Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Exhaust Fan Standard Size: Dimensions and Sizing Chart

Fan sizes are named by duct diameter, so this guide explains how to match an exhaust fan to a laser enclosure.

Exhaust Fan Standard Size: Dimensions and Sizing Chart
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1VIVOSUN P6 6" Inline Fan &Speed Control 345 CFM Exhaust FanVIVOSUN P6 6" Inline Fan &Speed Control 345 CFM Exhaust Fan9.7/10View on Amazon
  2. 2iLiving 12" Wall Mounted Shutter Exhaust FaniLiving 12" Wall Mounted Shutter Exhaust Fan9.7/10View on Amazon
  3. 3iLIVING 18" Wall Mounted Shutter Exhaust FaniLIVING 18" Wall Mounted Shutter Exhaust Fan9.7/10View on Amazon

A laser leaves smoke in the air and haze over the work, and the fan that clears it has to fit the duct and the enclosure it serves. Exhaust fan standard size is less a fixed measurement than a way of naming fans by the duct they fit, so the right choice starts with the duct and the port on your laser setup rather than a chart of universal sizes. The sections below explain how fan sizes are named, what to measure, and what a listed fan shows as a worked example.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

There is no universal standard size for exhaust fans. Fan sizes are named by duct diameter, and the figures that matter are the duct fit, the airflow and the static pressure the maker lists.

Exhaust Fan Standard Size: What the Term Means

Duct fan size names follow the duct the fan connects to, so read a fan size as a duct size and check it against your own duct. When a listing gives a body size in inches, that figure describes the fan housing; the duct diameter is the measurement that decides whether the fan joins your duct run. Measure the inside diameter of the duct and the port on the enclosure, then look for a fan that lists the same duct fit. A fan that is too small for the duct leaves gaps at the joint, and a fan that is too large needs an adapter to join the run.

The Creality Falcon EF1 (on Amazon) shows how the figures look on a fan made for laser cutting. The maker lists a 5-inch body with dimensions of 5.63 x 4.73 x 5.71 inches, so you can check the space beside the laser before ordering. The maker lists dual 14,000 RPM fans with an airflow of 135 CFM and a static pressure of 1,300 Pa, and the retractable PP duct measures 2.3m. Those figures describe that fan, not a standard, and other fans list their own figures in the same places.

How to Size an Exhaust Fan for Laser Cutting

Start with the duct and the enclosure port, then check the airflow and the static pressure. Airflow, given in CFM, is the volume of air the fan moves, and static pressure, given in Pa, is the push the fan gives against resistance in the duct. A fan with high airflow and low static pressure may clear a short, straight run yet struggle on a longer run with bends, so read those figures together rather than either figure alone.

Match the fan to the laser as well as to the duct. The Creality Falcon EF1 wirelessly syncs with the Falcon A1 Pro, and the fan adjusts power and airflow automatically based on the material. The maker lists compatibility with the Falcon2 Pro, Falcon A1, Falcon A1 Pro and Falcon T1, so check the compatibility list for your own machine before ordering. If your laser is not on the list, look for a fan that names your machine or your duct size.

Exhaust Fan Size Chart

The chart below gathers the figures the Creality Falcon EF1 lists, so you can see what a complete fan listing looks like and compare the same measurements on any other fan you consider.

Measurement Creality Falcon EF1
Body size 5-inch
Dimensions 5.63 x 4.73 x 5.71 inches
Fan speed 14,000 RPM
Airflow 135 CFM
Static pressure 1,300 Pa
Duct length 2.3m
Warranty 1 Year

Use the chart as a checklist, not as a standard. Any fan you compare should list the same measurements, and the figures you compare should come from the same kind of fan page, so a duct diameter matches a duct diameter and an airflow figure matches an airflow figure.

What the Creality Falcon EF1 Lists

The Falcon EF1 is an inline duct fan built for laser cutting, with dual 14,000 RPM fans. The maker lists an airflow of 135 CFM and a static pressure of up to 1,300 Pa. The maker describes the airflow and suction as shaped for the fine particulates and volatile fumes that laser cutting gives off, and the maker says the fan pulls smoke and fumes away at the source. The maker lists built-in sound-absorbing cotton and a quiet mode. The maker lists IP55 and a washable filter that rinses and reassembles without tools, and notes that exposed wires are not waterproof.

The fan also carries a retractable 2.3m PP duct for flexible placement beside the laser, and the maker lists a 1 Year warranty. The maker describes a smart double motor in the 5-inch body.

Setting Up the Duct Run

Route the duct from the fan to an outside vent or a window, and keep the run as short and straight as the room allows. Support the duct along its length so it does not sag or pull on the fan, and check the joints at the fan and at the enclosure port for gaps. A tight fit at each joint helps keep smoke moving outdoors instead of leaking back into the room.

Ventilation is part of laser safety, not an extra. Keep a suitable extinguisher within reach, never leave a running job unattended, and check the filter often so a clogged filter does not choke the airflow. For more on fume extraction, see the fume extractor guide, and for choosing the laser itself, see how to choose a laser engraver.

FAQ: lasers and CNC

What is the standard size of an exhaust fan?

There is no fixed standard size. Fan sizes are named by duct diameter, so measure your duct and your enclosure port, then look for a fan that lists the same duct fit. The Creality Falcon EF1 lists a 5-inch body. That figure describes the housing, so check the duct fit for your own duct and port as well.

How do I know which exhaust fan fits my laser?

Check the duct diameter, the enclosure port and the compatibility list. The Creality Falcon EF1 lists compatibility with the Falcon2 Pro, Falcon A1, Falcon A1 Pro and Falcon T1. If your machine is not on that list, look for a fan that names your machine or your duct size.

What do CFM and Pa mean on an exhaust fan?

CFM is the volume of air the fan moves, and Pa is the static pressure the fan gives against resistance in the duct. The Creality Falcon EF1 lists 135 CFM and 1,300 Pa. Read the figures together, since a fan needs airflow and pressure to clear a duct run.

Can I use a generic ventilation fan for laser cutting?

Check the duct fit, the airflow and the static pressure for any fan you consider. The maker describes the Falcon EF1 as purpose-built for laser cutting and engraving smoke, with airflow and suction shaped for fine particulates and volatile fumes. A fan with no stated figures for airflow or static pressure gives you nothing to compare, so look for a fan that states the figures.

How long is the duct on the Creality Falcon EF1?

The maker lists a retractable 2.3m PP duct, which gives flexible placement beside the laser. Measure the path from your fan to the outside vent before ordering, and check that the duct reaches with room to spare.

Related: the laser accessories hub, best fume extractor for laser engraver and best laser engraver for small business. Also see the laser engraver hub.

More buying guides