Best Glue Stick for 3D Printer Bed (2026): 5 Picks Compared
Five glue sticks for 3D printer beds compared by stated filament fit, build surface fit, pack count and cleanup, from a 4 pcs mixed-filament pack to a Creality upkeep pack.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallFENGWANGLI Glue Sticks9.6/10View on Amazon - 2
Best for Creality FDMCreality Glue Pack9.5/10View on Amazon - 3
Best Pack CountCpybooder Glue Sticks9.4/10View on Amazon
A print that lifts at the corners can waste filament, time and a clean build surface, and warped edges can turn a saleable part into scrap. Makers who sell printed parts or run a busy bench want a part to stay put while it prints and release cleanly when it is done. This guide compares the best glue stick for 3d printer bed options by stated filament fit, build surface fit, pack count and cleanup, so you can match a stick to the filament and plate you already use.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall FENGWANGLI Glue Sticks: 4 pcs stated for PLA, ABS, PETG, PC, TPU and HIPS on glass, PEI, Buildtak and Kapton, with water cleanup. Check price on Amazon
- Best for Creality FDM Creality Glue Pack: PVP glue stick plus thermal grease and lubricant grease, stated for Creality FDM including Ender 3 series and K series. Check price on Amazon
- Best Pack Count Cpybooder Glue Sticks: 6 items stated for PLA, ABS, HIPS, PET and ASA, with cleanup by damp cloth or rinse with water. Check price on Amazon
Machines on the list

3D Printer Glue Sticks for Hot Bed
A 4 pcs glue stick pack stated for PLA, ABS, PETG, PC, TPU and HIPS on glass, PEI, Buildtak and Kapton, with water cleanup.
Pros
- Stated for PLA, ABS, PETG, PC, TPU and HIPS filaments
- Stated for glass, PEI, Buildtak and Kapton surfaces
- Maker states 100+ average prints and a water soluble formula
- Twist-up stick stated for use on the active printing area
Cons
- Pack is 4 pcs, below the 6 items stated for Cpybooder
- Stick material is Not stated
- Warranty term is Not stated
- Size is stated as 98mm x 24mm, so check grip fit for your hand

Creality 3D Printer Glue Sticks for Hot Bed
A pack of 2 Creality PVP glue sticks for PLA, ABS, PETG, PC, PA and TPU, water washable with no residue.
Pros
- 2 sticks in each pack
- PVP formula without formaldehyde
- Thin coatings with easy demolding after cooling
- Water washable with no residue left
Cons
- No stick size stated on the listing
- No bed surfaces named on the listing
- No warranty term stated on the listing
- No safety certification stated on the listing

Creality 3D Printer Glue Stic&Grease Pack
A Creality maintenance pack with a PVP glue stick for bed adhesion, thermal grease and lubricant grease, stated for Creality FDM printers.
Pros
- PVP glue stick stated as water-washable for cleanup
- Stated fit for Creality FDM including Ender 3 series and K series
- Thermal grease stated as heat-resistant to 250°C for hotend parts
- Lubricant grease stated for rails, lead screws and bearings
Cons
- Pack holds a single glue stick among its 3 items
- Filament list is Not stated
- Build surface list is Not stated
- Maker states to close the lid after each use to keep it from drying out

TEQStone 3D Printer Glue Stick 3 Pack
A 3-pack of 36g sticks, each good for more than 100 prints, for textured and smooth PEI, glass, aluminum and flexible plates.
Pros
- 3-pack of 36g sticks, each good for more than 100 prints
- At least 300 prints from one purchase, per the maker
- Works on textured and smooth PEI, glass, aluminum and flexible plates
- PVP formula with no unpleasant odors, and cleanup with a damp cloth or a rinse
Cons
- Covers ABS, PLA and PETG only; PC, PA, ASA and TPU are not listed
- Only a 3-pack is offered, with no single stick to try first
- A daily printer will go through the 3-pack faster than the 6-pack
- Cleanup needs a damp cloth or a rinse after each print

3D Printer Glue Stick – PVP Solid Glue for Heat
A 6 item PVP glue stick pack in blue, stated for PLA, ABS, HIPS, PET and ASA on smooth PEI, carbon crystal glass and flexible beds.
Pros
- Largest pack count here at 6 items
- PVP sticks stated for PLA, ABS, HIPS, PET and ASA
- Cleanup stated as a damp cloth wipe or a rinse with water
- Maker states non-toxic and odorless PVP material
Cons
- Maker states PETG, PC and TPU are not recommended
- Maker states nylon is not recommended
- Color is stated as blue, which may show on light plates
- Warranty term is Not stated
Specs compared
| Model | HQ Score | Pack | Filaments stated | Surfaces stated | Cleanup | Warranty |
|---|---|---|---|---|---|---|
| FENGWANGLI Glue Sticks | 9.6/10 | 4 pcs | PLA, ABS, PETG, PC, TPU, HIPS | Glass, PEI, Buildtak, Kapton | Water after drying | Not stated |
| Creality Glue Pack | 9.5/10 | 3 items with greases | Not stated | Not stated | Water-washable | Not stated |
| Cpybooder Glue Sticks | 9.4/10 | 6 items | PLA, ABS, HIPS, PET, ASA | Smooth PEI, carbon crystal glass, flexible | Damp cloth or rinse | Not stated |
| TEQStone Glue Sticks | 9.5/10 | 3 pack, 36g/1.27oz | ABS, PLA, PETG | Various build plate | Not stated | Not stated |
| Creality Glue Sticks | 9.6/10 | Pack of 2 | PLA, ABS, PETG, PC, PA, TPU | Not stated | Not stated | Not stated |
Specifications are manufacturer rated, as published by each maker and collected 22 November 2026.
A glue stick pack is not always just glue sticks
Pack contents differ more than the names suggest. The Creality Glue Pack is a maintenance pack: the maker states it includes a bed adhesive glue stick, thermal grease for the hotend and lubricant grease for rails and lead screws. That suits a Creality owner who wants upkeep supplies in a single order, and it suits a glue-only buyer less well. The other packs are plain glue sticks, stated at 6 items for Cpybooder, 4 pcs for FENGWANGLI, a 3 pack for TEQStone and a pack of 2 for the Creality Glue Sticks pack. Read pack count together with filament fit, because a larger pack helps little if the maker does not state your filament.
Filament fit is the sharpest split here. FENGWANGLI states PLA, ABS, PETG, PC, TPU and HIPS. The Creality Glue Sticks pack states PLA, ABS, PETG, PC, PA and TPU, and TEQStone states ABS, PLA and PETG. Cpybooder states PLA, ABS, HIPS, PET and ASA, and states the stick is not recommended for PEI, PETG, nylon, PC and TPU. The Creality Glue Pack states no filament list; it states printer fit for Creality FDM printers including the Ender 3 series and the K series, plus other standard FDM printers.
Buying guide: best glue stick for 3d printer bed
Match the filament
Start with the filament you print most. For PLA and ABS, FENGWANGLI, Cpybooder, TEQStone and the Creality Glue Sticks pack each state PLA and ABS. For PETG, choose from FENGWANGLI, TEQStone and the Creality Glue Sticks pack, which state PETG. For PC and TPU, FENGWANGLI and the Creality Glue Sticks pack state PC and TPU, while Cpybooder states PC and TPU are not recommended. For PA, only the Creality Glue Sticks pack states PA here. For HIPS, FENGWANGLI and Cpybooder state HIPS, and for PET and ASA, Cpybooder states PET and ASA. Where a maker does not state a filament, this guide writes Not stated rather than guess.
Match the build surface
FENGWANGLI states glass, PEI, Buildtak and Kapton, and also states build surface sheet plate and aluminum and glass plate. Cpybooder states smooth PEI, carbon crystal glass and flexible materials as suitable heated beds. TEQStone states various build plate in general words, with no named surface list. The Creality packs do not state a surface list. If you print on Kapton or Buildtak, FENGWANGLI names those surfaces. If you print on carbon crystal glass, Cpybooder names that surface. If your surface is not named for a pick, treat that fit as Not stated.
Cleanup and storage
The Creality Glue Pack maker states the glue stick is water-washable and states to close the lid after each use to keep it from drying out. Cpybooder states cleaning is a wipe with a damp cloth or a rinse with water. FENGWANGLI states a water soluble formula that can be cleaned with water after drying. For TEQStone and the Creality Glue Sticks pack, cleanup is Not stated.
Pack count and extras
Pack count ranges from a pack of 2 to 6 items here. The Creality Glue Pack is stated at 3 items in total, made up of a glue stick, thermal grease and lubricant grease, so it is not a multi-stick pack. FENGWANGLI states 100+ average prints for its glue stick, a maker figure to compare against pack count rather than a promise for your printer. Extras beyond sticks are stated only for the Creality Glue Pack, where thermal grease is stated as heat-resistant to 250°C and lubricant grease is stated for rails, lead screws and bearings.
Follow the maker guidance on materials and surfaces. Cpybooder states its stick is not recommended for PEI, PETG, nylon, PC and TPU, so do not treat that stick as a match for those materials. Close the lid after use where the maker states it, and clean residue with water only where the maker states water cleanup.
Project Match
- PLA or ABS parts on glass: FENGWANGLI states PLA, ABS and glass; Cpybooder states PLA, ABS and carbon crystal glass; TEQStone states PLA and ABS, surface Not stated.
- PETG parts: FENGWANGLI, TEQStone and the Creality Glue Sticks pack state PETG; Cpybooder states PETG is not recommended.
- PC or TPU parts: FENGWANGLI and the Creality Glue Sticks pack state PC and TPU; other picks state PC and TPU as Not stated or not recommended.
- Creality FDM upkeep with adhesion in a single order: the Creality Glue Pack states fit for Creality FDM including the Ender 3 series and the K series, plus thermal grease and lubricant grease; filament list Not stated.
- Kapton or Buildtak surfaces: FENGWANGLI states Kapton and Buildtak; other picks state those surfaces as Not stated.
How the scores add up
Each pick is scored out of 10 on performance, build, value, safety and warranty, with the weights published on our How We Pick page. A spec the maker does not publish scores nothing.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| FENGWANGLI Glue Sticks | 9.6 | 30 | 20 | 21 | n/a | 0 |
| Creality Glue Pack | 9.5 | 28 | 20 | 19 | n/a | 0 |
| Cpybooder Glue Sticks | 9.4 | 23 | 18 | 20 | n/a | 0 |
Scores never fall under 9.2 or rise above 9.8. A machine’s spot between those limits is set purely by its point total. Machines with a power supply, and items whose listing mentions safety features, are judged on safety; other items use a 90-point scale.
FAQ: lasers and CNC
Does a glue stick help prevent warping on a 3D printer bed?
The makers here state warping prevention as the purpose of these sticks. FENGWANGLI and TEQStone state prevents warping on the heat bed, the Creality Glue Pack states strong bed adhesion to prevent warping and lifting, and Cpybooder states strong adhesion with easy removal. Treat those as maker claims for the stated filaments and surfaces.
Which glue stick here is stated for PETG?
FENGWANGLI, TEQStone and the Creality Glue Sticks pack state PETG. Cpybooder states PETG is not recommended, and the Creality Glue Pack states no filament list, so PETG fit there is Not stated. See also our guide to types of PETG filament.
How do you clean glue stick from a build plate?
Use the cleanup the maker states. The Creality Glue Pack maker states water-washable cleanup, Cpybooder states a damp cloth wipe or a rinse with water, and FENGWANGLI states cleaning with water after drying. For TEQStone and the Creality Glue Sticks pack, cleanup is Not stated. Our guide on how to use glue stick on a 3D printer bed covers application in more detail.
Can a glue stick be used on PEI and glass?
FENGWANGLI states PEI and glass. Cpybooder states smooth PEI and carbon crystal glass as suitable heated beds, and also states PEI among materials that are not recommended, so check that point before ordering. For the other picks, PEI and glass fit is Not stated. If you are still deciding, see do I need to use glue stick for 3D printing.
Related: 3D printers, how to use glue stick on a 3D printer bed, do I need to use glue stick for 3D printing and types of PETG filament.




