Best Way to Clean 3D Printer Nozzle: 4 Kits Compared
Heat the nozzle, push a needle through the bore, wipe the tip and check the flow, with four cleaning kits matched to the job.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
AJOYIB 3D Printer Nozzle Cleaner Kit9.7/10View on Amazon - 2
Creality 3D Printer Tool Kit9.6/10View on Amazon - 3
60 Pieces 3D Printer Nozzle Cleaning Kit,Stainless9.6/10View on Amazon - 4
50PCS 3D Printer Nozzle Cleaner9.6/10View on Amazon
The best way to clean 3d printer nozzle clogs is to heat the nozzle to printing temperature, push a cleaning needle through the bore to clear the blockage, wipe the tip clean, and then check the flow before starting the next print. A clogged nozzle shows up as thin lines, gaps in the first layer, or a print that stops feeding. The steps below walk through the clean in order.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

AJOYIB 3D Printer Nozzle Cleaner Kit
A 40-piece kit with 31 needles in 9 sizes, brass and stainless brushes, 2 tweezers and 5 sanding strips.
Pros
- 9 needle sizes from 0.15 to 0.8mm
- Brass and stainless brushes clean the heated hot end
- 2 tweezers keep fingers away from the hot end
- 5 sanding strips handle model finishing
Cons
- No storage bottles for the loose needles
- Sanding strips work on models, not on the nozzle
- Brushes need a heated hot end to work
- 9 sizes to sort through before each clean

Creality 3D Printer Tool Kit
A 74-piece tool kit with a nozzle cleaning set, screwdrivers, pliers and model tools for all printers.
Pros
- 74 pieces cover cleaning, assembly and model work
- 10 needles at 0.38mm plus a metal brush
- L-shaped hex wrench removes nozzles
- Tweezers for the silicone cap and surplus filament
Cons
- Nozzle cleaning is a small part of a large kit
- Needles come in one size only, 0.38mm
- No sanding strips for model finishing
- A 74-piece kit is bulky for a buyer who only needs needles

60 Pieces 3D Printer Nozzle Cleaning Kit,Stainless
A 60-piece set of stainless steel cleaning needles in 6 sizes, stored 10 to a bottle across 6 bottles.
Pros
- 6 needle sizes from 0.15 to 0.4mm
- 60 needles, 10 in each of 6 bottles
- Stainless steel needles are strong and flexible
- Handle design gives a smooth grip
Cons
- Largest size is 0.4mm, so bigger bores need another kit
- No brush for the hot end
- No tweezers for hot parts
- No warranty term is stated

50PCS 3D Printer Nozzle Cleaner
A 50-piece set of 0.4mm stainless steel cleaning needles in 2 bottles for a clogged 0.4mm nozzle.
Pros
- 50 needles at 0.4mm, 25 in each of 2 bottles
- Fits most FDM printers that use 1.75mm filament
- Flexible needles follow the nozzle interior
- No need to disassemble the hotend
Cons
- One size only, 0.4mm
- No brush for the hot end
- No tweezers for hot parts
- No warranty term is stated
The best way to clean 3d printer nozzle, step by step
Step 1: Heat the nozzle
Heat the nozzle to printing temperature before touching it with a needle. Vrezumv describes the same order: heat, then insert the needle. AJOYIB says to keep the hot end heated to over 200°C while unblocking.
Step 2: Push the needle through
Pick a needle that matches the nozzle bore, then push it gently through from the tip. A 0.4mm needle fits a 0.4mm nozzle, and the AJOYIB kit (on Amazon) covers 0.15 to 0.8mm for other sizes.
Step 3: Brush and wipe the hot end
While the hot end is still heated, brush off the nozzle and wipe away surplus filament. The AJOYIB kit has brass and stainless wire brushes for this, and the Creality kit (on Amazon) has a metal cleaning brush.
Step 4: Check the flow
Feed a little filament through and watch it come out in a straight line before the next print. If the line still curls or stops, repeat the needle pass while the nozzle is hot.
Cleaning kits for the job
The needle does the clearing work above, so pick by needle sizes, spares and extra tools.
When the needle is not enough
If a needle pass does not clear the bore, take the nozzle off instead. The Creality kit has an L-shaped hex wrench for removing nozzles. For a full nozzle swap instead of a clean, see how to change a 3D printer nozzle.
FAQ: lasers and CNC
What size cleaning needle fits a 0.4mm nozzle?
A 0.4mm needle fits a 0.4mm nozzle. The Vrezumv set has 50 needles at 0.4mm, the Mozeat set covers 0.15 to 0.4mm, and AJOYIB covers 0.15 to 0.8mm.
Do I need to remove the nozzle to clean it?
No. Vrezumv describes the clean with the nozzle still fitted: heat it to printing temperature and insert the needle, with no need to disassemble the hotend. The Creality kit includes an L-shaped hex wrench for removing nozzles.
How hot should the hot end be when cleaning?
Heat the nozzle to printing temperature before inserting a needle. AJOYIB says to keep the hot end heated to over 200°C while unblocking, and to use tweezers near the hot end.
What else in these kits cleans the nozzle?
The AJOYIB kit has a brass wire brush and a stainless wire brush for the heated hot end, and the Creality kit has a metal cleaning brush plus tweezers for surplus filament. The Mozeat and Vrezumv sets are needles only.
Related: the 3D printers hub, 3D printer nozzle types. Also see our how to change a 3D printer nozzle.




