Standard End Mill Size: Diameter Chart and Common Picks
Standard end mill sizes run in fractional steps from 1/8 to 3/4 inch and metric steps from 2 to 20 mm, and this guide charts them and compares 4 sets for CNC work.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
6Pcs Carbide Square End Mill Set 4-Flute TIALN9.7/10View on Amazon - 2
Shars 3/16" -3/4" HSS Single End Mill Set9.6/10View on Amazon - 3
8pcs 2-12mm CNC Square Nose End Mills,Carbide9.6/10View on Amazon - 4
Accusize Industrial Tools 20 Pc H.S.S. Tin Coated9.6/10View on Amazon
Cutting a slot, a pocket or a flat edge on a CNC mill starts with the diameter you load. This guide answers the standard end mill size question with a diameter chart and compares the sets that cover the standard sizes.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
There is no single standard diameter for every job. Match the diameter to the slot or pocket first, then check the shank fits your collet.

6Pcs Carbide Square End Mill Set 4-Flute TIALN
A 6-piece carbide set with a TiAlN coating, 4 flutes and diameters from 1/8 to 3/8, for steel work.
Pros
- Carbide core with TiAlN coating rated to 800℃
- 4-flute cutters, 35 to 38 degree helix angle, for clean finishes
- Covers 1/8 to 3/8 in 6 pieces
- Lists carbon steel, stainless steel, cast iron, aluminum, copper alloys
Cons
- Only 6 pieces, so fewer diameters than the 20-piece sets
- Largest diameter is 3/8
- Aimed at steel materials, not wood or plastic work
- No warranty term is stated

Shars 3/16" -3/4" HSS Single End Mill Set
A 20-piece HSS set in 3/16 to 3/4 diameters, with 2-flute and 4-flute cutters, in 4 shank sizes.
Pros
- 20 pieces cover 3/16 to 3/4
- 2-flute and 4-flute cutters in one set
- Center cutting, square end, Weldon flat shank
- Cut lengths 7/16 to 1-5/8; overall lengths 2-5/16 to 3-7/8
Cons
- No metric sizes: the set is fractional only
- Cut lengths top out at 1-5/8
- Single-end cutters only
- TiN coating only

8pcs 2-12mm CNC Square Nose End Mills,Carbide
An 8-piece carbide metric set with 4 flutes and diameters from 2 to 12 mm, in tungsten steel for CNC machining.
Pros
- 8 diameters, 2 to 12 mm, in one set
- Carbide tungsten steel with 4 flutes
- Tungsten carbide and cobalt at 99% of all components
- Large chip flute design for smoother chip removal
Cons
- No fractional sizes: the set is metric only
- Largest diameter is 12 mm
- 8 pieces, so fewer diameters than the 20-piece sets
- 4-flute cutters only

Accusize Industrial Tools 20 Pc H.S.S. Tin Coated
A 20-piece HSS metric set with TiN coating, 2-flute and 4-flute cutters and cutting diameters from 3 to 20 mm.
Pros
- 20 pieces cover metric diameters from 3 to 20 mm
- 2-flute and 4-flute cutters in one set
- HSS with a TiN coating
- Metric straight shank
Cons
- No warranty term is stated
- Metric only: inch drawings need a fractional set
- HSS cutters, not carbide
- 20 pieces to store and keep sorted
Standard End Mill Size: The Diameter Chart
End mills are stocked in stepped diameters, and the standard steps are the ones the sets in this guide carry between them. Fractional sets step through 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16 and 3/4 inch, while the Hunricho metric set steps through 2, 3, 4, 5, 6, 8, 10 and 12 mm and the Accusize metric set runs 3 to 20 mm.
| System | Sizes in this guide | Sets that carry them |
|---|---|---|
| Fractional (inch) | 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4 | Shars 20-piece; Pro Edge 6-piece |
| Metric (mm) | 2, 3, 4, 5, 6, 8, 10, 12 | Hunricho 8-piece |
| Metric (mm) | 3 to 20 | Accusize 20-piece |
How to Read an End Mill Size
A size listing gives the diameter, the shank, the cut length and the overall length. The cutting diameter is the width of the slot the cutter makes, and the shank is the part the collet grips: the Shars set groups its cutters under 3/8, 1/2, 5/8 and 3/4 shanks. Cut length is how deep the flutes reach, from 7/16 to 1-5/8 in the Shars set, and overall length is the full tool, from 2-5/16 to 3-7/8 in the same set.
Fractional or Metric: Which Set Fits Your Machine
Fractional and metric sets do the same work, so the choice comes down to the drawings and the collets a maker already owns. The Shars set covers the fractional range from 3/16 to 3/4, and the Pro Edge set covers 1/8 to 3/8. The Accusize set covers metric diameters from 3 to 20 mm, and the Hunricho set covers 2 to 12 mm in 8 sizes. A shop that works from inch drawings will reach for the fractional set most often, while a shop that works from metric drawings will reach for the metric set.
Carbide or HSS: Coating and Material
The sets split between high-speed steel and carbide. Shars and Accusize cutters are HSS with a TiN coating, while Pro Edge and Hunricho cutters (on Amazon) are carbide. The Pro Edge set adds a TiAlN coating rated to 800℃, with a helix angle of 35 to 38 degrees for clean finishes on flat surfaces, slots and edges. The Hunricho set is tungsten steel, mainly tungsten carbide and cobalt at 99%. For the full comparison, see our carbide vs HSS end mill guide.
End Mill Sets for Standard Sizes
The sets below cover the standard diameters above, fractional and metric, HSS and carbide.
Common Mistakes to Avoid
- Check the shank first: a 3/4 shank needs a 3/4 collet.
- Mixing systems: a 3 mm cutter is not a 1/8 cutter.
- Skipping the flute count: the sets here are 2-flute, 4-flute, or a mix.
- Forgetting cut length: match cut length to the pocket depth before ordering.
FAQ: lasers and CNC
What is the standard end mill size?
There is no single standard diameter: fractional shops stock 1/8 to 3/4 inch, metric shops 2 to 20 mm.
What shank size do I need for a 1/2 inch end mill?
The Shars set groups its 1/2 and 9/16 cutters under a 1/2 shank.
Are 2-flute or 4-flute end mills better for aluminum?
The listings do not rank flute counts by material; the Pro Edge 4-flute set lists aluminum among the metals it machines.
How many end mills are in a standard set?
The sets here hold 20, 20, 6 and 8 pieces.
Can I use a metric end mill in an inch collet?
The Accusize and Hunricho sets list straight shanks, while the Shars set lists a Weldon flat shank.
Related: the CNC tooling hub, carbide vs HSS end mill and roughing vs finishing end mill.




