Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

3D Printer Extruder Problems and How to Fix Them

3D printer extruder problems traced to gear pressure, filament intake, nozzle size and version fit, with three replacement extruders compared.

3D Printer Extruder Problems and How to Fix Them
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1FLASHFORGE AD5X ExtruderFLASHFORGE AD5X Extruder9.6/10View on Amazon
  2. 2Creality Official Ender 3 Extruder Upgrade MetalCreality Official Ender 3 Extruder Upgrade Metal9.6/10View on Amazon
  3. 3Creality 3D Printer Extruder KitCreality 3D Printer Extruder Kit9.5/10View on Amazon

When a print that ran clean last week starts clicking, skipping or starving mid-layer, 3d printer extruder problems usually sit in the feed path: gear pressure, the filament intake, the nozzle size for the material, or a worn stock feeder. The checks below work through those points in order, using only what the makers of the replacement extruders here state.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

FLASHFORGE AD5X Extruder

FLASHFORGE AD5X Extruder

FLASHFORGE9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An entire extruder assembly with a 0.4 mm high-flow hotend rated to 32 mm3/s for the AD5X.

Pros

  • Entire extruder assembly with integrated hotend, handling feed and melt in one unit
  • Rated to 32 mm3/s with a 0.4 mm high-flow hotend kit stated
  • Nozzle options stated for standard and abrasive filaments
  • Version check by top cover shape stated, with no disassembly needed

Cons

  • V1 and V2 versions are not interchangeable, so version must be confirmed first
  • Fits the AD5X line, so Ender owners need a different extruder
  • Bed leveling calibration is stated as needed after replacement
  • No warranty term is stated
Creality Official Ender 3 Extruder Upgrade Metal

Creality Official Ender 3 Extruder Upgrade Metal

Creality9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An all-metal drive feeder with adjustable gear pressure and a 40-teeth gear for 1.75 mm filament.

Pros

  • Adjustable bolt sets gear pressure, handling the slipping-gear problem
  • 40-teeth drive gear feeds 1.75 mm filament as stated
  • Beveled intake stated to keep filament from scraping on entry
  • Aluminum alloy body stated as a metal upgrade over plastic stock

Cons

  • DIY kit that needs self-assembly, as stated by the maker
  • Fits listed Ender and CR models only, so other printers need another feeder
  • Feeder only, so hotend faults need separate parts
  • No warranty term is stated
Creality 3D Printer Extruder Kit

Creality 3D Printer Extruder Kit

Creality9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A metal extruder feeder kit with adjustable extrusion force for Ender and CR models.

Pros

  • Adjustable extrusion force by clamp tightness, handling loose gear mesh
  • Aluminum alloy body with oxidized sandblasted surface stated
  • Stated for PLA, ABS, TPU, carbon fiber, wood and gradient filaments
  • Feeder kit format for the listed Ender and CR models

Cons

  • Fits listed Ender and CR models only, so other printers need another feeder
  • No drive gear tooth count is stated for comparing grip
  • Feeder only, so hotend faults need separate parts
  • No warranty term is stated

3d printer extruder problems: where to look first

Start at the drive gear. The Creality metal extruders here use an adjustable bolt or clamp so gear pressure on the filament can be set as needed, and the maker states that a clamp set too loose lets the gear mesh poorly. If the gear slips or chews without feeding, pressure is the first setting to check before replacing parts.

Next, look at the filament intake. The Creality gray extruder has a beveled filament intake stated to keep the filament from scraping as it is pulled into the feeder. Scraped or shaved filament at the intake points to alignment and intake shape, not to the hotend.

Then check how filament is loaded and unloaded. FLASHFORGE states to always load and unload filament using the printer interface, since pulling filament out by hand may raise the risk of drive gear clogging. A clog that returns after manual pulls is a handling problem before it is a hardware problem.

Match the nozzle and version to the job

Nozzle size belongs in the same check. FLASHFORGE recommends 0.25 mm and 0.4 mm nozzles for PLA, PETG and ABS, and 0.6 mm and 0.8 mm nozzles for carbon fiber, glass fiber and other abrasive composites, stating that larger nozzle diameters lower the risk of clogging. Running abrasive filament through a small nozzle is a stated clog risk, so match the nozzle to the material before blaming the extruder body. Our best way to clean 3d printer nozzle guide covers the cleaning side, and how to change 3d printer nozzle covers the swap.

Version matters on the FLASHFORGE assembly (on Amazon). The maker states the AD5X extruder comes in V1 and V2 versions that are not interchangeable, with the top cover interface shape as the way to tell them apart without disassembly. Confirm the version before ordering a replacement, or the new assembly will not fit the job it was bought for.

After replacing the FLASHFORGE extruder, the maker states to perform bed leveling calibration for proper setup. Skipping that step can look like an extrusion fault when the first layer is really a setup fault. For the hotend side of the path, see 3d printer hot end parts.

The gear for extruder problems

When the checks above point to the feeder itself, these replacement extruders handle the gear-pressure, intake and hotend parts of the job.

FAQ: lasers and CNC

Why does my extruder gear slip instead of feeding?

Gear pressure is the first stated cause to check. The Creality metal extruders use an adjustable bolt or clamp to set gear pressure, and the maker states a clamp set too loose meshes poorly.

Why does filament get scraped at the extruder intake?

Intake shape plays a part. The Creality gray extruder has a beveled filament intake stated to keep filament from scraping as it is pulled into the feeder.

Which nozzle size suits abrasive filament?

FLASHFORGE recommends 0.6 mm and 0.8 mm nozzles for carbon fiber, glass fiber and other abrasive composites, and 0.25 mm and 0.4 mm nozzles for PLA, PETG and ABS.

Can I pull filament out by hand to clear a clog?

FLASHFORGE states to load and unload filament using the printer interface, since pulling filament out by hand may raise the risk of drive gear clogging.

What should I do after replacing the FLASHFORGE extruder?

FLASHFORGE states to perform bed leveling calibration after replacing the extruder to ensure proper setup and print quality.

Related: 3d printers, best way to clean 3d printer nozzle and how to change 3d printer nozzle.

More buying guides