How Long to Dry Filament (2026): A Step-by-Step Guide
How long to dry filament, step by step: spotting damp filament, loading the dryer, setting heat and humidity, and knowing when the spool is dry.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SUNLU Filament Dry Box9.7/10View on Amazon - 2
Qacoczme 3D Printing Filament Storage Box9.6/10View on Amazon - 3
Official Creality Filament Dryer 4 Spools9.6/10View on Amazon
A fresh spool should print clean lines and smooth walls, but a spool that has sat open in a damp room prints stringy lines, rough walls and weak layers instead. The fix is drying, and how long to dry filament comes down to the filament, how damp the spool is and the dryer doing the work: heat and moving air pull the moisture out, and the dryer holds the spool until the air inside stays dry.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
No fixed drying time is stated here, because the time depends on the filament type and how damp the spool is. The dryer figures in this guide come from the SUNLU S4 (on Amazon), and the steps below work without a clock: the dryer and the print tell the maker when the spool is dry.
Step 1: Spot damp filament
Damp filament shows itself in the print before it shows on the spool. Lines come out stringy, walls turn rough, layers bond weakly, and the nozzle pops and crackles as water in the filament turns to steam. A spool that snaps when bent may have gone brittle from moisture, and a print that keeps failing on settings that used to work is worth drying before anything else changes.
PLA, PETG, ABS, nylon and TPU all take up moisture from the air, and nylon and TPU take it up fastest. A spool left open on a shelf in a damp room is the usual case, and a spool that arrived sealed but sat in storage can be damp too. When the signs above show up, drying is the next move, not a new spool.
Step 2: Load the dryer
Load the spool into a dryer that fits it. The SUNLU S4 dryer cited here holds 4 spools of 1kg, with an interior of 450x210x211mm, and it fits 1.75mm, 2.85mm and 3.0mm filament. 3 circulation fans move the air around the spools for 360° surround heating, so the spools dry evenly. The maker lists a 1 Year warranty on the dryer.
Feed the filament out through the dryer outlet while it dries, so the printer can run straight from the dry box. The S4 feeds up to 4 printers concurrently, which suits a maker running more than a spool of work in a day. Keep the lid shut while it runs: an open lid lets damp room air back in and adds drying time.
Step 3: Set heat and humidity
Set the dryer to heat the spool and watch the humidity, not the clock. The SUNLU S4 heats up to 70°C with a 350W PTC heater, and its humidity control triggers at 30-50% relative humidity and stops under 25% relative humidity. The Triple-Safe System, with a backup thermal switch and software monitoring, watches the temperature and alerts on anomalies, so the dryer can run without the maker standing over it.
PLA dries at the mildest heat, while nylon takes the higher end of a dryer range; PETG, ABS and TPU fall in between. Pick the setting that fits the filament on the spool, then let the dryer hold it there until the humidity reading stops under 25% and stays there. Opening the lid mid-cycle lets damp air in, so leave it shut until the dryer says the spool is dry.
Step 4: Know when the spool is dry
The spool is dry when the dryer holds the humidity under 25% and the print runs clean. Run a small print after drying: smooth walls, clean lines and strong layers mean the moisture is gone, while stringing, popping and rough walls mean the spool needs more time in the dryer.
Do not judge dryness by how the spool looks: a damp spool looks the same as a dry spool, and only the humidity reading and the print show the difference. When the print runs clean, move the spool straight into sealed storage so it stays dry for the next job.
Common mistakes to avoid
- Drying a spool in open air and calling it dry: moving air alone, without heat in a closed box, leaves the spool damp.
- Leaving a dry spool open on a shelf, where it takes up moisture again before the next print.
- Mixing a damp spool with dry filament in the same box.
- Opening the dryer lid mid-cycle and letting damp room air back in.
- Guessing the heat setting instead of matching it to the filament type.
How long to dry filament: the short version
- Spot damp filament in the print: stringing, rough walls and weak layers.
- Load the spool in a dryer that fits it and shut the lid.
- Set the heat for the filament type and let the humidity fall under 25%.
- Print a small piece: clean lines mean the spool is dry, so store it sealed.
Everything after that is routine: dry the spool, store it sealed and keep the dryer shut while it runs.
FAQ: lasers and CNC
How long does PLA take to dry?
There is no fixed time: it depends on how damp the spool is and the dryer doing the work. Dry the spool until the dryer holds the humidity under 25% and the print runs clean, then store it sealed.
Can I dry filament without a dryer?
A dryer with controlled heat and moving air is the tool for the job. Air drying leaves moisture in the spool, so a damp spool needs heat and airflow in a closed box to come right.
What temperature dries filament?
It depends on the filament type, and the dryer cited here heats up to 70°C. Set the dryer to the heat that fits the filament on the spool and let it hold there until the humidity reading stops under 25%.
How do I store filament after drying?
Move the spool straight into sealed storage, such as a dry box, so it stays dry for the next print. See the best filament dry box guide and the best filament storage rack guide for storage that keeps spools dry.
Can I dry more than a spool at a time?
Yes, with a dryer that holds more than a spool: the SUNLU S4 cited here holds 4 spools of 1kg and feeds up to 4 printers concurrently. Load the spools, shut the lid and let the dryer work through the batch.
Does wet filament ruin a print?
It can: damp filament prints stringy lines, rough walls and weak layers, and the nozzle pops as water turns to steam. Dry the spool and the print runs clean.
Related: the dryer box guide, filament dryer vs dry box and best filament dry box. Also see our best filament storage rack. Also see our best filament dryer for nylon. Also see our best filament dryer for petg. Also see our best pla filament for 3d printers.




