Copper Sheet Thickness Chart for Engraving
A copper sheet thickness chart that pairs gauge with mm and inches, with sheet sizes and film protection for engraving and craft work.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Adrattnay 6-Pack 99.9% Pure Copper Sheets Metal 69.6/10View on Amazon - 2
2 Pcs 99.9% Pure Copper Sheet, 10" x 8"9.5/10View on Amazon - 3
2Pcs Pure Copper Sheet 8 x 12 Inch 24 Gauge/0.5mm9.5/10View on Amazon - 4
2 Pieces 99.9% Pure Copper Sheet, 6" x 6"9.5/10View on Amazon
A copper sheet thickness chart pairs a gauge number with the thickness it stands for, so you can match a sheet to the engraving or cutting job at hand. Copper sheet thickness chart figures come straight from the maker, with gauge, mm and inches printed side by side.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Gauge numbers alone do not tell you the thickness. Read the mm figure printed beside the gauge, and check the sheet size before ordering, since listings give sizes in inches and mm.

Adrattnay 6-Pack 99.9% Pure Copper Sheets Metal 6
A 6-pack of 99.9% pure copper sheets, 6 x 6 in at 24 gauge (0.5 mm), with film on each side and stated laser cutter compatibility.
Pros
- 6-pack of 6 x 6 in sheets at 24 gauge (0.5 mm)
- Maker states compatibility with hand tools, laser cutters and shears
- Protective film on each side, peeled off before use
- 99.9% pure copper with stated conductivity and ductility
Cons
- 24 gauge (0.5 mm) only; no thicker sheet in this pack
- 6 x 6 in size only; larger pieces need a bigger sheet
- Edges are sharp; the maker recommends gloves for cutting or bending
- No warranty term is stated

2 Pcs 99.9% Pure Copper Sheet, 10" x 8"
A 2-pack of 99.9% pure copper sheets, 10 x 8 in at 18 gauge (1 mm), with film on each side for crafting, jewelry, repairs and electrical work.
Pros
- 18 gauge (1 mm), the thickest sheet in this guide
- 10 x 8 in sheets give more room than the 6 x 6 in packs
- Film on each side guards against scratches and oxidation
- 99.9% pure copper, per the maker
Cons
- Laser cutting is not stated for this sheet
- 2 sheets only; a larger run needs more packs
- 18 gauge only; no thinner sheet in this listing
- 10 x 8 in size; larger pieces need a bigger sheet

2Pcs Pure Copper Sheet 8 x 12 Inch 24 Gauge/0.5mm
A 2-pack of copper sheets at 24 gauge (0.5 mm), 8 x 12 in, with film on each side for crafts, jewelry, repair, electrical and industry work.
Pros
- 24 gauge (0.5 mm) copper, easy to cut and solder per the maker
- Film on each side protects the surface from scratches
- Maker lists good conductivity and thermal conductivity
- Listed for crafts, jewelry, repair, electrical and industry work
Cons
- Laser cutting is not stated for this sheet
- 2 sheets only; a larger run needs more packs
- 24 gauge only; no thicker sheet in this listing
- No warranty term is stated

2 Pieces 99.9% Pure Copper Sheet, 6" x 6"
A 2-pack of 99.9% pure copper sheets, 6 x 6 in at 24 gauge (0.5 mm), with film attached for jewelry, crafts, modelers, repairs and electrical work.
Pros
- 99.9% pure copper, per the maker
- 24 gauge (0.5 mm) sheet, easy to cut and solder per the maker
- Film attached to guard the surface
- Listed for jewelry, crafts, modelers, repairs and electrical work
Cons
- 6 x 6 in size only; larger pieces need a bigger sheet
- 24 gauge only; no thicker sheet in this listing
- Edges are a little sharp, per the maker
- Laser cutting is not stated for this sheet
How to read the copper sheet thickness chart
Start with the gauge column, then read across to the thickness in mm and inches.
| Gauge | Thickness (mm) | Thickness (in) |
|---|---|---|
| 24 gauge | 0.5 mm | 0.02 in |
| 18 gauge | 1 mm | Not stated |
In the sheets listed here, 18 gauge measures 1 mm and 24 gauge measures 0.5 mm, so the 18 gauge sheet is the thicker sheet in this guide. The iteshuai, LSVERDE and Adrattnay sheets list 99.9% pure copper.
Match thickness to the job
The 0.5 mm sheets in this guide cover jewelry, crafts, modelers, repairs and electrical work, and the Adrattnay sheet adds stained glass repairs, RC car parts, architectural models and electrical grounding to that list. The Adrattnay listing says its 0.5 mm thickness balances flexibility and durability. The 1 mm LSVERDE sheet (on Amazon) lists the same kinds of work.
Film matters too. Each sheet in this guide carries film on the surface to guard against scratches and oxidation, and the film comes off before use. The iteshuai and Adrattnay listings warn that the edges are sharp, and the Adrattnay listing recommends gloves during cutting or bending.
Only the Adrattnay sheet states laser cutter compatibility, listing hand tools, laser cutters and shears with no annealing required, plus laser marking and laser cutting among its uses. The other sheets in this guide do not state laser cutting, so check the maker’s notes before you cut them with a laser. If you are pricing a machine for metal work, see our laser engraving machine for metal price guide.
Copper sheets for engraving and craft work
The sheets below carry the gauge, size and film protection the chart above describes, so you can match a pick to the thickness your job needs.
FAQ: lasers and CNC
What gauge copper sheet should I use for laser engraving?
Use the gauge your job needs, and check that the sheet states laser cutting. The sheets in this guide run from 24 gauge (0.5 mm) to 18 gauge (1 mm). Only the Adrattnay sheet states laser cutter compatibility.
How thick is 24 gauge copper sheet?
24 gauge copper sheet measures 0.5 mm, or 0.02 in, in the listings here.
How thick is 18 gauge copper sheet?
18 gauge copper sheet measures 1 mm in the listing here. The LSVERDE sheet lists 18 gauge at 1 mm, with a 10 x 8 in size.
Can a laser cut copper sheet?
It depends on the sheet and the machine. The Adrattnay listing states compatibility with laser cutters, plus laser marking and laser cutting among its uses. The other sheets in this guide do not state laser cutting.
Do copper sheets come with protective film?
Each sheet in this guide lists film on the surface to guard against scratches, and the LSVERDE, ZOFORTY and Adrattnay sheets list film on each side. Peel the film off before use.
Related: the engraving materials hub, plastic sheet thickness chart and size of MDF sheets. Also see our can a CO2 laser engrave metal guide.




