800w vs 1.5kw Spindle: Which One Should You Buy?
Air cooled CNC spindle kits for desktop routers, compared on power, speed, bearings, runout, collets and the controller in the box.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
800W 110VDC CNC Spindle Motor Kit ER11 Air Cooled9.5/10View on Amazon - 2
CNC Spindle Motor Kits, 110V 1.5KW Air Cooled9.5/10View on Amazon
A sign blank needs a clean edge, a hardwood plaque needs a pocket cut to depth, or a small batch of parts needs the same cut repeated without drift. The spindle on a desktop CNC router shapes how clean that cut comes out and how hard the machine can push. The 800w vs 1.5kw spindle question comes down to power, speed range and what ships in the box, and the kits below show each side of it.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Verdict: pick the 1.5KW kit for more power, a VFD and a fuller box with collets and wiring. Pick the 800W kit for a stated speed range, Mach3 control and overcurrent protection. Choose by the cuts you plan to make.
Machines on the list

800W 110VDC CNC Spindle Motor Kit ER11 Air Cooled
An 800W air cooled spindle kit with a Mach3 speed controller, a 52 mm mount clamp and a stated 5000-20000 r/min speed range.
Pros
- 800W with a stated 5000-20000 r/min speed range and 0.79 NM torque
- Mach3 speed controller with a 6A current limit and AC100-220V input
- Overcurrent protection cut-off and a soft start device
- Air cooled with a rear cooling fan and a 52 mm mount clamp
Cons
- 800W gives less power than the 1.5KW kit
- No ER11 collets are included in the kit
- 52 mm mount is narrower than the 65 mm clamp on the 1.5KW kit
- Speed control runs through the Mach3 controller, with no VFD in the kit

CNC Spindle Motor Kits, 110V 1.5KW Air Cooled
A 1.5KW air cooled spindle kit with a VFD, a 65 mm clamp mount, 3 ER11 collets and a stated runout under 0.005 mm.
Pros
- 1.5KW spindle with a 110V VFD included in the kit
- 4 upgraded steel bearings and dynamic balance technology
- Runout less than 0.005 mm as stated
- 3 ER11 collets, a 3 meter shielded wire and 2 wrenches in the box
Cons
- Speed range is not stated in the listing
- No warranty term is stated
- 65 mm clamp mount needs a 65 mm mount on the machine
- Collets cover 1/4, 1/8 and 1/16 inch only
Other machines to compare
LUNYEE 8080 Pro Max CNC Router MachineCheck price on Amazon
LUNYEE 4040 Nova CNC Router MachineCheck price on Amazon
FoxAlien 800W Desktop Dust Collector HFS-800Check price on Amazon
Side by side
| HQ Score | Power | Speed | Collet | Clamp | |
|---|---|---|---|---|---|
| RATTMMOTOR 800W | 9.5/10 | 800W | 5000-20000 r/min | ER11 | 52 mm |
| Zhong Hua Jiang 1.5KW | 9.5/10 | 1.5KW | Not stated | ER11 | 65 mm |
We give each product’s specs as its manufacturer rates them; listings read 23 October 2026.
800w vs 1.5kw spindle: power and speed
The 1.5KW spindle gives more power than the 800W spindle: 1.5KW against 800W, both at 110V. More power suits heavier cuts and harder material, while the 800W kit suits lighter work on a desktop router. The 800W kit states a speed range of 5000-20000 r/min with 0.79 NM of torque, and the controller holds speed with pulse width technology. The 1.5KW kit states no speed range, so its RPM cannot be compared with the 800W kit, and no torque figure is stated for it either.
What comes in the box
The 800W kit pairs the spindle with a Mach3 speed controller, a power supply converter and a 52 mm mount clamp. The controller takes AC100-220V input with a 6A current limit and supports Mach3 control, and the motor supports reverse rotation. The 1.5KW kit pairs the spindle with a 110V VFD, a 65 mm clamp mount, 3 ER11 collets in 1/4, 1/8 and 1/16 inch, a 3 meter shielded 18AWG aviation wire, a power wire and 2 wrenches. The VFD comes pre-programmed for basic parameters, and the maker states the kit takes 5 minutes to install.
Bearings, runout and build
The 1.5KW spindle runs on 4 upgraded steel bearings with dynamic balance technology, and the stated runout is less than 0.005 mm. The maker states the bearings extend working life, and the dynamic balance reduces noise and increases stability in the working process. The 800W spindle runs in an aluminum body with a rear cooling fan and a 3.18 mm shaft, and the kit states an item weight of 1.7 kg. No runout figure is stated for the 800W spindle.
Materials
The 1.5KW kit lists plastics, soft aluminum, brass, acrylics, PCB, wood, plywood and nylon among the drilling and engraving materials it handles. The 800W kit states no materials list, so match the spindle to the material by its power and speed range instead. For end mill choice by material, see the types of end mills guide and the router bit speed chart.
Safety and control
The 800W kit adds an overcurrent protection cut-off device and a soft start device, and the motor supports reverse rotation. The speed controller takes AC100-220V input, so it suits mains supplies in the stated range. The 1.5KW kit states no safety features, and its VFD comes pre-programmed for basic parameters. Clamp the work, wear eye and ear protection, keep hands clear of the spinning cutter, and never leave a running spindle unattended.
Choose the 800W kit if
- You want a stated speed range of 5000-20000 r/min and a stated torque of 0.79 NM.
- You want Mach3 control with overcurrent protection and a soft start device.
- You want a compact kit, with a stated item weight of 1.7 kg and a 52 mm mount.
Choose the 1.5KW kit if
- You want more power for heavier cuts, with a VFD in the box.
- You want 3 ER11 collets, a 3 meter shielded wire and 2 wrenches included.
- You want stated runout under 0.005 mm and 4 upgraded steel bearings.
For collet types, see the ER vs TG collets guide, and for shank sizes see the router bit shank sizes guide.
Clamp the work before the spindle starts, wear eye and ear protection, and keep hands and loose clothing clear of the spinning cutter. Never touch a bit while it spins, and stay with the machine while it runs.
FAQ: lasers and CNC
Is a 1.5KW spindle better than an 800W spindle?
For power, yes: the 1.5KW spindle gives more power than the 800W spindle, and it ships with a VFD and 3 collets. The 800W kit answers with a stated speed range, Mach3 control and overcurrent protection. Neither is better for every job; choose by the cuts you plan to make.
What speed does the 1.5KW spindle run at?
The listing states no speed range for the 1.5KW spindle, so its RPM cannot be compared with the 800W kit. The 800W kit states a speed range of 5000-20000 r/min. Check the maker specifications for the 1.5KW spindle before you plan cuts by speed.
Do these spindle kits include collets?
The 1.5KW kit includes 3 ER11 collets in 1/4, 1/8 and 1/16 inch. The 800W kit states an ER11 spindle but no collets in the box, so buy collets to suit the bits you plan to run.
Can I run the 800W spindle on 220V?
The 800W speed controller takes AC100-220V input, so it covers 110V and 220V mains in the stated range. The spindle itself is a 110V motor, and the controller converts the input for it.
Which spindle is better for a beginner?
Both kits suit a newcomer to CNC spindles. The 1.5KW kit arrives with a pre-programmed VFD and takes 5 minutes to install as stated, while the 800W kit gives a stated speed range and Mach3 control. Pick the kit whose stated figures match the work you plan to do.
Related: types of end mills, ER vs TG collets, router bit speed chart and best cordless rotary tool.




