Limit Switch Types for CNC Machines: A Guide to Choosing the Right Switch
A guide to limit switch types for CNC machines, covering roller lever, snap action and vertical switches, plus the voltage and wiring details that matter when choosing a switch.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
10 Pcs Micro Limit Switch 250VAC 5A SPDT 1NO 1NC9.5/10View on Amazon - 2
OTOTEC 6pcs Micro Limit Switches Momentary Limit9.5/10View on Amazon - 3
HUAREW Vertical Limit Switch 3D Printer Switch9.4/10View on Amazon
Signs, tumblers, leather patches and cut parts all start the same way: a design file, a machine that holds its position, and a run that ends where it should. Limit switch types decide that last part. A limit switch tells the controller when an axis has reached the end of its travel, so the machine can home, stop and hold a repeatable zero. This guide explains the limit switch types found on CNC routers and laser machines, what each type does at the end of travel, and which voltage, pin and cable details to check before choosing.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Every voltage figure, pin count and compatibility note here comes from the listing for that switch. Where a listing stays silent, the guide says Not stated rather than filling the gap.

10 Pcs Micro Limit Switch 250VAC 5A SPDT 1NO 1NC
A 10 pc micro limit switch kit with SPDT contacts, a hinge roller lever and a stated operating range of -40°C to 70°C.
Pros
- SPDT contacts give 1 normally open and 1 normally closed contact in the same switch
- Hinge roller lever with short stroke for smooth, precise triggering, per the listing
- 250VAC 5A with a stated operating range of -40°C to 70°C and humidity up to 85%
- 10 switches in the kit, the largest pack here
Cons
- No machine compatibility is stated in the listing
- No warranty term is stated
- Plastic housing rather than a metal body
- No cable is stated in the listing

OTOTEC 6pcs Micro Limit Switches Momentary Limit
A 6 pc momentary micro limit switch kit with a 1m cable, rated 125V/250V AC 5A, for the Genmitsu 3020-PRO MAX.
Pros
- 125V/250V AC 5A with normally open contacts
- Ships with a 1m long 2 pin cable, ready to wire
- ABS and brass build, described as durable and heat-resistant in the listing
- Named compatibility with the Genmitsu 3020-PRO MAX CNC Machine
Cons
- No normally closed contact: normally open only
- No roller lever is stated in the listing
- No warranty term is stated
- No operating temperature range is stated

HUAREW Vertical Limit Switch 3D Printer Switch
A 6 pc vertical limit switch module with 3 pin normally open contacts, a trigger light and Genmitsu 3018-PROVer compatibility.
Pros
- Trigger light shows when the switch has been pressed
- 3 pin normally open contacts with momentary action
- Named compatibility with Genmitsu 3018-PROVer, 3018-MX3 and 3018-PROVer Mach3
- Small size with plug and play mounting on a 3D printed board, per the listing
Cons
- No voltage or current figures are stated
- No normally closed contact: normally open only
- No warranty term is stated
- No cable length is stated in the listing
Limit switch types for CNC machines
A limit switch is a small mechanical switch mounted where an axis ends its travel. When the moving carriage presses the actuator, the contacts change state and the controller knows the axis has arrived. The types below differ in how the moving part presses them, how many contacts they offer, and how they mount.
Roller lever switches
A roller lever switch carries a small wheel on a hinged arm. The carriage rolls onto the wheel, the arm pivots, and the contacts change state with a short stroke and smooth action, according to the Snuviax listing. The roller suits a carriage that approaches from the side, since the wheel turns as the carriage rolls onto it at the end of travel.
Snap action micro switches
A snap action micro switch with momentary action closes its contacts when the actuator is pressed and opens them again when the pressure leaves. The OTOTEC listing describes a contact that is open at rest and closes immediately when operated. This type suits a press at the end of travel, where the carriage meets the switch.
Vertical mount switches
A vertical mount switch stands upright on its mounting board, with a trigger light that shows when the switch has been pressed, according to the HUAREW listing. The listing describes a small size with easy installation, momentary action and contacts that are open at rest.
Voltage, current and wiring to check before choosing
The voltage and current figures state what the contacts are made to handle. The OTOTEC listing and the Snuviax listing state figures of 125V/250V AC 5A, while the HUAREW listing states no voltage or current figures, so that detail is Not stated for that switch. The OTOTEC and HUAREW listings state normally open contacts, while the Snuviax listing states SPDT contacts with 1 normally open contact and 1 normally closed contact, which gives the builder a choice of wiring.
Pin count and cable length shape the wiring. The HUAREW switch uses 3 pins and the Snuviax switch (on Amazon) uses 3 pins, while the OTOTEC switch (on Amazon) uses 2 pin terminals and ships with a 1m long 2 pin cable. A longer cable reaches a controller mounted away from the axis.
Compatibility is stated per machine. The HUAREW listing names the Genmitsu 3018-PROVer, 3018-MX3 and 3018-PROVer Mach3, the OTOTEC listing names the Genmitsu 3020-PRO MAX, and the Snuviax listing names no machine, described as a kit for 3D printer, microwave door and DIY electronic project use.
Limit switch types: the gear
Each switch below handles a part of the homing and end of travel job: the roller lever switch with a hinge roller actuator, the snap action switch with momentary action, and the vertical switch with an upright mount.
FAQ: lasers and CNC
What does a limit switch do on a CNC machine?
A limit switch tells the controller that an axis has reached the end of its travel. The controller uses that signal to home the axis, stop motion at the end of travel and hold a repeatable zero.
Which limit switch type suits a Genmitsu 3018-PROVer?
The HUAREW listing names the Genmitsu 3018-PROVer, 3018-MX3 and 3018-PROVer Mach3 as compatible machines. The OTOTEC listing names the Genmitsu 3020-PRO MAX instead, and the Snuviax listing names no machine at all.
What does normally open mean on a limit switch?
Normally open means the contact stays open at rest and closes when the switch is pressed. The contact opens again when the pressure leaves.
What does SPDT mean on a micro limit switch?
SPDT means the switch carries 1 normally open contact and 1 normally closed contact in the same body. The builder wires the contact that fits the controller.
Can a limit switch handle heat and humidity in a workshop?
The Snuviax listing states an operating range of -40°C to 70°C and humidity up to 85%. The HUAREW and OTOTEC listings state no temperature range, so that detail is Not stated for those switches.
Related: the best stepper driver for X-Carve guide, how to set up a spoilboard on a CNC and best CNC dust cover picks. Also see the best CNC laser for wood engraving guide.




