Best Feeler Gauge for 3D Printer (2026): 5 Picks for Level Bed Gaps
5 dual-marked feeler gauge sets for 3D printer bed levelling, from a 26-blade set to two-piece sets with offset blades, compared by range, steel and warranty.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallGEARWRENCH 161D9.8/10View on Amazon - 2
Best Two-Piece SetSpurtar 2-Piece Set9.6/10View on Amazon - 3
Best Stainless SetPylevemv 2-Piece Set9.6/10View on Amazon - 4
Best Wide SpanSpurtar Tapered 329.6/10View on Amazon
A first layer that will not stick, a print that peels at the corners, a nozzle that drags through fresh filament: each can start with a bed gap that is a fraction too wide or too tight. A thin steel blade slipped between nozzle and bed shows the gap in a way eyes alone cannot, and the best feeler gauge for 3d printer bed levelling is the set whose blades cover the gaps a maker checks most, with markings that stay readable after months in a toolbox.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall GEARWRENCH 161D: 32 blades from 0.0015 to 0.035 in, a .010 brass blade for electronic ignitions and the only stated warranty here. Check price on Amazon
- Best Two-Piece Set Spurtar 2-Piece Set: 32 straight blades and 16 offset blades in #65 manganese steel, for open gaps and tight spaces in one pack. Check price on Amazon
- Best Stainless Set Pylevemv 2-Piece Set: Stainless steel blades that resist moisture and rust, with a hanging-hole box for wall storage. Check price on Amazon
- Best Wide Span Spurtar Tapered 32: Tapered blades from 0.001 to 0.04 in, the widest span here, in a folding plated steel case. Check price on Amazon
Machines on the list

GEARWRENCH 32 Blade Deluxe SAE/Metric Feeler Gauge
A 32-blade deluxe SAE and metric feeler gauge set with a .010 brass blade for electronic ignitions, blade length 3-5/16 in and blade width 1/2 in.
Pros
- 32 blades from 0.0015 to 0.035 in (0.038 to 0.889 mm), dual marked SAE and metric
- One .010 brass blade included for electronic ignitions
- Blade length 3-5/16 in and blade width 1/2 in are stated
- Standard Limited Lifetime warranty, the only stated warranty here
Cons
- Steel type is not stated in the listing
- No offset blades for tight spaces
- No case or storage detail is stated
- No rust protection or oil coating is named

Spurtar 2pcs Feeler Gauge Set Stainless Steel Dual
A two-piece set with 32 straight blades and 16 offset blades, dual marked SAE and metric, in #65 manganese steel with a rust-preventive oil coating.
Pros
- 32 straight blades and 16 offset blades in one pack
- Offset blades reach tight spaces without disassembly
- #65 manganese steel blades, hardened and polished, with a rust-preventive oil coating
- Etched size markings on every blade, made to resist wearing out
Cons
- No warranty term is stated
- Two-piece pack takes more storage space than a single folding set
- Offset range tops out at 0.020 in, below the straight set's 0.035 in
- Manganese steel needs its oil coating to stay rust-free

Pylevemv 2Pcs Feeler Gauges
A two-piece stainless steel set with 32 straight blades and 16 offset blades, dual marked SAE and metric from 0.0015 in to 0.035 in, in a box with a hanging hole.
Pros
- Stainless steel blades resist moisture and rust, with no special care needed
- 32 straight blades and 16 offset blades cover open gaps and tight spaces
- Dual markings from 0.0015 in to 0.035 in, with no burrs for repeatable stacking
- Box with a hanging hole for neat wall storage
Cons
- No warranty term is stated
- No blade length or width is stated
- Offset blade range is not stated separately from the straight range
- Stainless steel grade is not named in the listing

Spurtar Feeler Gauges 0.001-0.04" (0.03-1.00mm)
A 32-blade tapered feeler gauge set from 0.001 to 0.04 in (0.03 to 1.00 mm), dual marked SAE and metric, in flexible manganese steel with an oil coating.
Pros
- Widest span here: 0.001 to 0.04 in, from the thinnest to the thickest blade
- Tapered blades in flexible manganese steel, hardened and polished
- Folds into a plated steel case with a thumbscrew
- Etched size numbers with polished edges that do not hurt the hand
Cons
- No warranty term is stated
- No offset blades for tight spaces
- No blade length or width is stated
- Manganese steel needs its oil coating to stay rust-free

Stainless Steel Feeler Gauge Dual Marked Metric
A 26-blade feeler gauge set from 0.04 to 0.63 mm (0.0015 to 0.025 in), dual marked metric and imperial, in 65 manganese steel with anti-rust oil.
Pros
- 26 blades from 0.04 to 0.63 mm, with every metric size etched on the blades
- Foldable set, easy to take and store
- 65 manganese steel blades with anti-rust oil
- Dual metric and imperial markings for easy identification
Cons
- Narrowest range here: tops out at 0.63 mm
- No warranty term is stated
- No offset blades for tight spaces
Specs compared
| Model | HQ Score | Blades | Range | Steel | Offset | Warranty |
|---|---|---|---|---|---|---|
| GEARWRENCH 161D | 9.8/10 | 32 | 0.0015 to 0.035 in (0.038 to 0.889 mm) | Not stated | No | Standard Limited Lifetime |
| Spurtar 2-Piece Set | 9.6/10 | 32 straight + 16 offset | 0.0015 to 0.035 in straight; 0.005 to 0.020 in offset | #65 manganese steel | 16 | Not stated |
| Pylevemv 2-Piece Set | 9.6/10 | 32 straight + 16 offset | 0.0015 to 0.035 in | Stainless steel | 16 | Not stated |
| Spurtar Tapered 32 | 9.6/10 | 32 | 0.001 to 0.04 in (0.03 to 1.00 mm) | Manganese steel | No | Not stated |
| Hotop 26-Blade | 9.5/10 | 26 | 0.04 to 0.63 mm (0.0015 to 0.025 in) | 65 manganese steel | No | Not stated |
These numbers come straight from each maker’s listing and are rated, not measured by us (4 November 2026).
The best feeler gauge for 3d printer bed levelling
The sets here run from 26 to 48 blades, and the range each one covers matters more than the count. The thinnest blade in the group starts at 0.001 in, and the thickest reaches 0.04 in, so a maker who checks fine gaps wants the low end covered, while a maker who checks wider clearances wants the top end covered too. Dual markings keep the reading quick, and etched numbers stay readable.
Buying guide: feeler gauges for 3D printers
Match the blade range to the gap
Pick a set whose thinnest and thickest blades bracket the gaps the printer manual names. The Spurtar tapered set runs from 0.001 to 0.04 in, the widest span here, while the Hotop set runs from 0.04 to 0.63 mm, the narrowest. A set that stops short of the gap being checked leaves the maker guessing.
Straight or offset blades
Straight blades suit open gaps where the blade slides in flat. Offset blades bend at the end, and the bend lets the blade enter tight spaces and narrow gaps without disassembly, which the Pylevemv and Spurtar two-piece sets both list as their purpose.
Steel, markings and finish
Manganese steel blades come hardened and polished, and the Spurtar and Hotop listings say a light oil coating keeps rust away. Stainless steel resists moisture and rust without special care, which is what the Pylevemv listing claims. Etched markings survive handling, and polished edges slide in without catching.
Storage and care
Folding sets close into a case with a thumbscrew, and the Pylevemv set comes in a box with a hanging hole for a garage wall. Blades left loose lose their order and pick up nicks. Oil on the blades is normal: the Hotop listing says anti-rust oil is present and asks the buyer not to worry.
Feeler blades are thin steel with sharp edges. Keep the set folded in its case between jobs, and wipe the oil from a blade before it touches a print bed.
Project Match
- Bed levelling: any of the 5 sets, since all 5 list blades at the thin end of the range.
- Tight spaces: the Spurtar two-piece set and the Pylevemv set, the 2 listings with 16 offset blades.
- Spark plug gaps, valve clearances and piston ring gaps: the Spurtar tapered set, the Spurtar two-piece set and the Pylevemv set.
- Guitar setup: the Spurtar tapered set, the Spurtar two-piece set and the Pylevemv set.
- Electronic ignitions: the GEARWRENCH set, the only listing with a brass blade.
How the scores add up
Each gauge is scored on performance, build, value, safety and warranty. A spec the listing does not publish scores nothing.
FAQ: lasers and CNC
How to use a feeler gauge?
Pick the blade that matches the gap, slide it in flat, and feel for a light drag: a blade that slides through freely is thinner than the gap, and a blade that will not enter is thicker. Stack blades where the listing says stacking gives a repeatable reading.
Do feeler gauges need calibration?
The listings here do not state a calibration interval or a calibration service, so no listing in this guide promises one. Keep blades clean, oiled and flat, and replace a blade that is bent or nicked.
What is a feeler gauge set?
A feeler gauge set is a folding pack of thin steel blades, each etched with its thickness, used to measure the gap between two parts. The sets here hold from 26 to 48 blades, each set dual marked in SAE and metric.
How does a feeler gauge work?
A feeler gauge works by comparison: the maker tries blades of known thickness in the gap until one fits with a slight drag, and that blade’s etched size is the gap size. Thinner blades suit finer gaps, and offset blades reach gaps a straight blade cannot enter.
Related: best 3D printer bed adhesive, best tools to clean up 3D prints, best 3D printer nozzle cleaning kit and the 3D printer accessories hub.




