Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Parts of a CNC Router: Labeled Guide

A plain-language guide to the parts of a CNC router, from the spindle and gantry to the controller, collets and workholding.

Parts of a CNC Router: Labeled Guide
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1SeekLiny 10pcs 4040 L Corner Bracket Joint Plate ConnectorSeekLiny 10pcs 4040 L Corner Bracket Joint Plate Connector9.6/10View on Amazon
  2. 2Fgruh 1120PCS M3 Socket Screws Assortment KitFgruh 1120PCS M3 Socket Screws Assortment Kit9.6/10View on Amazon
  3. 3Zeberoxyz 2PCS Set GT2 Synchronous Wheel 20&60 Teeth 5mm BoreZeberoxyz 2PCS Set GT2 Synchronous Wheel 20&60 Teeth 5mm Bore9.5/10View on Amazon

Picture a sign blank clamped to a bed, a carving bit spinning above it, and a frame holding every part square while the cut takes shape. That scene is the parts of a cnc router working as a team: a rigid frame, a moving gantry, a spindle that holds the bit, a controller that sets the speed, and workholding that keeps the material still. The sections below name each part and show the rated figures that separate one spindle kit from another.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

Power, speed and runout figures in this guide are rated figures from the spindle kits named in each section, not measured results from a finished cut.

Parts of a CNC Router at a Glance

CNC routers share the same core parts, listed below and explained in the sections after the table.

Part What it does
Frame Holds the bed, rails and gantry square and steady.
Gantry Carries the spindle across the bed.
Spindle Spins the bit that cuts the material.
VFD and controller Control spindle speed and axis motion.
Stepper motors Move the gantry and spindle along the rails.
Collets and bits Grip the bit and shape the cut.
Bed and workholding Support the material and hold it still.
Dust collection Clears chips and dust from the cut.

The Frame and Gantry

The frame is the skeleton of the machine. It holds the bed flat, keeps the rails parallel, and gives the gantry a steady path. A frame that flexes under load shows up in the cut as chatter and wavy edges, so makers build frames from steel or aluminum and brace the corners. The gantry rides on the frame and carries the spindle assembly. Linear rails guide the gantry along the bed while the spindle moves up and down for depth. When a router loses accuracy, check the frame, rails and gantry first.

The Spindle

The spindle spins the bit and sets the cutting power of the machine. The spindle kits in this guide are air-cooled or water-cooled motors rated from 500W to 4.5kW. A FoxAlien 1.5kW kit (on Amazon) spins at 24,000 RPM with runout under 0.005mm, while a NYMOLABS 710W spindle (on Amazon) offers 6-speed settings from 7,000 to 30,000 RPM with runout within 0.05mm. A Coolook 500W spindle (on Amazon) is rated at 12,000 RPM with runout of 0.01 to 0.03mm, and a CNCTOPBAOS 4.5kW spindle (on Amazon) runs from 10 to 18,000 rpm with an ER32 collet. A RATTMMOTOR 2.2kW water-cooled spindle also reaches 24,000 RPM.

Spindle diameter decides which mount fits: common sizes in these kits are 65mm, 80mm and 52mm. A 65mm FoxAlien spindle and a 65mm Zhong Hua Jiang spindle share the same mount size, while RATTMMOTOR kits use an 80mm mount and MYSWEETY and Coolook kits use a 52mm bracket. Several kits state 4 bearings. The FoxAlien kit includes a 1/4 inch collet with the option of other ER11 sizes.

Cooling splits spindles into air-cooled and water-cooled designs. Air-cooled spindles use a fan and need no coolant, while water-cooled spindles pair with a pump and a water loop. The RATTMMOTOR water-cooled kits include an 80W water pump rated at 3500L/H with a 3.5M head, and the pump must stay fully immersed in water while it runs. Compare the cooling styles in the air cooled vs water cooled spindle guide.

The Controller and the VFD

The VFD, or variable frequency drive, turns wall power into the frequency the spindle needs. A 110V or 220V input feeds the drive, and the drive outputs up to 400Hz for a 24,000 RPM spindle or 300Hz for an 18,000 rpm spindle. Several kits ship with the VFD pre-programmed: a kit states the spindle connects to the VFD in 2 minutes, and another states the full install takes 5 minutes. An aviation plug joins the spindle and the drive, with ports 1, 2 and 3 joining drive ports U, V and W, and port 4 as the ground wire.

The control box holds the speed controller and the wiring in a dustproof housing. The Coolook kit includes an integrated control box with a speed controller, and the supply takes AC 110V or 220V at 50/60Hz and outputs DC 48V at 0 to 12.5A. The MYSWEETY kit pairs its spindle with a speed power converter that takes AC110V or 220V at 50/60Hz. Keep the control box ventilated and clear of dust and vibration.

Collets, Bits and Tool Holding

The collet is the sleeve that grips the bit inside the spindle, and its size decides which bit shanks fit. ER11 collets grip shanks from 1mm to 7mm, and ER11 sets in these kits come in 13-piece and 7-piece sets. ER20 collets take 1/2 inch, 1/4 inch and 1/8 inch shanks, and ER32 collets fit the larger 4.5kW spindles. Runout decides how true the bit spins: several kits state runout under 0.005mm, the CNCTOPBAOS ER32 collet states runout under 0.002mm, and the MYSWEETY ER11 (on Amazon) set states a runout tolerance of 0.01mm. Match the collet to the shank, since a loose grip leaves chatter marks and breaks bits.

Bits do the cutting, and the spindle kits in this guide ship with starter sets: the MYSWEETY kit includes 10 V-bit cutters, and the Zhong Hua Jiang 2.2kW kit includes 3 ER20 collets in 1/2 inch, 1/4 inch and 1/8 inch sizes. The NYMOLABS spindle takes 1 to 8mm, 1/8 inch and 1/4 inch shank tools, and the FoxAlien kit includes a 1/4 inch collet with other ER11 sizes available.

Motors, Motion and the Bed

Stepper motors move the gantry and the spindle along the rails, turning a screw or belt that sets how far the axis travels per turn. The types of stepper motors guide covers the motor styles used on CNC builds. Limit switches mark the ends of travel so the machine knows where the axes stop.

The bed is the flat surface the material rests on, and workholding keeps it still while the bit cuts. Clamps, screws and tape hold sheet goods, and a spoilboard under the sheet takes the through cuts so the bed stays flat. Check the bed for flatness before a long job.

Dust Collection, Cooling and the Workspace

Routing throws chips and fine dust, so dust collection is a working part of the machine. A dust shoe around the spindle pulls chips away from the cut. Water-cooled spindles add a cooling loop: the RATTMMOTOR kits run an 80W pump at 3500L/H with a 3.5M head, and the pump must stay immersed while it runs. Air-cooled spindles skip the loop and rely on a fan. Keep the workspace ventilated and hands clear of the spindle while it spins.

FAQ: lasers and CNC

What does the spindle do on a CNC router?

The spindle spins the cutting bit. It holds the bit through a collet, sets the cutting speed in RPM, and supplies the power that drives the bit through wood, acrylic, aluminum, copper and plastics.

What is the difference between an air-cooled and a water-cooled spindle?

An air-cooled spindle uses a fan and needs no coolant, while a water-cooled spindle pairs with a pump and a water loop. The RATTMMOTOR water-cooled kits include an 80W pump rated at 3500L/H with a 3.5M head, and the pump must stay fully immersed in water while it runs.

What collet sizes do CNC router spindles use?

ER11, ER20 and ER32 are the collet sizes in these kits. ER11 collets grip shanks from 1mm to 7mm, ER20 collets take 1/2 inch, 1/4 inch and 1/8 inch shanks, and ER32 collets fit the 4.5kW spindles. Match the collet to the bit shank before ordering a spare set.

How fast does a CNC router spindle spin?

Rated top speeds in these kits run from 12,000 RPM to 30,000 RPM, with the NYMOLABS 710W spindle adjustable from 7,000 to 30,000 RPM across 6-speed settings. The RATTMMOTOR 2.2kW spindles state a minimum speed of 9,000 rpm during use.

What voltage does a CNC router spindle need?

It depends on the kit. The kits in this guide use 110V or 220V input, and the Coolook 500W kit runs on 48V DC from a supply that takes AC 110V or 220V at 50/60Hz. Check the voltage on the kit before ordering.

Related: the CNC routers hub, CNC router types and CNC machine spare parts. Also see the CNC milling machine parts guide.

More buying guides

CNC Routers ·

CNC Machine Spare Parts to Keep on Hand

CNC machine spare parts are the fasteners, pulleys and brackets that wear out or go missing, and keeping the common ones on hand keeps…

CNC Routers ·

CNC Router Types: A Buyer’s Guide

Desktop, enclosed and large-format CNC router types compared by work area, spindle power and axis count to help match a machine to a project.

CNC Routers ·

What Can You Make with a CNC Router?

A practical guide explaining what you can make with a CNC router: carve wooden signs, cut trays and joinery, mill acrylic panels, and machine…