Filament Spool Dimensions: Standard Sizes and Fit Guide
A plain guide to filament spool dimensions, from standard spool sizes to hub holes and widths, and how to check fit before buying.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SUNLU 250g Filament Bundle 1.75mm9.6/10View on Amazon - 2
MarsWork Quick-Swap Reusable Spool for Refill9.6/10View on Amazon - 3
Dynta 250g PLA 3D Printer Filament for Beginners9.6/10View on Amazon - 4
MarsWork 2-Pack Quick-Swap Reusable Spools9.6/10View on Amazon
A spool that does not fit the holder can stall a print before it starts, so filament spool dimensions matter before the filament itself. Filament spool dimensions cover the spool diameter, the spool width and the hub hole in the middle, and those measurements decide whether a spool sits on a holder, spins freely and clears the space around it. This guide explains each measurement, gives the sizes stated in current listings, and shows how to check fit before ordering a refill spool or a small spool.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Listings state spool sizes in different ways, so this guide uses only the figures each listing states and says Not stated where a listing gives no figure.

SUNLU 250g Filament Bundle 1.75mm
A bundle of 8 small spools of 250g PLA in 8 colours, with a stated spool diameter of 140 mm, a width of 36 mm and a hub hole of 53 mm.
Pros
- Spool diameter of 140 mm, width of 36 mm and hub hole of 53 mm are all stated
- 8 spools of 250g in 8 colours, 2KG in total
- 1.75 mm PLA with ±0.02 mm tolerance and approximately 68m per spool
- AMS use is stated with a 250g spool adapter
Cons
- No warranty term is stated in the listing
- AMS use needs a printed adapter, which the listing does not include
- The listing states compatibility with 99% of FDM 3D printers with heated beds, so a printer without a heated bed is outside that stated range

MarsWork Quick-Swap Reusable Spool for Refill
A pack of 4 reusable spools with a two-finger press design for refill filament, sized for a cardboard core inner diameter of approximately 82 mm (3.23 inches).
Pros
- Two-finger press design opens the spool for swaps in seconds, per the listing
- Fits refill filament with a cardboard core inner diameter of approximately 82 mm (3.23 inches)
- Built-in filament clip holds filament ends in place, and a strap secures half-used filament
- Colour card system identifies material and colour at a glance
Cons
- No warranty term is stated in the listing
- No filament is included; the spool is empty and needs refill filament
- No hub hole diameter is stated in the listing
- The listing states compatibility with Bambu Lab 3D printers, with no other printer brands stated

Dynta 250g PLA 3D Printer Filament for Beginners
A set of 6 small spools of 250g PLA in 6 colours, with a 53 mm inner bore and 1.75 mm filament at ±0.02 mm.
Pros
- 6 spools of 250g in 6 colours, 1.5KG in total, for colour trials and small prints
- 53 mm inner bore designed for many compact and standard FDM spool holders, per the listing
- 1.75 mm filament with ±0.02 mm tolerance, mechanically wound for organized feeding
- Wide printer compatibility is stated, covering Bambu Lab, Creality, Prusa and Flashforge models
Cons
- No warranty term is stated in the listing
- No spool diameter or spool width is stated
- Best used within 3 months of opening, per the listing
- A spool axle over 53 mm needs a check of device support before purchase

MarsWork 2-Pack Quick-Swap Reusable Spools
A pack of 2 reusable spools with a two-finger press design for refill filament, sized for a cardboard core inner diameter of approximately 82 mm (3.23 inches).
Pros
- Two-finger press design opens the spool for swaps in seconds, per the listing
- Fits refill filament with a cardboard core inner diameter of approximately 82 mm (3.23 inches)
- Built-in filament clip holds filament ends in place, and a strap secures half-used filament
- Colour card system identifies material and colour at a glance
Cons
- No warranty term is stated in the listing
- No product dimensions are stated in the spec table
- No filament is included; the spool is empty and needs refill filament
- The listing states compatibility with Bambu Lab 3D printers, with no other printer brands stated
Filament spool dimensions: the standard sizes
No standard size is stated across the listings here. The SUNLU 250g spool (on Amazon) states a diameter of 140 mm, a width of 36 mm and a hub hole of 53 mm, while the MarsWork reusable spool states product dimensions of 7.09 inches x 7.09 inches x 2.76 inches, with no spool diameter or width stated separately. The chart below collects the stated figures for the spools in this guide.
| Spool | Diameter | Width | Hub hole or core fit |
|---|---|---|---|
| SUNLU 250g spool | 140 mm (5.51 inches) | 36 mm (1.42 inches) | 53 mm (2.09 inches) |
| Dynta 250g spool | Not stated | Not stated | 53 mm inner bore |
| MarsWork reusable spool | Not stated | Not stated | Refill core of approximately 82 mm (3.23 inches) |
The Dynta listing states a 53 mm inner bore and warns that a spool axle over 53 mm needs a check of device support before purchase. The Dynta small spools suit many compact and standard holders, per the listing, while a reusable spool suits refill filament that arrives without a spool of its own.
Small spools suit a maker who prints in small batches or wants several colours on hand without full-size spools. A reusable spool suits a maker who buys refill filament, since the spool itself stays in use while the filament changes. For the small spools, the hub hole decides the fit, and the width decides whether the spool clears the holder and the space beside it. For the reusable spool, the refill core fit decides whether refill filament loads.
How to measure a spool before you buy
Start with the holder, then compare it with the figures in the listing. A holder axle that is wider than the hub hole will not take the spool, and a spool that is wider than the space beside the holder may rub or may not fit, so check the hub hole and the width together:
- Hub hole: Check the hub hole or inner bore against the holder axle. The Dynta and SUNLU listings state 53 mm, with the SUNLU listing giving the same figure as 53 mm (2.09 inches).
- Diameter: Check the spool diameter against the space around the holder. The SUNLU listing states a spool diameter of 140 mm (5.51 inches). The MarsWork listing states product dimensions of 7.09 inches x 7.09 inches x 2.76 inches rather than a spool diameter, so no diameter figure is stated for that spool.
- Width: Check the spool width against the holder and the space beside it. The SUNLU listing states a spool width of 36 mm (1.42 inches).
- Refill core: For a reusable spool, check the refill core. The MarsWork listing states a fit for refill filament with a cardboard core inner diameter of approximately 82 mm (3.23 inches).
- Filament diameter: Check the filament diameter against the printer. The Dynta and SUNLU listings state 1.75 mm PLA with a tolerance of ±0.02 mm.
Spools and filament for these filament spool dimensions
The picks below match the measurements above: reusable spools for refill filament with a stated core fit, and small spools with stated hub holes.
FAQ: lasers and CNC
What is the standard filament spool size?
No standard size is stated across these listings. The SUNLU 250g spool states a diameter of 140 mm (5.51 inches), a width of 36 mm (1.42 inches) and a hub hole of 53 mm (2.09 inches), while the MarsWork reusable spool states product dimensions of 7.09 inches x 7.09 inches x 2.76 inches, with no spool diameter or width stated separately. Check the listing for the spool in hand, since sizes vary by maker, and match the stated figures to the holder in use.
What hub hole diameter fits a standard spool holder?
In these listings, the Dynta and SUNLU spools state a 53 mm inner bore and hub hole. The Dynta listing describes that bore for many compact and standard FDM spool holders, and also warns that a spool axle over 53 mm needs a check of device support before purchase, so measure the axle as well as the bore.
Do refill spools fit a reusable spool?
Refill filament fits the MarsWork reusable spool when the cardboard core has an inner diameter of approximately 82 mm (3.23 inches). The spool opens with a two-finger press, and the included strap secures half-used filament for storage.
How wide is a small 250g spool?
The SUNLU 250g spool states a width of 36 mm (1.42 inches). The Dynta 250g (on Amazon) spool states no width, so its width is Not stated.
Can small spools work with an AMS?
The SUNLU listing states that a 250g spool adapter is needed for AMS use. Search for a 250g spool adapter on printing platforms such as Makerworld, print the adapter, install it, and the SUNLU 250g PLA filament is then compatible with AMS, per the listing. The adapter is printed, not supplied with the filament, so allow for that step before the spool goes on the printer.
What filament diameter do these spools use?
The Dynta and SUNLU listings state 1.75 mm PLA filament with a tolerance of ±0.02 mm. The MarsWork listings state reusable spools for refill filament, with no filament diameter stated.
Related: the spool holder guide and the filament storage rack guide.




