Bias Tape Maker Size Chart: Choosing the Right Width
A bias tape maker size chart matching each stated maker size to its stated fabric cut width, with the cutting and feeding steps the makers publish.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Bias Tape Makers Kit of 5 Sizes 1/4" 3/8" 1/2"9.6/10View on Amazon - 2
HONEYSEW Bias Tape Maker Set9.6/10View on Amazon - 3
5 Sizes Bias Tape Makers Kit9.6/10View on Amazon - 4
YICBOR Bias Tape Maker Set 6MM/9MM/12MM/18MM/25MM9.5/10View on Amazon
A quilt edge needs a neat folded strip of fabric, and choosing the wrong maker width leaves that strip too narrow to cover the raw edge or too wide to sit flat. The bias tape maker size chart below matches each maker size to the fabric strip width stated for it, where the maker states one, so the bias tape maker size chart question has a direct answer: cut the strip to the stated width for the maker size you plan to use, feed it through wrong side up, and press the folds as the strip comes out. The chart uses the cut widths stated for the MUDESEN set, the only set here that states a cut width for each of its sizes.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Bias Tape Makers Kit of 5 Sizes 1/4" 3/8" 1/2"
A set of 5 bias tape makers in 6mm, 9mm, 12mm, 18mm and 25mm with a stated cut width for every size.
Pros
- Stated cut width for every size, from 12mm to 46mm
- 5 sizes stated in inches and millimeters
- Folds fabric into halves as the strip is pulled through
- Stated steps for cutting, feeding and pressing
Cons
- No 50MM size is stated
- No storage box is stated
- No awl or needles are stated in the contents
- No warranty term is stated

HONEYSEW Bias Tape Maker Set
A bias tape maker set stating 6MM, 9MM, 12MM, 18MM, 25MM and 50MM sizes.
Pros
- 50MM size stated, the widest here
- Six sizes stated in millimeters
- Items stated as set in slots with instructions
- Folds fabric ready for sewing or gluing, per the maker
Cons
- No cut width is stated for any size
- No awl or needles are stated in the contents
- No warranty term is stated
- No fabric types are stated for this set

5 Sizes Bias Tape Makers Kit
A bias tape maker kit stating 1/4, 3/8, 1/2, 3/4 and 1 inch sizes with a sewing awl, bead needles and a storage box.
Pros
- Sewing awl and bead needles stated in the contents
- Storage box stated for the tools
- Compatibility with cotton, silk and linen stated
- Stated steps for cutting, feeding and pressing
Cons
- No cut width is stated for any size
- No 50MM size is stated
- Warranty description stated as NO
- Sizes stated in inches only, with no millimeter sizes stated

YICBOR Bias Tape Maker Set 6MM/9MM/12MM/18MM/25MM
A bias tape maker set stating 6MM, 9MM, 12MM, 18MM and 25MM sizes.
Pros
- 5 sizes stated in millimeters and inches
- Items stated as set in slots
- Folds fabric ready for sewing or gluing, per the maker
- Covers the standard chart rows from 6mm to 25mm
Cons
- No cut width is stated for any size
- No 50MM size is stated
- No awl, needles or box are stated
- No cutting or feeding steps are stated
Bias tape maker size chart
Maker sizes are stated in inches and millimeters: 1/4 inch as 6mm, 3/8 inch as 9mm, 1/2 inch as 12mm, 3/4 inch as 18mm, 1 inch as 25mm, plus a stated 50MM size listed as 2 inch.
| Maker size | Stated cut width |
|---|---|
| 6mm (1/4 inch) | 12mm |
| 9mm (3/8 inch) | 18mm |
| 12mm (1/2 inch) | 24mm |
| 18mm (3/4 inch) | 36mm |
| 25mm (1 inch) | 46mm |
| 50MM (2 inch) | Not stated |
Pick the maker size for the finished width, then cut the strip at the stated cut width for that size; no cut width is stated for the 50MM size.
How to cut and feed the strip
Cut across the fabric at a 45-degree angle, then cut strips parallel to that edge at the chart width. Feed the strip wrong side up into the wide end, pull it through with an awl, pin the end to the ironing board, and keep the iron close to the maker so folds press as they form.
For cutting strips cleanly, see our rotary blades for quilting and sewing guide.
Gear for this task
Each set below handles the folding step in the chart above, turning a cut strip into pressed bias tape ready for sewing or gluing.
Choosing a set by stated sizes
Three sets state the same five sizes: 6mm, 9mm, 12mm, 18mm and 25mm. The HONEYSEW set adds 50MM. The MUDESEN set alone states a cut width for every size. The BUTUZE set adds an awl, bead needles and a box. For needle choices, see our sewing machine needle for cotton guide.
FAQ: lasers and CNC
What fabric width do I cut for a 12mm bias tape maker?
The MUDESEN maker (on Amazon) states 24mm for the 12mm size, 12mm for 6mm, 18mm for 9mm, 36mm for 18mm and 46mm for 25mm.
Which set here includes a 50MM maker?
The HONEYSEW set states 6MM, 9MM, 12MM, 18MM, 25MM and 50MM sizes. No cut width is stated for the 50MM size.
How do I cut bias strips?
Cut at a 45-degree angle, then cut strips parallel to that edge at the chart width, and feed the strip wrong side up through the maker.
Which fabrics do these makers state?
The BUTUZE maker (on Amazon) states compatibility with cotton, silk and linen for quilting, garment making and crafts. The other makers state making bias tape from fabric for accents, borders and trim, with no fabric list stated.
Related: the sewing and embroidery machines hub, rotary blades and how to use sewing pins.




