How to Spool Filament for 3D Printing, Step by Step
Seat refill filament on a reusable spool, or wind loose filament in even rows, clip the loose end, mount the spool on a bearing holder and store the rest so it feeds without tangles.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SUNLU PLA+2.0 3D Printer Filament9.7/10View on Amazon - 2
eSUN PLA Basic Filament 1.75mm9.7/10View on Amazon - 3
ANYCUBIC 3D Printer Filament Multicolor PLA Bundle 4KG9.6/10View on Amazon
A loose coil of filament is hard to print with: it tangles, it snags, and it feeds in fits and starts. How to spool filament is the fix: seat a pre-wound refill coil on a reusable spool, or wind a loose strand onto a spool in neat rows, keep the end clipped, and set the spool where it can turn freely while the printer pulls. The steps below walk through the whole job, from finding the loose end to storing the spools you are not using yet.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Filament and spools come in many sizes, so this guide states no fixed winding figure. Work from the spool and the filament in front of you, and check the fit before you wind.
Step 1: Free the end and check the core
Start by finding the loose end of the filament and keeping hold of it. A loose end that slips back into the coil tangles fast, so clip it or hold it until the spool is ready. Check the core of the refill: the MarsWork reusable spool (on Amazon) takes refill filament with a cardboard core inner diameter of approximately 82 mm (3.23 inches). The refill arrives already wound on that core, so it needs seating on the spool, not rewinding. If the refill core does not match the spool, stop and find the spool that fits it. The maker lists the spool for refill filament, with a strap for half-used filament and a built-in clip that holds the end in place. See the filament spool dimensions guide for standard sizes and fit.
Step 2: Open the reusable spool
The MarsWork reusable spool opens with a two-finger press, so press the release and lift the top half away from the base. Set the refill coil on the base with the core seated flat, then set the top half back on and press it closed. The coil is already wound, so seating it is the whole transfer. The spool should close all the way around, with no gap for the filament to slip through. If the spool will not close, lift the top half off and seat the coil again. The maker lists the spool for Bambu Lab 3D printers, and the color card system marks the material and color so you can tell filaments apart during swaps.
Step 3: Wind in even rows
This step is for loose filament with no core. Wind the filament onto the spool in rows that sit side by side, moving across the spool as each row fills. Keep a light, steady pull on the strand so the rows pack tight without stretching the filament. Never let the end go while you wind: if it slips, the coil loosens and the rows cross, and crossed rows catch on each other when the printer pulls. If a row crosses, unwind back past the crossing and wind it again. Work slowly enough to see each row land, and keep the strand feeding from the same side so the rows stay even. If your filament is a refill coil on a cardboard core, skip this step: the coil is already wound, and Step 2 seated it.
Step 4: Clip the end and lock the spool
Once the filament is on the spool, clip the loose end into the built-in filament clip on the spool so it cannot spring back into the coil. The MarsWork spool has an integrated clip that holds the filament end in place, and the included strap secures half-used filament when you swap rolls mid-use. If your spool has no clip, tuck the end through a hole in the spool flange or hold it with a small clip of your own. A clipped end is what keeps the spool tidy on the shelf and ready for the next print.
Step 5: Set the spool on a holder and feed the printer
Set the spool on a holder that lets it turn freely. Roller holders with bearings cut drag: the Weewooday holder (on Amazon) uses smooth bearings with silicone anti-slip mats, the Coliao holder (on Amazon) uses smooth bearings with a silicone anti-slip pad, and the maker lists both for PLA, ABS and TPU filament. The FYSETC freestanding rack (on Amazon) holds one 400x300mm spool or four standard 1kg rolls, with four PTFE tube fittings for guide tubes and a knob to adjust the width. Thread the filament end through the guide tube and into the printer, then turn the spool by hand to check that it rolls without catching. The how to change 3D printer filament guide walks through loading the printer itself.
Step 6: Store the spools you are not using
Spools you are not printing with belong on a rack, with the end clipped and the spool kept dry. The MAYJOY 2-tier rack (on Amazon) holds up to 12 standard 1kg spools, 6 per tier, and each tier supports up to 33 lbs. The EROTASH wall-mounted rack holds up to 20 rolls, and the gostle 7-tier rack holds over 80 1kg spools. The VIVO clamp-on holder takes up to 8 standard 1kg reels, four 3kg reels or two 5kg reels, and it clamps to desks up to 3.4 inches thick. Keep the rack in a dry spot: the how to store 3D filament guide covers dry storage, and the best filament dryer for Bambu guide covers drying gear for damp spools.
Common mistakes to avoid
- Letting go of the loose end while you wind, so the coil springs back and tangles.
- Winding crossed rows that catch on each other when the printer pulls.
- Forcing refill filament onto a spool whose core does not fit it.
- Leaving the end unclipped in storage, so the spool unwinds on the shelf.
- Mounting the spool where it cannot turn, so the printer drags the filament.
How to spool filament: the short version
- Find the loose end and keep hold of it.
- Check the core size against the spool.
- Open the reusable spool and seat the refill.
- Seat the refill coil, or wind loose filament in even rows with a light, steady pull.
- Clip the end into the spool clip.
- Mount the spool on a holder and store the rest dry.
FAQ: lasers and CNC
Can I wind filament onto a spool by hand?
Yes, for loose filament with no core. Hold the loose end, wind the strand onto the spool in even rows, and keep a light, steady pull so the rows pack tight. Clip the end when you stop so the coil cannot spring back.
What core size does refill filament need?
It depends on the spool. The MarsWork reusable spool takes refill filament with a cardboard core inner diameter of approximately 82 mm (3.23 inches). Check the core against the spool before you wind.
How do I keep filament from tangling on the spool?
For loose filament, wind in even rows and never let the end go while you wind. For a refill coil, seat it flat on the reusable spool. Clip the end into the spool clip when you stop, and set the spool on a holder with bearings so it turns freely while the printer pulls.
Can I reuse an empty spool with refill filament?
Yes, if the refill core fits the spool. The MarsWork reusable spool opens with a two-finger press and takes refill filament, with a strap for half-used filament and a built-in clip for the end.
How many spools can I store on one rack?
It depends on the rack. The MAYJOY 2-tier rack holds up to 12 standard 1kg spools, 6 per tier. The EROTASH wall-mounted rack holds up to 20 rolls, and the gostle 7-tier rack holds over 80 1kg spools.
What size filament do these holders fit?
The Weewooday and Coliao roller holders fit 1 kg spools of 1.75 mm PLA filament, and the MAYJOY rack also takes 200g and 500g spools. The Yeebyee holder works with 0.5KG, 1KG and 3KG spools of 1.75mm and 3.0mm filament.
Related: the 3D printers hub, filament spool dimensions and how to change 3D printer filament. Also see the how to store 3D filament guide.




