thin coat works on X/Y rails only for non-high-speed printers. Horex warns that some materials may react to a grease of its type and to confirm the use case before applying it. For any printer, the maker’s own maintenance guide is the final word on where grease goes.
How often to reapply
Only B.X BX-300/F states an interval: every 3 to 6 months or 500 to 1000 print hours, depending on use. The other listings say their grease lasts a long time without giving a figure. If your Z axis grows noisy or layer lines return, clean the screw and reapply, then check the result on a short print.
Project Match
- Kitchenware or toy prints: B.X BX-300/F, the only food grade NSF H-1 pick here.
- Bambu Lab P1S, X1C or H2D lead screws: B.X BX-300/F, the grease type Bambu Lab’s own guide names, or UniXYZ 5-Pack Grease, which lists the same models.
- Creality printers: Creality 4-Pack Grease or Creality 1-Pack Grease, both stated for Creality parts; UniXYZ also lists Ender 3 V3 SE, V3 Max and K1 SE.
- CNC or engraving machine screws: Horex Lithium Grease, stated for CNC machine guide screws and engraving machine screws.
- High-speed printer X/Y rails: none of these picks, since UniXYZ warns against grease on the X/Y guides of high-speed printers; follow the printer’s own maintenance guide.
How the scores add up
Each grease is scored out of 10 on performance, build, value, safety and warranty, with the weights published on the How We Pick page. A spec the listing does not publish scores nothing.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| B.X BX-300/F | 9.7 | 32 | 22 | 21 | 8 | 0 |
| UniXYZ 5-Pack Grease | 9.6 | 30 | 21 | 21 | 7 | 0 |
| Horex Lithium Grease | 9.6 | 29 | 21 | 21 | 5 | 0 |
| Creality 4-Pack Grease | 9.5 | 28 | 20 | 20 | 5 | 0 |
| Creality 1-Pack Grease | 9.5 | 27 | 20 | 19 | 5 | 0 |
Point totals are scaled so the weakest reads 9.2 and the strongest 9.8, with everything between kept in order.
FAQ: lasers and CNC
How often should I grease a 3D printer Z axis?
Only B.X BX-300/F states an interval: every 3 to 6 months or 500 to 1000 print hours, depending on use. The other 4 picks say their grease lasts a long time without giving a figure.
Can I use the same grease on the X and Y axes?
It depends on the printer. Horex states its grease for X/Y/Z axis parts, while UniXYZ says do not apply its grease to the X/Y-axis linear guides and smooth rods of high-speed printers like Bambu Lab. Follow your printer’s own maintenance guide.
What is the difference between grease and lubricant oil for a 3D printer?
Grease is a paste that stays where it is applied: the Creality 4-pack listing calls out a high viscosity formula that prevents dripping. Oil flows and spreads, and is covered in the best 3d printer lubricant oil picks.
Is food grade grease needed for a 3D printer?
Only where prints touch food or toys. B.X BX-300/F is the only pick here with an NSF H-1 food grade formula, and its listing ties that to printers used for kitchenware or toys. For other prints, a non-toxic formula is what the listings offer.
Does grease fix Z-axis binding and layer lines?
B.X BX-300/F is the only pick whose listing says it addresses Z-axis binding, layer lines and noise. Grease is maintenance for a lead screw that is clean and sound; a bent screw or a worn nut needs a part, not a lubricant.
Related: the 3d printer hub, 3d printer maintenance, and the best 3d printer bed adhesive picks. Also see the best heat resistant 3d printer filament and 3d printer nozzle size.




