Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Serger Troubleshooting: Common Problems and Fixes

A step-by-step guide to fixing skipped stitches, broken thread, puckering and looping seams on a home serger, starting with the thread path and the needles.

Serger Troubleshooting: Common Problems and Fixes
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 111.22"-18.31" Adjustable Cone Thread Holder for Sewing Machine11.22"-18.31" Adjustable Cone Thread Holder for Sewing Machine9.7/10View on Amazon
  2. 2SINGER® Professional 14T968DC Heavy-Duty Serger Overlock withSINGER® Professional 14T968DC Heavy-Duty Serger Overlock with9.7/10View on Amazon
  3. 3Juki MO-80CB Free-Arm Serger Overlock MachineJuki MO-80CB Free-Arm Serger Overlock Machine9.7/10View on Amazon

Serger troubleshooting starts with the thread path, the needles and the tension dials. Most skipped stitches, broken thread, puckered seams and looping edges come from the thread path, the needles or the tension dials, and each one has a clear fix. The steps below walk through them in order, from re-threading the machine to matching the thread and needle to the fabric.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

This guide gives no tension numbers or stitch settings, because the listings used here state no such figures. Move a dial a small amount at a time and check the seam on scrap fabric after each change.

Step 1: Re-thread the machine in order

A serger that worked well and now skips stitches often has a thread that slipped out of a guide or off a tension disc. Lift the presser foot, which opens the tension discs, and pull each thread out. Then thread the loopers before the needles, following the color-coded path printed on the machine or in the manual. Seat each cone on its spindle so it turns freely, and keep the thread stands upright so the cones feed without catching.

Threading the loopers takes patience, because they sit deep in the machine. A long threader reaches them without forcing the thread. The GUZE-US set lists a needle threader at 13.6 cm and a looper threader at 11.2 cm, and each one is made to pass thread through the eye of a needle or looper. If the machine still skips stitches after a full re-thread, the needles are the next place to look. New owners can also work through the serger machine for beginners guide for the full setup order.

Step 2: Check the needles

A bent, dull or wrong-size needle is a common cause of skipped stitches and broken thread. Remove the needles and roll each one on a flat surface to check for a bend, then fit fresh needles and push each one up as far as it goes before tightening the screw. A needle that sits low will miss the loopers and leave gaps in the seam.

Superior Threads calls the HAx1SP the standard, go-to needle style for serger and overlock machines. It lists its HAx1SP serger needles in size #75/11, 5 per pack, for 3-thread and 4-thread sergers. If the machine manual recommends a 130/705H needle style, the maker states the HAx1SP can be used in its place. Change the needles when the stitch quality changes, rather than waiting for a needle to break. The best beginner serger guide lists machines that use the same needle style.

Step 3: Match the thread

Serger thread comes on large cones, and the weight matters. The listings used here are 40s/2 (Tex27) spun polyester, a common serger weight that the makers list for serging and overlocking. Using the same thread weight on the loopers and the needles makes the tensions easier to balance across the stitch. Mixing weights can pull the seam to one side or leave loops on the edge.

Cones are sold in sets. WAFASSZD lists 4 cones of 3000 yards each, 12,000 yards in total. FUNZON lists 8 cones, 4 black and 4 white, with 3000 yards on each cone. StiVerse lists 12 cones of 1800 yards each, 21,600 yards in total. Keep spare cones of the colors used most, and replace thread that frays or sheds lint. A serger thread holder keeps cones upright and feeding smoothly when the machine has no built-in stand.

Step 4: Balance the tension dials

When the seam loops off the edge or the stitches look loose on one side, the tension is out of balance. Adjust a single dial a small amount at a time, then sew a scrap seam and look at the result before touching another dial. The looper threads should meet at the edge of the fabric, and the needle threads should sit flat on the fabric without pulling it in.

Change a single thing at a time, so the cause stays clear. If the loops sit on top of the fabric, tighten the needle tension a small amount. If the loops hang below the edge, tighten the looper tension a small amount. If nothing changes after several small moves, re-thread the machine and check the needles again before going further. The embroidery machine tension issues guide covers thread balance too.

Step 5: Feed the fabric without pushing or pulling

Pushing or pulling the fabric through a serger stretches the seam and can bend a needle. Guide the fabric lightly and let the feed dogs move it. For knit fabric, support the weight of the piece so it does not hang off the table and pull against the needles. For woven fabric, keep the cut edge lined up with the blade so the stitch wraps the edge instead of missing it.

The thread weight suits the fabric here too. FUNZON lists its 40s/2 polyester thread as suitable for serging and overlocking on woven and knit fabrics. If the seam puckers on light fabric, check the tension first, then the needle size, and sew a scrap seam after each change.

Step 6: Clear lint and check the blade

Lint builds up around the loopers and feed dogs, and a thread nest under the plate can stop the fabric moving. Switch the machine off, open the looper cover, and brush the lint out with the brush that came with the machine. Remove any wrapped thread from around the loopers with tweezers, taking care not to nick the loopers.

Check the cutting blade as well. A dull blade chews the fabric edge instead of cutting it cleanly, and the stitch then has no firm edge to wrap. If the edge looks torn or frayed after trimming, the blade needs attention. The serger vs sewing machine guide explains where a serger fits beside a regular machine, so the blade and the stitch stay in their own roles.

Common mistakes to avoid

  • Threading the needles before the loopers.
  • Mixing thread weights without re-checking the tension.
  • Moving more than a single tension dial at a time.
  • Pushing or pulling the fabric through the machine.
  • Sewing with a bent needle after a jam.

Serger troubleshooting: the short version

  1. Re-thread the loopers before the needles.
  2. Fit fresh needles in the size the manual lists for the fabric.
  3. Use 40s/2 (Tex27) thread on the loopers and needles.
  4. Move a single tension dial a small amount at a time.
  5. Guide the fabric and let the feed dogs move it.
  6. Clear lint from the loopers and check the blade.

FAQ: lasers and CNC

Why does my serger skip stitches?

A missed guide, a thread off a tension disc, or a bent needle are the usual causes. Re-thread the loopers before the needles, fit fresh needles in the size the manual lists for the fabric, and sew a scrap seam to check the result.

Why does serger thread keep breaking?

Old or frayed thread, a burr on a needle, or tension set too tight can break the thread. Replace the thread with fresh 40s/2 (Tex27) polyester, fit a fresh needle, and loosen the tension a small amount at a time.

Why is my serged seam puckering?

Puckering comes from tension that pulls the fabric in, or from a needle that is too large for the fabric. Loosen the tension a small amount, then try a fresh needle in the size the manual lists for the fabric and sew a scrap seam to compare.

Why does the stitch loop off the edge of the fabric?

Loops off the edge mean the looper tension is loose, or the fabric edge missed the blade. Tighten the looper tension a small amount at a time and keep the cut edge lined up with the blade so the stitch wraps it.

What needle does a home serger use?

Check the machine manual for the needle style it takes. Superior Threads lists its HAx1SP needles in size #75/11, 5 per pack, for 3-thread and 4-thread sergers, and states the HAx1SP can be used in place of a 130/705H needle style when the manual recommends it.

Related: the sewing and embroidery machines hub, serger machine for beginners and best beginner serger. Also see the coverstitch vs serger guide. Also see the sewing and embroidery machines hub.

More buying guides

Craft Machines ·

Button Maker Troubleshooting: Common Fixes

Button maker troubleshooting starts with matching the die to the button, cutting the fabric to the stated size, and setting the press height before…

Craft Machines ·

DTF Printer Troubleshooting: Common Fixes

A step-by-step guide to DTF printer troubleshooting: read the print, check the nozzles, clean the printhead and clear white ink clogs before the next…

CNC Routers ·

Stepper Motor Troubleshooting for CNC Machines

A practical stepper motor troubleshooting guide for CNC machines: trace stalls, missed steps and overheating to power, wiring and driver settings, then pick the…